Optical Materialography Part 1: Sample Preparation

Vue d'ensemble

Source: Faisal Alamgir, School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA

The imaging of microscopic structures of solid materials, and the analysis of the structural components imaged, is known as materialography. Qualitative information such as, for example, whether or not there is porosity in the material, what the size and shape distribution of the grains look like, or whether there is anisotropy to the microstructure can be directly observed. We will see in Part 2 of the Materialography series, however, that statistical methods allow us to quantitatively measure these microstructural features and translate the analysis from a two-dimensional cross section to the three dimensional structure of a material sample.

This presentation will provide an overview of the techniques and procedures involved in preparing solid material samples for optical microscopy. While materialography can be conducted with optical as well as electron-based microscopy, this presentation will focus on the sample preparation specifically for optical microscopy. It should be noted, however, that a sample prepared for optical materialography can be used for scanning electron microscopy as well with minimum, if any, additional steps.

Procédure
  1. The sample examined in this video is a metal nut. First cut the sample normal to the hoop plane using a linear precision saw in order to isolate undamaged microstructural features for later viewing.
  2. Mount the specimen with the side to be imaged facing down on a mounting press. You must, of course, make sure that the sample is small enough to fit in the die cavity of the press, both laterally and vertically.
  3. Fill the remaining volume of the mounting press cavity with Bakelite, a thermosetting resin.
  4. Press

Log in or to access full content. Learn more about your institution’s access to JoVE content here

Résultats

From the series of images in Figure 1, particularly from the etched sample (Figure 1e), one can observe that the powder pressing process by which this sample was made rendered the grains to have non-circular, elongated shapes, with non-isotropic grain orientation. There is a significant amount of porosity retained in the material through this processing. Part 2 of the Materialography series will explore the statistics of the grai

Log in or to access full content. Learn more about your institution’s access to JoVE content here

Applications et Résumé

These are the standard methods for preparing cross sections of samples for microscopy. While the procedures detailed here are optimized to provide the best results in optical microscopy, some of the steps are unnecessary for scanning electron microscopy, and are inadequate for transmission electron microscopy. For the latter two, separate sample preparation procedures should be followed.

Materialographic sample preparation described here are the necessary first step towards the analysis of int

Log in or to access full content. Learn more about your institution’s access to JoVE content here

Tags
Optical MaterialographySample PreparationMicroscopic StructureSolid MaterialsPorosityGrainsIsotropyQualitative AnalysisQuantitative AnalysisProbing ToolLightElectron BeamCuttingMountingPolishingEtchingIsotropic MicrostructuresAnisotropic Samples

Passer à...

0:07

Overview

0:49

Principles of Sample Preparation for Optical Materialography

3:37

Protocol

6:11

Applications

7:09

Summary

Vidéos de cette collection:

article

Now Playing

Optical Materialography Part 1: Sample Preparation

Materials Engineering

15.3K Vues

article

Matérialographie optique II : Analyse d'image

Materials Engineering

10.9K Vues

article

Spectroscopie photoélectronique à rayons X

Materials Engineering

21.4K Vues

article

Diffraction des rayons X

Materials Engineering

87.6K Vues

article

Faisceaux d'ions focalisés

Materials Engineering

8.8K Vues

article

Solidification directionnelle et stabilisation de phase

Materials Engineering

6.5K Vues

article

Calorimétrie différentielle à balayage

Materials Engineering

36.3K Vues

article

Diffusivité thermique et méthode du flash laser

Materials Engineering

13.1K Vues

article

Dépôt électrolytique sur films minces

Materials Engineering

19.5K Vues

article

Analyse de la dilatation thermique par dilatométrie

Materials Engineering

15.5K Vues

article

Spectroscopie d'impédance électrochimique

Materials Engineering

22.9K Vues

article

Matériaux composites à matrice céramique et leurs propriétés de flexion

Materials Engineering

8.0K Vues

article

Alliages nanocristallins et stabilité de la taille des nano-grains

Materials Engineering

5.1K Vues

article

Synthèse des hydrogels

Materials Engineering

23.4K Vues

JoVE Logo

Confidentialité

Conditions d'utilisation

Politiques

Recherche

Enseignement

À PROPOS DE JoVE

Copyright © 2025 MyJoVE Corporation. Tous droits réservés.