setup and alignment of the laser speckle imaging (lsi) instrument with the 3d printer

3D 프린팅 품질 최적화를 위한 고분자 역학 시각화

The method of 3D printing is an additive manufacturing technique in which an object is manufactured layer by layer to form the desired shape. This method has a large and diverse user-base thanks to its versatility, affordability, and ease of use. Fused deposition modeling features a moving extruder (with a diameter of hundreds of microns to a couple of millimeters) to deposit molten plastic into the desired shape1. The extruded plastic should behave in a liquid-like manner for a certain duration to achieve good fusion with the previously printed plastic and form a strongly cohesive material. However, the plastic should cool down and solidify quickly after printing to prevent the plastic from flowing away from the print location and reducing the print quality. This delicate interplay between heating and cooling has been shown to directly underpin the balance between the mechanical strength and the geometric accuracy of the final 3D-printed object2. To achieve the optimal heating-cooling balance, the plastic is extruded at a temperature just above its melting temperature, and a fan head, attached to the printer, is used to cool the plastic down quickly. An in-depth understanding of the effects of printing temperatures and cooling speeds could provide the insights required for developing advanced slicing and printing protocols that maximize the mechanical or geometric results in the areas where they are most important. Efforts to gain more insight into these processes often rely on infrared (IR) imaging, which only visualizes the surface temperature3,4,5 and does not indicate the inner temperature of the plastic. Local heating beyond the melting transition drastically increases the polymer mobility and, thus, allows polymer entanglement between the old and new material. This temporally enhanced polymer motion is a requirement for the formation of the final cohesive material6,7, but IR imaging can only measure polymer motion indirectly through the surface temperature8,9. Translating the surface temperature to layer bonding thus necessitates precise knowledge of the core-surface temperature gradient and the associated complex polymer dynamics over a range of time and length scales. A direct measurement of the layer bonding (i.e., the polymer entanglement process) would allow the visualization of the mechanism underlying bulk material cohesion without a priori information or assumptions.
To gain an understanding of the spatial and temporal distribution of layer bonding, an imaging technique that directly quantifies the dynamics of the polymers that make up the plastic filament is employed in this work. This technique, laser speckle imaging (LSI), relies on interferometric light scattering to visualize nanoscopic motions, independent of the chemical composition. Depending on the optical properties of the sample, it can accurately measure several millimeters to centimeters into non-transparent materials10,11,12, unlike IR imaging, which reports only surface temperatures8,9. These attributes have recently made speckle-based methods popular in understanding dynamic processes in a plethora of materials, although they were originally developed for medical applications10,11,12. Recently, LSI has been used to gain insight into the behavior of advanced polymeric materials such as self-cleaning liquid crystal polymer networks13,14, as well as for predicting fracture in rubber15 and for studying self-healing materials16.
The feasibility of applying LSI to 3D printing was showcased in a previous article17, where a portable LSI setup with real-time analysis capabilities was presented, and it was shown that the deposition of molten plastic results in increased polymer motion multiple layers below the current layer. In the paper presented here, systematic research into the effects of the cooling fan speed on the degree of multi-layer bonding is performed. An improved plug-and-play version of the portable instrument is used that can be operated by users without optics or programming expertise. The speckle images are analyzed in real-time using Fourier transforms17, which visualize the amplitude of the speckle intensity fluctuations. This instrument has an additional brightfield camera that is aligned with the speckle camera so that the LSI motion maps can be overlayed with the brightfield images for easier interpretation without the brightfield light affecting the motion maps. The experimental approach presented in this article can be used to gain more insight into the melting, layer bonding, and solidification of extruded plastic during the 3D printing of challenging geometries and materials.

저자 스포트라이트: 3D 프린팅 레이어의 접착에 대한 실시간 이미징  

3D 프린팅 레이어의 결합에 대한 실시간 이미징

Our research aims to improve layer bonding during 3D printing. We use a method called laser speckle imaging to visualize the bonding process in real time. These insights will guide the optimization of printing conditions, hopefully leading to enhanced material design and performance.Currently, the layer bonding is studied using infrared imaging techniques that visualize this plastic*surface temperatures. To study layer bonding with infrared imaging, it is assumed that the inner temperature and the surface temperature is equal. Also, the complex relationship between temperature and the plastic fluidity has to be known.We've adapted laser speckle imaging for the use of 3D printing and have shown how to easily obtain deeper understanding of the layer bonding. Our LSI approach measures the polymer motion inside the plastic, visualizing the layer bonding without any assumptions. The technique is also non-invasive, easy to use, and has an excellent sensitivity.The method shown in this research can be used to study 3D prints or patterns that are challenging. The results can be used to understand how the setting should be changed to improve the print's quality.

