1. Preparing Tools and Accessories
<ol>
	<li>Tip/funnel stoppers
	<ol>
		<li>Obtain two sponge plugs (the diameter of the plugs must be slightly larger than the internal diameter of the vials used to transfer flies). Make a hole in the centers of the sponge plugs with a heated electric soldering iron.</li>
		<li>Obtain two 1 mL pipette tips, cut one in half transversely with a sharp knife, and discard the pointed end. Then, cut 1.5 cm of the pointed end off the second pipette tip. Glue the remains of the two pipette tips together with an all-purpose adhesive to make an elongated pipette tip (Figure 1A).</li>
		<li>Insert a funnel and the elongated pipette tip into the sponge plugs to make a tip and funnel stopper (hereafter referred to as T- and F-stoppers) and cap the pipette tip with a 100 &#956;L microcentrifuge tube (Figure 1A). 
		NOTE: The length of the funnel stem must be greater than the height of the plug. If it is shorter than or equal to the height of the plug, then flies will escape from the stem opening. The end of the funnel stem should be situated at least 2 cm above the surface of the culture medium or the bottom of an empty vial. Small funnels (e.g., disk diameter &#60;60 mm) with small internal stem opening diameters (&#60;5 mm) are preferable. Either a glass or a plastic funnel can be used to make an F-stopper. However, plastic funnels are preferable for biology classes, as they break less readily than glass funnels.</li>
	</ol>
	</li>
	<li>Microdissecting needles 
	<ol>
		<li>Obtain mechanical pencils that feel comfortable in the hand and insect pins that match the diameters (e.g., 0.5 mm, 0.7 mm) of their lead refills.</li>
		<li>Cut the wide ends of the insect pins with a pair of pliers and file the cut flat. Replace the lead with the pins (Figure 1B). Press the click button and feed out 0.5&#8211;1 cm of a pin to conduct a dissection. Clean the pin and push it completely back into the pencil shaft after a dissection activity to make it safe for any person to handle. 
		NOTE: Microdissecting needles are useful not only in dissections of organs such as larval salivary glands but also in counting and sorting dead adult flies.</li>
	</ol>
	</li>
	<li>Hard icepacks 
	<ol>
		<li>Obtain several refreezable hard icepacks (large-sized icepacks are preferable). Figure 1C shows an icepacks that worked well, which measures 26.5 cm x 14.5 cm x 2.5 cm and has top and bottom sides that are completely flat.</li>
		<li>Cut medical gauze (nonsterile) into pieces that are slightly smaller than the cold surfaces of the icepacks they cover. For example, a piece of medical gauze slightly smaller than 26.5 cm x 14.5 cm is preferable to cover an icepack shown in Figure 1C. 
		NOTE: The necessary accessories for these chilling tools include: an ice box (we used a 25 cm x 15 cm x 15 cm foam box for one person and 37 cm x 28 cm x 20 cm box for more than one person), which is used to store crushed ice; a pair of fine-point tweezers, which are used to grab chilled flies by their wings and transfer them to a vial; a pair of protective work gloves, which are used to take chilled icepacks out of a -20 &#176;C freezer; and plastic film, which is used to cover the stage of a stereomicroscope.</li>
	</ol>
	</li>
	<li>Drosophila egg collection cage 
	NOTE: Ready-made Drosophila egg collection cages are available from many biotechnology companies11. Described here is a small acrylic bottle-shaped egg collection cage for 60 mm Petri dishes (Figure 1D left; the cage design is shown in the middle). It can be adapted for other Petri dish sizes (e.g., 100 mm, 35 mm). This allows the transfer of flies into or out of the cage with ease. A simple cage can be prepared as follows.
	<ol>
		<li>Use a snap cutter to cut a soft plastic drink bottle (500 mL, internal diameter ca. 65 mm) into an approximate 2:1 (pointed end:blunt end) ratio and discard the blunt end.</li>
		<li>Wrap a strip of card paper around an apple juice plate (internal diameter 60 mm) with adhesive tape [the apple juice plate is used to collect eggs (Figure 1E, right)].</li>
	</ol>
	</li>
	<li>Cordless tube brush driver
	<ol>
		<li>Obtain a cordless drill driver (max speed = 500 rpm).</li>
		<li>Obtain a tube brush that has bristles along its sides as well as its front. Ideally, the diameter of the brush should be slightly larger than the diameter of the culture vials that need to be cleaned. Cut the end of its handle so it can be inserted into the drill chuck (Figure 1D). 
