We thank the Life fund, University of Oklahoma Undergraduate Research Opportunities Program, and the Department of Zoology for funding this work. We also thank Dr. Mari&euml;lle Hoefnagels for editorial help.

1. Pre-recording, Live Animal Preparation
<ol>
	<li>Remove the scorpion from its home jar and place it in a pre-chilled glass container; next, place the jar containing the scorpion into a freezing environment (-5 &deg;C) for a minimum of two minutes. This time may vary according to the age, size, species, etc. of the specific scorpion under study. But generally, the freezing environment phase is complete once the animal is motionless.</li>
	<li>After two minutes, remove the immobilized scorpion from the cold glass container, and place it ventral side up on a microscope slide. Secure the stinger, tail, legs, and pedipalps with moldable clay (oil-based, Van Aken Plastalina).</li>
	<li>Make a platform on which to put the scorpion's pectines. Adjust the platform's length and width according to the size of the pecten. Typically, our platforms are constructed out of microscope cover glass and are approximately 10(L) X 18(W) mm.</li>
	<li>Adhere double-sided adhesive tape to the pecten platform, trimming the tape (if necessary) to fit.</li>
	<li>To make a pectinal chamber, put three of the platform's four sides into pre-melted wax (we use 100% beeswax chips) to a depth of 3-4 mm. We melt the wax by placing the chips within a glass petri dish, located on a hot plate. Once the wax on the edges of the pectinal chamber is cooled to room temperature, this should create walls of wax about 1 mm high.</li>
	<li>On the animal, locate the point of pectinal insertion, and place the un-waxed edge of the platform (tape side-up) just posterior to it. Afterward, stabilize the platform (so that it will not move later on) by gently pressing its right and left peripheral edges against the clay used to restrain the animal's legs.</li>
	<li>Use fine-tipped forceps to carefully place the pecten or pectines inside the chamber. Specifically, using forceps, hold the pecten along the pectinal spine, and gently bring the pecten out from underneath the cover glass and lower it onto the adhesive platform floor. Establish a pecten-to-tape bond by carefully applying pressure to the pectinal spine.</li>
	<li>Now apply melted wax (we use a pre-heated metal spatula) to the un-waxed edge of the platform. The purpose is two-fold, to secure the pecten and to fully enclose the chamber for future mineral oil introduction. Use caution when applying the wax over the animal's pecten, as it is possible to damage the pecten with wax that is too hot.</li>
	<li>The pecten chamber construction is complete. Next, establish an indifferent electrode connection with the animal's hemolymph by inserting a silver wire between two tail segments.</li>
</ol>
2. Simultaneous Extracellular Recording and Chemical Stimulation
<ol>
	<li>We prepare the animal 24 h prior to conducting extracellular, tip-recordings, which, among other reasons (i.e. animal adjustment to fixed position), allows time to custom-make stimulant pipettes of a specific (sensillum-dependent) tip-diameter. We use a micropipette puller for achieving such specifications. Ideally, the diameter of the pipettes is &asymp; 2 &mu;m larger than the sensillar pore diameter. We adjust our micropipette specifications accordingly for each animal.</li>
	<li>1 h prior to recording, we add 5 &mu;l of mineral oil to the pectinal chamber, submerging the pecten under oil. Then, we position the animal beneath a high-powered microscope, which has long working distance objectives and epi-illumination.</li>
	<li>To chemically stimulate peg sensilla, we introduce aqueous tastants (i.e. citric acid and salt) through the oil medium. First, we use a micropipette filler to inject the stimulant into the stimulant pipette. Note: all stimulant solutions should contain an electrolyte for electrical conductance.</li>
	<li>Next, after positioning the stimulant pipette on a micromanipulator (in the recording rig), insert the recording electrode into the blunt, open end of the stimulant pipette. It is important to ensure contact between the metal electrode and electrolytic stimulant solution.</li>
	<li>Once the preparation is electrically grounded (via the indifferent electrode), simply lower the pipette through the oil medium and onto a sensillar pore. The duration of chemical stimulation per pectinal sensillum can vary from as much as thirty minutes to as little as one second. Generally, we can sample multiple pegs (&gt; 30) per pipette. In the event that the stimulant pipette becomes clogged with minute debris, simply exchange the clogged pipette for a new, unused pipette.</li>
</ol>
3. Preparing an Animal for Multiple Days of Experimentation
<ol>
	<li>If the animal is to be used over an extended time period, we recommend reusing the pectinal chamber and replacing the drop of mineral oil for each recording session. After a given day's recording session is complete, remove the animal from the recording set-up and perform a mineral oil wash.</li>
	<li>Specifically, add another drop (5 &mu;l) of mineral oil to the chamber, and remove all oil. This helps minimize the presence of residual stimulant, which may have leaked out of the pipette during the recording session.</li>
	<li>Before the next session, add one drop of oil as described previously.</li>
</ol>
4. Representative Results:
Depending on the recording equipment used (e.g. the particular amplifier, digitizing hardware, etc.), a representative result is an extracellular recording with a S:N ratio of at least 3:1.
Successful construction of the mineral oil chamber is necessary for isolating chemical stimulation to individual sensilla, as it provides a medium for delivering polar (water-based) chemical tastants8. If there is too little oil or none at all, the stimulant solution will spread from the recorded sensillum to its neighboring sensilla, which is likely to cause a prolonged, uncontrolled bout of chemical stimulation8.