Watch this Scientific Journal Video about Setup and Alignment of the Laser Speckle Imaging LSI Instrument with the 3D Printer at JoVE.com

Setup and Alignment of the Laser Speckle Imaging (LSI) Instrument with the 3D Printer  

3D 프린터와 레이저 스페클 이미징(LSI) 기기의 설정 및 정렬

진동을 최소화하기 위해 3D 프린터를 안정된 표면에 놓는 것부터 시작하십시오. 카메라가 인쇄 영역을 선명하게 볼 수 있도록 프린터 옆에 LSI 기기를 놓습니다. LSI를 카메라 빌드 플레이트보다 약간 높게 배치하고 아래쪽으로 약간 기울여 view 방해.그런 다음 레이저 및 명시야 조명을 켜고 이미징 영역과 정렬되어 있는지 확인합니다. 테스트 인쇄로 시작하여 LSI 카메라가 인쇄 영역에 초점이 맞춰져 있는지 확인합니다. 테스트 인쇄 중에 조명과 디지털 카메라를 최적으로 정렬하고 레이저 방향을 조정하여 전체 이미징 영역을 균일하게 비춥니다.스페클 크기가 픽셀 크기보다 약간 커지도록 다이어프램을 조정합니다. 실시간 LSI 데이터 분석을 위한 파라미터를 선택하고, 용융된 플라스틱과 응고된 플라스틱 간에 최상의 이미징 대비를 생성하는 주파수를 선택해야 합니다. 이미지 저장 빈도와 길이를 선택하여 LSI 기기가 이미지를 캡처할 수 있도록 준비합니다.

setup-alignment-laser-speckle-imaging-lsi-instrument-with-3d

Research

JoVE Journal

Engineering

Setup and Alignment of the Laser Speckle Imaging (LSI) Instrument with the 3D Printer

1.0K 조회수.  Wageningen University & Research. 진동을 최소화하기 위해 3D 프린터를 안정된 표면에 놓는 것부터 시작하십시오. 카메라가 인쇄 영역을 선명하게 볼 수 있도록 프린터 옆에 LSI 기기를 놓습니다. LSI를 카메라 빌드 플레이트보다 약간 높게 배치하고 아래쪽으로 약간 기울여 view 방해.그런 다음 레이저 및 명시야 조명을 켜고 이미징 영역과 정렬되어 있는지 확인합니다. 테스트 인쇄로 시작하여 LSI 카메라?...

비디오: Setup and Alignment of the Laser Speckle Imaging (LSI) Instrument with the 3D Printer  

Real-Time Imaging of Bonding in 3D-Printed Layers

In recent times, 3D printing technology has revolutionized our ability to design and produce products, but optimizing the print quality can be challenging. The process of extrusion 3D printing involves pressuring molten material through a thin nozzle and depositing it onto previously extruded material. This method relies on bonding between the consecutive layers to create a strong and visually appealing final product. This is no easy task, as many parameters, such as the nozzle temperature, layer thickness, and printing speed, must be fine-tuned to achieve optimal results. In this study, a method for visualizing the polymer dynamics during extrusion is presented, giving insight into the layer bonding process. Using laser speckle imaging, the plastic flow and fusion can be resolved non-invasively, internally, and with high spatiotemporal resolution. This measurement, which is easy to perform, provides an in-depth understanding of the underlying mechanics influencing the final print quality. This methodology was tested with a range of cooling fan speeds, and the results showed increased polymer motion with lower fan speeds and, thus, explained the poor printing quality when the cooling fan was turned off. These findings show that this methodology allows for optimizing the printing settings and understanding the material behavior. This information can be used for the development and testing of novel printing materials or advanced slicing procedures. With this approach, a deeper understanding of extrusion can be built to take 3D printing to the next level.

With a non-invasive and real-time technique, nanoscopic polymer motion inside a polymer filament is imaged during 3D printing. Fine-tuning this motion is crucial for producing constructs with optimal performance and appearance. This method reaches the core of plastic layer fusion, thus offering insights into optimal printing conditions and material design criteria.

In recent times, 3D printing technology has revolutionized our ability to design and produce products, but optimizing the print quality can be ...

연구

공학

Begin by placing the 3D printer on a steady surface to minimize vibrations. Place the LSI instrument next to the printer so that the camera has a clear view of the printing area. Position the LSI slightly higher than the camera build plate and tilt it downward slightly to prevent view obstruction.Next, turn on the laser and bright-field illumination and ensure that they are aligned with the imaging area. Start with a test print, making sure that the LSI camera is focused on the printing area. During the test print, optimally align the lighting and the digital camera and adjust the laser direction to illuminate the whole imaging area homogenously.Adjust the diaphragm so that the speckle size is slightly larger than the pixel size. Select the parameters for the live LSI data analysis, being sure to choose the frequency that produces the best imaging contrast between molten and solidified plastic. Choose the frequency and length of image saving to prepare the LSI instrument to capture images.

3D-Printing Setup and Real-Time Imaging of 3D-Printed Layer Bonding

Start by drawing the object using a 3D drawing software of choice and export the object as a dot SDL file. Next, import the dot SDL file into the slicing software and choose the printing settings. Press the slice button in the slicing software to obtain the layers and travel path of the print head.Save the resulting G-code and send it to the 3D printer. Now start the 3D printer and allow it to warm up. Start the LSI measurement when the plastic starts to extrude to prevent unnecessary data saving.Once the 3D printer is done printing, stop the LSI measurement. Load the resulting data into an image viewing software and visually inspect the printed object. Print quality of the object appeared good with the surface showing layer lines.LSI imaging showed increased polymer motion in the recently printed layers. The experiment when repeated with the cooling fan resulted in slower cooling of the plastic at 0%fan speed, causing poor visual print quality with irregular surface layer lines and blobs. The overall designed geometry was imperfectly reproduced with the windows and holes being deformed.LSI imaging indicated increased polymer motion throughout the whole object. Advanced data analysis for the comparative welding zones of six fan speeds showed peak profile positions at which the polymers were most mobile. The welding zone profiles for 40 to 100%cooling were nearly identical, while the zone for 0%cooling extended over the entire measured area.