		NOTE: The necessary accessories for these cleaning tools include stainless steel sponges and long cuff rubber gloves.</li>
	</ol>
	</li>
</ol>
2. Transferring Adult Flies from Vial A to Vial B
NOTE: Transferring adult flies from one vial to another is the most common practice conducted in Drosophila experiments [e.g., transferring flies from old culture (A) to fresh culture (B) or from a cross vial (A) to empty vial (B)] for anesthetizing. The protocol described here can be used for any adult fly transferring activities. Unless otherwise stated, this protocol is used to transfer flies from vial A to vial B throughout this paper.
<ol>
	<li>Check the stem of the funnel of an F-stopper and the pipette tip of a T-stopper carefully, then clear any flies that remain in the stoppers with a rubber air blower. This step is of paramount importance, especially when one set of T- and F-stoppers is used for the continuous transferring of different Drosophila lines.</li>
	<li>Tap down the flies in vial A and replace its plug with a T-stopper, then plug vial B with an F-stopper.</li>
	<li>Invert vial A over vial B, insert the pipette tip end of the T-stopper into the funnel opening of the F-stopper, knock the edge of inverted vial A to allow flies to slip out of the pipette tip and through the stem of the funnel, and drop into vial B. If any old food in vial A becomes less compact, it may drop when vial A is inverted and knocked. In such a situation, invert vial B over vial A and allow the flies to crawl up into vial B.</li>
	<li>Separate the T-stopper from the F-stopper. Cap the pipette tip end of the T-stopper with a 200 &#956;L microcentrifuge tube if the remaining flies in vial A need to be transferred to other vials momentarily; otherwise, remove the T-stopper and replug vial A. Remove the F-stopper and replug vial B.</li>
</ol>
3. Immobilizing Flies by Chilling
<ol>
	<li>Keep hard refreezable icepacks in a -20 &#176;C freezer for at least 24 h before use.</li>
	<li>Place a chilled, hard icepack at room temperature (RT) for 20 min. Slightly moisten a piece of non-aseptic medical gauze with some running water and allow it to closely cling to the surface of the icepack. The medical gauze can be reused in the next fly chilling. At the same time, chill an empty vial in crushed ice.</li>
	<li>Transfer adult flies that need to be immobilized into the chilled empty vial (CEV). When the two transfer vials are separated, cover the CEV with a Petri dish or a plug and knock the CEV against the crushed ice to tap all the flies in the CEV down to the bottom. Repeat this process several times until all flies are immobilized. The flies will be immobilized within 30 s. Next, place the CEV in the ice for 1 min. It is not advisable to transfer too many flies at one time for anesthetizing.</li>
	<li>Pour the chilled flies out onto the medical gauze that covers the ice pack. Spread out the overlapping flies with a paintbrush and make sure that each fly can be chilled by the cold surface of the icepack. If a chilled hard icepack swells slightly, place it on a towel and work on its flat side.</li>
	<li>Remove the stage clips from the stereomicroscope, cover the stage with a piece of plastic film, and put the icepack onto the stage. Turn on the top light (a cold light source is desirable), focus the stereomicroscope and move the icepack until the chilled flies can be seen clearly.</li>
</ol>
4. Killing Adult Flies for Counting, Sorting, or Discarding
<ol>
	<li>Transfer adult flies into an empty vial and cover it with a Petri dish.</li>
	<li>Invert the vial, heat it for 1 min + 20 s in a microwave oven, and allow the dead flies drop into the Petri dish.</li>
	<li>Put on protective work gloves and take the vial out of the microwave. Pour the dead flies onto a white paper card, count or examine the flies with a microdissecting needle under a stereomicroscope, and dispose of the fly bodies in a garbage can after observation.</li>
	<li>To kill unwanted flies, heat the flies for 2&#8211;3 min in a microwave oven, then tap the carcasses into a garbage can. 
	NOTE: It is not advisable to kill some wing mutant strains (e.g., wing length mutants) for examination, as it is difficult to judge from the carcasses if the wings extend beyond the tip of the abdomen, which is seen in wild-type flies.</li>
</ol>
5. Transferring Flies In/Out of Bottle-shaped Egg Collection Cage
NOTE: As mentioned above, T- and F-stoppers are used to transfer flies into and out of the egg collection cage. Flies do not need to be anesthetized throughout this process. Other details, such as preparing the apple juice medium, egg collection, and dechorionization, can be found in the literature12.