<ol>
	<li>Hodgson, E. S., Lettvin, J. Y., Roeder, K. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Physiology+of+a+Primary+Chemoreceptor+unit.">Physiology of a Primary Chemoreceptor unit.</a> Science. 12, 417-418 (1955).</li><li>Newland, P. L., Christensen, T. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Taste+processing+in+the+insect+nervous+system.">Taste processing in the insect nervous system.</a> Methods in Insect Sensory Neuroscience. , 289-318 (2005).</li><li>Foelix, R. F., M&#252;ller-Vorholt, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+fine+structure+of+scorpion+sensory+organs+II.+Pecten+sensilla.">The fine structure of scorpion sensory organs II. Pecten sensilla.</a> Bull. Br. Arachnol. Soc. 6, 68-74 (1983).</li><li>Carthy, J. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fine+structure+and+function+of+the+sensory+pegs+on+the+scorpion+pecten.">Fine structure and function of the sensory pegs on the scorpion pecten.</a> Experientia. 22, 89-91 (1966).</li><li>Gaffin, D. D., Brownell, P. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Response+properties+of+chemosensory+peg+sensilla+on+the+pectines+of+scorpions.">Response properties of chemosensory peg sensilla on the pectines of scorpions.</a> J. Comp. Physiol. A. 181, 291-300 (1997).</li><li>Wolf, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+pectine+organs+of+the+scorpion,+Vaejovis+spinigerus:+Structure+and+(glomerular)+central+projections.">The pectine organs of the scorpion, Vaejovis spinigerus: Structure and (glomerular) central projections.</a> Arthropod Struct. Dev. 37, 67-80 (2008).</li><li>Gaffin, D. D., Brownell, P. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Electrophysiological+evidence+of+synaptic+interactions+within+chemosensory+sensilla+of+scorpion+pectines.">Electrophysiological evidence of synaptic interactions within chemosensory sensilla of scorpion pectines.</a> J. Comp. Physiol. A. 181, 301-307 (1997).</li><li>Knowlton, E. D., Gaffin, D. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+new+approach+to+examining+scorpion+peg+sensilla:+the+mineral+oil+flood+technique.">A new approach to examining scorpion peg sensilla: the mineral oil flood technique.</a> J. Arachnol. 37, 379-382 (2009).</li><li>Knowlton, E. D., Gaffin, D. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+new+tip-recording+method+to+test+scorpion+pecten+chemoresponses+to+water-soluble+stimulants.">A new tip-recording method to test scorpion pecten chemoresponses to water-soluble stimulants.</a> J. Neurosci Methods. , .</li><li>Haupt, S. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Antennal+sucrose+perception+in+the+honey+bee+(Apis+mellifera+L.):+behaviour+and+electrophysiology.">Antennal sucrose perception in the honey bee (Apis mellifera L.): behaviour and electrophysiology.</a> J. Comp. Physiol. A. 190, 735-745 (2004).</li><li>Bland, R. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sensilla+on+the+antennae,+mouthparts,+and+body+of+the+larva+of+the+alfalfa+weevil,+hypera+postica+(gyllenhal)+(Coleoptera+:+Curculionidae).">Sensilla on the antennae, mouthparts, and body of the larva of the alfalfa weevil, hypera postica (gyllenhal) (Coleoptera : Curculionidae).</a> Int. J. Insect Morphol. Embryol. 12, 261-272 (1983).</li><li>Cate, H. S., Derby, C. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hooded+Sensilla+Homologues:+Structural+Variations+of+a+Widely+Distributed+Bimodal+Chemomechanosensillum.">Hooded Sensilla Homologues: Structural Variations of a Widely Distributed Bimodal Chemomechanosensillum.</a> J. Comp. Neurol. 444, 345-357 (2002).</li></ol>