<ol>
	<li>Insert the egg collection cage into the apple juice plate or mount the apple juice plate to the cage made of a soft drink bottle. Seal the joint around the two components with a strip of paraffin film.</li>
	<li>Place as many flies as possible into the cage and replug the cage with a foam stopper after transferring the flies.</li>
	<li>To change the food for flies in the cage, transfer the flies in the cage to an empty vial.</li>
	<li>Replace the apple juice plate and reseal it, then transfer the flies from the vial back to the cage.</li>
	<li>When egg collection ends, transfer the flies into an empty vial and transfer them into culture vials.</li>
</ol>
6. Cleaning Glass Culture Vials
NOTE: Generally, an old culture vial contains live flies. In the protocol described here, these flies DO NOT need to be killed before cleaning unless they are transgenic flies.
<ol>
	<li>Remove any permanent marker ink from the glass culture vials with wet, stainless steel sponges.</li>
	<li>Soak the culture vials in running water.
	<ol>
		<li>Fill a laboratory sink with water, add liquid dishwashing soap into the water, and mix.</li>
		<li>Immerse the culture vials into the water, then remove the plug, allowing the water to run into the vial. The dish detergent in the water will make any remaining adult flies sink to the bottom and drown in the water.</li>
		<li>Soak the old culture vials in water for at least 30 min.</li>
	</ol>
	</li>
	<li>Loosen the chuck of the drill, insert the test tube brush and retighten the chuck. Check the direction of the rotation selector and ensure that the drill rotates clockwise. Adjust the speed trigger and ensure that the maximum speed is less than 500 rpm.</li>
	<li>Clean the culture vials.
	<ol>
		<li>Clean the culture vials roughly.
		<ol>
			<li>Put a long cuff rubber glove on the non-dominant hand and hold the vial in the water.</li>
			<li>Hold the cordless tube brush driver with the bare dominant hand, squeeze the brush into the culture vial, and squeeze the trigger. 
			NOTE: Do not dip the battery into the water. The rotating brush will break up old food, pupa, etc., and remove more than 95% of the waste.</li>
			<li>Dump the waste into a separate garbage can. Repeat this process until most of the waste in each vial has been cleaned.</li>
		</ol>
		</li>
		<li>Clean the culture vials thoroughly.
		<ol>
			<li>Clean the tube brush, drain and clean the sink, and refill it with clean water.</li>
			<li>Remove the remaining waste from each culture vial as described in section 6.4.1.</li>
		</ol>
		</li>
	</ol>
	</li>
</ol>

<ol>
	<li>Jennings, B. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Drosophila+&#8211;+a+versatile+model+in+biology+&#38;+medicine.">Drosophila &#8211; a versatile model in biology &#38; medicine.</a> Materials Today. 14 (5), 190-195 (2011).</li><li>JoVE Science Education Database. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Biology I: yeast, Drosophila and C. elegans. An Introduction to Drosophila melanogaster. , (2018).</li><li>Ashburner, M., Roote, J., Sullivan, W., Ashburner, M., Hawley, R. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Laboratory+Culture+of+Drosophila.">Laboratory Culture of Drosophila.</a> Drosophila Protocols. , (2000).</li><li>Greenspan, R. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fly+pushing:+The+theory+and+practice+of+Drosophila+genetics.">Fly pushing: The theory and practice of Drosophila genetics.</a> Cold Spring Harbor Laboratory Press. , (2004).</li><li>Ashburner, M., Thompson, J., Ashburner, M., Wright, T. R. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+laboratory+culture+of+Drosophila.">The laboratory culture of Drosophila.</a> The genetics and biology of Drosophila. 2a, 1-109 (1978).</li><li>Ratterman, D. M., O&#39;Donnell, M. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Eliminating+ether+by+using+ice+for+Drosophila+labs.">Eliminating ether by using ice for Drosophila labs.</a> Tested Studies For Laboratory Teaching. , 259-265 (2003).</li><li>. Culturing techniques for Drosophila Available from: <a target="_blank" href="https://www.ptbeach.com/cms/lib/NJ01000839/Centricity/Domain/113/ap%20biology%20Labs/Culturing%20techniques%20for%20Drosophila.pdf">https://www.ptbeach.com/cms/lib/NJ01000839/Centricity/Domain/113/ap%20biology%20Labs/Culturing%20techniques%20for%20Drosophila.pdf</a> (2019)</li><li>Markow, T. A., O&#39;Grady, P. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Drosophila: A Guide to Species Identification and Use. , (2006).