We have previously published these methods in two journals, Knowlton and Gaffin (2009) and Knowlton and Gaffin (in press).

The protocol above describes how to prepare a desert grassland scorpion (Paruroctonus utahensis) for electrophysiological study. Specifically, we show how to build a chamber for controlled extracellular tip-recordings of pectinal chemosensory neurons under oil. Because oil and water do not mix, it is possible to isolate chemical stimulation (with water-based stimulants) to single sensilla. It should be stressed that P. utahensis, is a relatively small animal (&asymp; 2.5-5 cm) and applying this protocol to larger animals may require many size adjustments, such as the size of the animal's platform, chamber, and amount of oil applied. We recommend conducting pilot studies to test the minimum amount of oil necessary for controlled delivery of water-based chemical stimulants.
Furthermore, we found no effect of oil on the baseline neural activity within pectinal sensilla8. This should be confirmed for other model systems as well, prior to assessing chemoresponsiveness.
This method may be used in conjunction with another method to test for chemoresponse interaction effects among sensilla in the sensory field. For example, it is possible to tip-record (under oil) from one sensillum as we base-record (via a tungsten electrode) from a neighboring sensillum9. Such a recording configuration may be used to assess whether or not chemically stimulating one sensillum affects the neural activity of the base-recorded sensillum. To date, no one has tested this for scorpion pectinal sensilla, and it remains an open question for other chemosensory systems as well.
To summarize, we think the tip-recording method under oil advances the scope of electrophysiological investigations into the neural basis of arthropod gustation. In this manuscript, we provide a protocol for preparing animals for this method, and we hope it provides a firm foundation for further study of peripheral sensory nervous systems.

<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en">	
		
		<div>
		<table border="1">
		<thead>
		<tr>
		<th>Material Name</th>
		<th>Type</th>
		<th>Company</th>
		<th>Catalogue Number</th>
		<th>Comment</th>
		</tr>
		</thead>
		<tbody>
		
<tr>
<td>Lift-N-Press tab</td>
<td>&nbsp;</td>
<td>Ted Pella, Inc.</td>
<td>16082</td>
<td>Doubled-sided adhesive</td>
</tr>
<tr>
<td>MicroFil</td>
<td>&nbsp;</td>
<td>World Precision Instruments, Inc.</td>
<td>MF34G</td>
<td>Micropipette filler</td>
</tr>
<tr>
<td>Standard Glass Capillaries</td>
<td>&nbsp;</td>
<td>World Precision Instruments, Inc.</td>
<td>1B100F-6</td>
<td>Glass pipettes</td>
</tr>
<tr>
<td>Microelectrode Holder</td>
<td>&nbsp;</td>
<td>World Precision Instruments, Inc. </td>
<td>MEH3SBW10</td>
<td>&nbsp;</td>		</tbody>
		</table>
		</div>

electrophysiology of scorpion peg sensilla

We describe a modification of an existing tip-recording technique1,2 for electrophysiologically investigating short, peg-like sensory sensilla3,4. On the mid-ventral surface of all scorpions are two appendages called pectines, which have dense fields of mechano- and chemosensory peg sensilla5,6. One method for assessing chemoresponsiveness of these sensilla uses a tungsten electrode for extracellularly recording neural activity within a sensillum as a volatile odorant is introduced to the sensory field5,7. The limitations of this method include slow data collection and uncontrolled stimulant introduction to, and removal from, the peg field. To overcome these limitations, we developed a new tip-recording technique that uses nonpolar mineral oil as a medium through which to deliver water-based tastants to individual peg sensilla8,9. We have successfully applied this method to obtain sensillar chemoresponses to citric acid, ethanol, and salt. Here we describe the experimental protocol for such a study9. We think this new method may be useful for studying the response properties of other arthropod chemosensory systems, including those of insects10, 11 and crustaceans12.

Watch this Scientific Journal Video about Electrophysiology of Scorpion Peg Sensilla at JoVE.com

Electrophysiology of Scorpion Peg Sensilla

This article describes an electrophysiological method for isolating chemical stimulation to individual sensilla via extracellular, tip-recordings under mineral oil.

We describe a modification of an existing tip-recording technique1,2 for electrophysiologically investigating short, peg-like sensory sensilla3,4. On the ...

electrophysiology-of-scorpion-peg-sensilla

Research

JoVE Journal

Neuroscience

8.9K Views.  University of Oklahoma. This article describes an electrophysiological method for isolating chemical stimulation to individual sensilla via extracellular, tip-recordings under mineral oil.

Video: Electrophysiology of Scorpion Peg Sensilla

Simultaneous fMRI and Electrophysiology in the Rodent Brain

To examine the neural basis of the blood oxygenation level dependent (BOLD) magnetic resonance imaging (MRI) signal, we have developed a rodent model in which functional MRI data and in vivo intracortical recording can be performed simultaneously. The combination of MRI and electrical recording is technically challenging because the electrodes used for recording distort the MRI images and the MRI acquisition induces noise in the electrical recording. To minimize the mutual interference of the two modalities, glass microelectrodes were used rather than metal and a noise removal algorithm was implemented for the electrophysiology data. In our studies, two microelectrodes were separately implanted in bilateral primary somatosensory cortices (SI) of the rat and fixed in place. One coronal slice covering the electrode tips was selected for functional MRI. Electrode shafts and fixation positions were not included in the image slice to avoid imaging artifacts. The removed scalp was replaced with toothpaste to reduce susceptibility mismatch and prevent Gibbs ringing artifacts in the images. The artifact structure induced in the electrical recordings by the rapidly-switching magnetic fields during image acquisition was characterized by averaging all cycles of scans for each run. The noise structure during imaging was then subtracted from original recordings. The denoised time courses were then used for further analysis in combination with the fMRI data. As an example, the simultaneous acquisition was used to determine the relationship between spontaneous fMRI BOLD signals and band-limited intracortical electrical activity. Simultaneous fMRI and electrophysiological recording in the rodent will provide a platform for many exciting applications in neuroscience in addition to elucidating the relationship between the fMRI BOLD signal and neuronal activity.

We have developed a method for simultaneous functional magnetic resonance imaging and electrophysiological recording in the rodent brain, providing a platform for the investigation of the relationship between neural activity and the blood oxygenation level dependent (BOLD) MRI signal.

To examine the neural basis of the blood oxygenation level dependent (BOLD) magnetic resonance imaging (MRI) signal, we have developed a rodent model in ...