</li><li>Artiss, T., Hughes, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Taking+the+Headaches+Out+of+Anesthetizing+Drosophila:+A+Cheap+&#38;+Easy+Method+of+Constructing+Carbon+Dioxide+Staging.">Taking the Headaches Out of Anesthetizing Drosophila: A Cheap &#38; Easy Method of Constructing Carbon Dioxide Staging.</a> The American Biology Teacher. 69 (8), e77-e80 (2007).</li><li>Qu, W. -. H., Zhu, T. -. B., Yang, D. -. X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Modified+Cooling+Method+and+its+Application+in+Drosophila+Experiments.">A Modified Cooling Method and its Application in Drosophila Experiments.</a> Journal Of Biological Education. 49 (3), 302-308 (2015).</li><li>. Egg-laying cages for drosophila Available from: <a target="_blank" href="https://www.kisker-biotech.com/frontoffice/product?produitId=0H-19-17">https://www.kisker-biotech.com/frontoffice/product?produitId=0H-19-17</a> (2018)</li><li>Roberts, D. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Drosophila: a practical approach. , (1998).</li><li>Tang, M., Peng, Q. -. F., Yang, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two+devices+for+Drosophila+experiments+(in+Chinese).">Two devices for Drosophila experiments (in Chinese).</a> Bulletin of Biology. 45 (11), 49-50 (2010).</li><li>Zhou, T. -. y., Gan, J., Yang, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Preparation+of+sponge+plug+and+sponge+plug+based+fly+transferring+device+for+Drosophila+experiments+(in+Chinese).">Preparation of sponge plug and sponge plug based fly transferring device for Drosophila experiments (in Chinese).</a> Bulletin of Biology. 46 (6), 49-50 (2011).</li><li>Yang, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Genetics laboratory investigation. , (2016).</li><li>Yang, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Carnivory+in+the+larvae+of+Drosophila+melanogaster+and+other+Drosophila+species.">Carnivory in the larvae of Drosophila melanogaster and other Drosophila species.</a> Scientific Reports. 8, (2018).</li><li>Stocker, H., Gallant, P., Dahmann, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Getting+Started:+An+Overview+on+Raising+and+Handling+Drosophila.">Getting Started: An Overview on Raising and Handling Drosophila.</a> Drosophila: Methods and Protocols. , (2008).</li></ol>

The author have nothing to disclose.

Some homemade tools for handling basic activities involved in Drosophila rearing and experimentation are described in this paper. These tools are simple but rather effective. Virtually, any lab can make these tools with ease, and a research or a teaching laboratory does not need to find a ready-made alternative that is perhaps not available locally.
Fly transferring is the most common practice and a difficult task in Drosophila experiments. Unfortunately, until now, there hav...

The fruit fly, Drosophila melanogaster, is a model organism widely used in biological research and biology education to study a wide range of topics1,2. The basic problems of handling Drosophila are the transfer of adults from vial to vial and immobilization of the flies so they are easier to handle, as all adults (except for some mutants3,4) can fly.
Conventionally, a researcher transfers flies from one vial to another by holding two vials mouth-to-mouth, tapping the flies down or allowing flies to fly up into another vial, then separating and replugging both vials4. Obviously, this requires that the opening of two vials with the same diameter, and it is hard to control the quantity of flies transferred. Meanwhile, this requires quick hands to get the job done, and escaping stray flies can result in problems for the laboratory or classroom. Adding extra virgin flies or male flies to an already prepared cross is another routine task in Drosophila experiments. Conventionally, flies must be immobilized in the cross vial before the addition of extra flies.
Adult Drosophila are routinely anaesthetized by ether, CO2, or chilling5. Compared to ether and CO2 exposure, chilling is the most cost-efficient agent for immobilizing adult Drosophila and the least harmful to both the flies and researchers (especially young students)6,7. However, water that condenses continuously on the cold surface or chamber wets the flies. It is difficult to determine the phenotypes of wet flies, and they can easily become damaged during manipulation8,9. This has kept the chilling method from becoming more widely accepted.