Spinal Cord Electrophysiology II: Extracellular Suction Electrode Fabrication

Development of neural circuitries and locomotion can be studied using neonatal rodent spinal cord central pattern generator (CPG) behavior. We demonstrate a method to fabricate suction electrodes that are used to examine CPG activity, or fictive locomotion, in dissected rodent spinal cords. The rodent spinal cords are placed in artificial cerebrospinal fluid and the ventral roots are drawn into the suction electrode. The electrode is constructed by modifying a commercially available suction electrode. A heavier silver wire is used instead of the standard wire given by the commercially available electrode. The glass tip on the commercial electrode is replaced with a plastic tip for increased durability. We prepare hand drawn electrodes and electrodes made from specific sizes of tubing, allowing consistency and reproducibility. Data is collected using an amplifier and neurogram acquisition software. Recordings are performed on an air table within a Faraday cage to prevent mechanical and electrical interference, respectively.

A demonstration of the fabrication and use of an extracellular suction electrode used to measure electrophysiological recordings of neonatal rodent spinal cords in vitro

Development of neural circuitries and locomotion can be studied using neonatal rodent spinal cord central pattern generator (CPG) behavior. We demonstrate ...

Culturing and Electrophysiology of Cells on NRCC Patch-clamp Chips

Due to its exquisite sensitivity and the ability to monitor and control individual cells at the level of ion channels, patch-clamping is the gold standard of electrophysiology applied to disease models and pharmaceutical screens alike 1. The method traditionally involves gently contacting a cell with a glass pipette filled by a physiological solution in order to isolate a patch of the membrane under its apex 2. An electrode inserted in the pipette captures ion-channel activity within the membrane patch or, when ruptured, for the whole cell. In the last decade, patch-clamp chips have been proposed as an alternative 3, 4: a suspended film separates the physiological medium from the culture medium, and an aperture microfabricated in the film replaces the apex of the pipette. Patch-clamp chips have been integrated in automated systems and commercialized for high-throughput screening 5. To increase throughput, they include the fluidic delivery of cells from suspension, their positioning on the aperture by suction, and automated routines to detect cell-to-probe seals and enter into whole cell mode. We have reported on the fabrication of a silicon patch-clamp chip with optimized impedance and orifice shape that permits the high-quality recording of action potentials in cultured snail neurons 6; recently, we have also reported progress towards interrogating mammalian neurons 7. Our patch-clamp chips are fabricated at the Canadian Photonics Fabrication Centre 8, a commercial foundry, and are available in large series. We are eager to engage in collaborations with electrophysiologists to validate the use of the NRCC technology in different models. The chips are used according to the general scheme represented in Figure 1: the silicon chip is at the bottom of a Plexiglas culture vial and the back of the aperture is connected to a subterranean channel fitted with tubes at either end of the package. Cells are cultured in the vial and the cell on top of the probe is monitored by a measuring electrode inserted in the channel.The two outside fluidic ports facilitate solution exchange with minimal disturbance to the cell; this is an advantage compared to glass pipettes for intracellular perfusion.
<img alt="Figure 1" src="/files/ftp_upload/3288/3288fig1.jpg" />
Figure 1. Principle of measurement using the NRCC patch-clamp chip
We detail here the protocols to sterilize and prime the chips, load them with medium, plate them with cells, and finally use them for electrophysiological recordings.

We show how planar patch-clamp chips fabricated at the National Research Council of Canada are sterilized, primed, loaded with medium, plated with cells, and used for electrophysiological recordings.

Due to its exquisite sensitivity and the ability to monitor and control individual cells at the level of ion channels, patch-clamping is the gold standard ...

Paired Nanoinjection and Electrophysiology Assay to Screen for Bioactivity of Compounds using the Drosophila melanogaster Giant Fiber System

Screening compounds for in vivo activity can be used as a first step to identify candidates that may be developed into pharmacological agents1,2. We developed a novel nanoinjection/electrophysiology assay that allows the detection of bioactive modulatory effects of compounds on the function of a neuronal circuit that mediates the escape response in Drosophila melanogaster3,4. Our in vivo assay, which uses the Drosophila Giant Fiber System (GFS, Figure 1) allows screening of different types of compounds, such as small molecules or peptides, and requires only minimal quantities to elicit an effect. In addition, the Drosophila GFS offers a large variety of potential molecular targets on neurons or muscles. The Giant Fibers (GFs) synapse electrically (Gap Junctions) as well as chemically (cholinergic) onto a Peripheral Synapsing Interneuron (PSI) and the Tergo Trochanteral Muscle neuron (TTMn)5. The PSI to DLMn (Dorsal Longitudinal Muscle neuron) connection is dependent on D&alpha;7 nicotinic acetylcholine receptors (nAChRs)6. Finally, the neuromuscular junctions (NMJ) of the TTMn and the DLMn with the jump (TTM) and flight muscles (DLM) are glutamatergic7-12. Here, we demonstrate how to inject nanoliter quantities of a compound, while obtaining electrophysiological intracellular recordings from the Giant Fiber System13 and how to monitor the effects of the compound on the function of this circuit. We show specificity of the assay with methyllycaconitine citrate (MLA), a nAChR antagonist, which disrupts the PSI to DLMn connection but not the GF to TTMn connection or the function of the NMJ at the jump or flight muscles.
Before beginning this video it is critical that you carefully watch and become familiar with the JoVE video titled "Electrophysiological Recordings from the Giant Fiber Pathway of D. melanogaster " from Augustin et al7, as the video presented here is intended as an expansion to this existing technique. Here we use the electrophysiological recordings method and focus in detail only on the addition of the paired nanoinjections and monitoring technique.

Paired Nanoinjection and Electrophysiology Assay to Screen for Bioactivity of Compounds using the Drosophila melanogaster Giant Fiber System

A rapid in vivo assay to test for neuromodulatory compounds using the Giant Fiber System (GFS) of Drosophila melanogaster is described. Nanoinjections in the head of the animal along with electrophysiological recordings of the GFS can reveal bioactivity of compounds on neurons or muscles.

Screening compounds for in vivo activity can be used as a first step to identify candidates that may be developed into pharmacological agents1,2. We ...

An Isolated Semi-intact Preparation of the Mouse Vestibular Sensory Epithelium for Electrophysiology and High-resolution Two-photon Microscopy

Understanding vestibular hair cells function under normal conditions, or how trauma, disease, and aging disrupt this function is a vital step in the development of preventative approaches and/or novel therapeutic strategies. However, the majority of studies looking at abnormal vestibular function have not been at the cellular level but focused primarily on behavioral assays of vestibular dysfunction such as gait analyses and vestibulo-ocular reflex performance. While this work has yielded valuable data about what happens when things go wrong, little information is gleaned regarding the underlying causes of dysfunction. Of the studies that focus on the cellular and subcellular processes that underlie vestibular function, most have relied on acutely isolated hair cells, devoid of their synaptic connections and supporting cell environment. Therefore, a major technical challenge has been access to the exquisitely sensitive vestibular hair cells in a preparation that is least disrupted, physiologically. Here we demonstrate a semi-intact preparation of the mouse vestibular sensory epithelium that retains the local micro-environment including hair cell/primary afferent complexes.

Analysis of vestibular hair cell function is complicated by their location deep within the hardest part of the skull, the petrous temporal bone. Most functional hair cell studies have used acutely isolated hair cells. Here we describe a semi-intact preparation of mouse vestibular epithelium for electrophysiological and two-photon microscopy studies.

Understanding vestibular hair cells function  under normal conditions, or how trauma, disease, and aging disrupt this  function is a vital step in the ...

Electrophysiological Recording From Drosophila Labellar Taste Sensilla

The peripheral taste response of insects can be powerfully investigated with electrophysiological techniques. The method described here allows the researcher to measure gustatory responses directly and quantitatively, reflecting the sensory input that the insect nervous system receives from taste stimuli in its environment. This protocol outlines all key steps in performing this technique. The critical steps in assembling an electrophysiology rig, such as selection of necessary equipment and a suitable environment for recording, are delineated. We also describe how to prepare for recording by making appropriate reference and recording electrodes, and tastant solutions. We describe in detail the method used for preparing the insect by insertion of a glass reference electrode into the fly in order to immobilize the proboscis. We show traces of the electrical impulses fired by taste neurons in response to a sugar and a bitter compound. Aspects of the protocol are technically challenging and we include an extensive description of some common technical challenges that may be encountered, such as lack of signal or excessive noise in the system, and potential solutions. The technique has limitations, such as the inability to deliver temporally complex stimuli, observe background firing immediately prior to stimulus delivery, or use water-insoluble taste compounds conveniently. Despite these limitations, this technique (including minor variations referenced in the protocol) is a standard, broadly accepted procedure for recording Drosophila neuronal responses to taste compounds.

Electrophysiological Recording From Drosophila Labellar Taste Sensilla

This protocol describes extracellular recording of the action potential responses fired by labellar taste neurons in Drosophila.

The peripheral taste response of insects can be powerfully investigated with electrophysiological techniques. The method described here allows the ...

Real-time Electrophysiology: Using Closed-loop Protocols to Probe Neuronal Dynamics and Beyond

Experimental neuroscience is witnessing an increased interest in the development and application of novel and often complex, closed-loop protocols, where the stimulus applied depends in real-time on the response of the system. Recent applications range from the implementation of virtual reality systems for studying motor responses both in mice1 and in zebrafish2, to control of seizures following cortical stroke using optogenetics3. A key advantage of closed-loop techniques resides in the capability of probing higher dimensional properties that are not directly accessible or that depend on multiple variables, such as neuronal excitability4 and reliability, while at the same time maximizing the experimental throughput. In this contribution and in the context of cellular electrophysiology, we describe how to apply a variety of closed-loop protocols to the study of the response properties of pyramidal cortical neurons, recorded intracellularly with the patch clamp technique in acute brain slices from the somatosensory cortex of juvenile rats. As no commercially available or open source software provides all the features required for efficiently performing the experiments described here, a new software toolbox called LCG5 was developed, whose modular structure maximizes reuse of computer code and facilitates the implementation of novel experimental paradigms. Stimulation waveforms are specified using a compact meta-description and full experimental protocols are described in text-based configuration files. Additionally, LCG has a command-line interface that is suited for repetition of trials and automation of experimental protocols.

Closed-loop protocols are becoming increasingly widespread in modern day electrophysiology. We present a simple, versatile and inexpensive way to perform complex electrophysiological protocols in cortical pyramidal neurons in vitro, using a desktop computer and a digital acquisition board.

Experimental neuroscience is witnessing an increased interest in the development and application of novel and often complex, closed-loop protocols, where ...

Electrophysiology on Isolated Brainstem-spinal Cord Preparations from Newborn Rodents Allows Neural Respiratory Network Output Recording

While it is well known that the central respiratory drive is located in the brainstem, several aspects of its basic function, development, and response to stimuli remain to be fully understood. To overcome the difficulty of accessing the brainstem in the whole animal, isolation of the brainstem and part of the spinal cord is performed. This preparation is maintained in artificial cerebro-spinal fluid where gases, concentrations, and temperature are controlled and monitored. The output signal from the respiratory network is recorded by a suction electrode placed on the fourth ventral root. In this manner, stimuli can be directly applied onto the brainstem, and the effect can be recorded directly. The signal recorded is linked to the inspiratory signal sent to the diaphragm via the phrenic nerve, and can be described as bursts (around 8 bursts per minute). Analysis of these bursts (frequency, amplitude, length, and area under the curve) allows precise characterization of the stimulus effect on the respiratory network. The main limitation of this method is the viability of the preparation beyond the early post-natal stages. Thus, this method greatly focuses on the study of the whole network without the peripheral inputs in the newborn rat.

The central respiratory drive is located in the brainstem. Spontaneous respiratory motor output from an isolated brainstem-spinal cord is recorded by placing an electrode on the fourth ventral root. This experimental approach is valuable for pharmacological investigations or the assessment of respiratory challenges and genetic manipulations on rhythmic motor behavior.

While it is well known that the central respiratory drive is located in the brainstem, several aspects of its basic function, development, and response to ...

Spiral Ganglion Neuron Explant Culture and Electrophysiology on Multi Electrode Arrays

Spiral ganglion neurons (SGNs) participate in the physiological process of hearing by relaying signals from sensory hair cells to the cochlear nucleus in the brain stem. Loss of hair cells is a major cause of sensory hearing loss. Prosthetic devices such as cochlear implants function by bypassing lost hair cells and directly stimulating SGNs electrically, allowing for restoration of hearing in deaf patients. The performance of these devices depends on the functionality of SGNs, the implantation procedure and on the distance between the electrodes and the auditory neurons. 
We hypothesized, that reducing the distance between the SGNs and the electrode array of the implant would allow for improved stimulation and frequency resolution, with the best results in a gapless position. Currently we lack in vitro culture systems to study, modify and optimize the interaction between auditory neurons and electrode arrays and characterize their electrophysiological response. To address these issues, we developed an in vitro bioassay using SGN cultures on a planar multi electrode array (MEA). With this method we were able to perform extracellular recording of the basal and electrically induced activity of a population of spiral ganglion neurons. We were also able to optimize stimulation protocols and analyze the response to electrical stimuli as a function of the electrode distance. This platform could also be used to optimize electrode features such as surface coatings.

We present a protocol to culture primary murine spiral ganglion neuron explants on multi electrode arrays to study neuronal response profiles and optimize stimulation parameters. Such studies aim to improve the neuron-electrode interface of cochlear implants to benefit hearing in patients as well as the energy consumption of the device.

Spiral ganglion neurons (SGNs) participate in the physiological process of hearing by relaying signals from sensory hair cells to the cochlear nucleus in ...

Prolonged Incubation of Acute Neuronal Tissue for Electrophysiology and Calcium-imaging

Acute neuronal tissue preparations, brain slices and retinal wholemount, can usually only be maintained for 6 - 8 h following dissection. This limits the experimental time, and increases the number of animals that are utilized per study. This limitation specifically impacts protocols such as calcium imaging that require prolonged pre-incubation with bath-applied dyes. Exponential bacterial growth within 3 - 4 h after slicing is tightly correlated with a decrease in tissue health. This study describes a method for&#160;limiting the proliferation of bacteria in acute preparations to maintain viable neuronal tissue for prolonged periods of time (&#62;24 h) without the need for antibiotics, sterile procedures, or tissue culture media containing growth factors. By cycling the extracellular fluid through UV irradiation and keeping the tissue in a custom holding chamber at 15 - 16 &#176;C, the tissue shows no difference in electrophysiological properties, or calcium signaling through intracellular calcium dyes at &#62;24 h postdissection. These methods will not only extend experimental time for those using acute neuronal tissue, but will reduce the number of animals required to complete experimental goals, and will set a gold standard for acute neuronal tissue incubation.

Once removed from the body, neuronal tissue is greatly affected by environmental conditions, leading to eventual degradation of the tissue after 6 - 8 h. Using a unique incubation method, which closely monitors and regulates the extracellular environment of the tissue, tissue viability can be significantly extended for &#62;24 h.

Acute neuronal tissue preparations, brain slices and retinal wholemount, can usually only be maintained for 6 - 8 h following dissection. This limits the ...