Tools for fly transferal and a method for fly cooling have been previously described10. Herein, a modified chilling anesthesia technique is reported that is safe, reliable, and feasible for Drosophila experiments. Also described in this paper are 1) methods for killing adults for counting, sorting, or discarding, 2) labor-saving devices and protocols for cleaning glass culture vials, and 3) a simple cage for collecting eggs. The easily designed and cost-effective tools described here can be used to address the difficult issues of fly handling, and these methods have been tested and are proven to be robust, reliable, and easy-to-handle for experienced and novice researchers.

<table><tbody><tr><td>A pair of pliers</td><td></td><td></td><td></td></tr><tr><td>Cordless drill driver</td><td></td><td></td><td>max speed: 500 rpm</td></tr><tr><td>Electric soldering iron</td><td></td><td></td><td></td></tr><tr><td>File</td><td></td><td></td><td></td></tr><tr><td>Funnel</td><td></td><td></td><td>diameter of disk&amp;lt;60mm</td></tr><tr><td>Ice box</td><td></td><td></td><td></td></tr><tr><td>Insect pins</td><td></td><td></td><td></td></tr><tr><td>Infrared thermometer</td><td></td><td></td><td>HCIYET HT-830</td></tr><tr><td>Long cuff rubber gloves</td><td></td><td></td><td></td></tr><tr><td>Mechanical pencils</td><td></td><td></td><td></td></tr><tr><td>Medical gauze</td><td></td><td></td><td></td></tr><tr><td>Microcentrifuge tube</td><td></td><td></td><td>100 ul</td></tr><tr><td>Microwave oven</td><td></td><td></td><td></td></tr><tr><td>Parafilm</td><td></td><td></td><td></td></tr><tr><td>Peri dish</td><td></td><td></td><td>internal diameter 60 mm</td></tr><tr><td>Pipette tips</td><td></td><td></td><td>1 ml</td></tr><tr><td>Plastic film</td><td></td><td></td><td></td></tr><tr><td>Plastic Peri dish</td><td></td><td></td><td>&amp;Phi;36 mm used to cover the empty vial</td></tr><tr><td>Point tweezers</td><td></td><td></td><td></td></tr><tr><td>Protective work gloves</td><td></td><td></td><td></td></tr><tr><td>Re-freezable hard icepacks</td><td></td><td></td><td>26.5&amp;times;14.5&amp;times;2.5 cm or larger</td></tr><tr><td>Rubber air blower</td><td></td><td></td><td></td></tr><tr><td>Snap cutter</td><td></td><td></td><td></td></tr><tr><td>Soft drink bottle</td><td></td><td></td><td>500 ml, internal diameter c.a. 65 mm</td></tr><tr><td>Sponge stopper</td><td></td><td></td><td></td></tr><tr><td>Stainless steel sponges</td><td></td><td></td><td></td></tr><tr><td>Tube brush</td><td></td><td></td><td></td></tr><tr><td>Vial</td><td></td><td></td><td>&amp;Phi;34 mm &amp;times; 90 mm</td></tr></tbody></table>

simple homemade tools to handle fruit flies&#8212;drosophila melanogaster

The fruit fly, Drosophila melanogaster, is widely used both in biological research and biology education. Handling adult flies is common but difficult in practice, as adult flies fly. Demonstrated here is how to make some simple and cost-effective tools to address difficult issues in the handling of Drosophila. Holes in foam stoppers are made and pipette tips or funnels are inserted into the holes. Flies then move only in one direction into the pipette tip/funnel assemblage, allowing efficient control of the transfer of adult Drosophila into or out of a vial. Existing protocols have been modified for cool-anesthetizing flies by chilling in crushed ice and transferring them onto a cold, hard icepack surface. The icepack is covered with a piece of medical gauze that keeps immobilized flies from the condensed water when examined under a stereomicroscope. The flies are finally euthanized for counting and sorting or discarded by microwaving. A bottle-shaped cage has also been developed for collecting eggs, as well as a labor-saving device and accompanying protocol for cleaning glass culture vials.

The T- and F-stoppers were developed as a set of simple tools that can be adapted and used in any fly transferring activities. Transferring flies from an old culture into several fresh cultures involves removing the plugs of the fresh vials, replacing them with F-stoppers, then tapping down the flies in the old vial, quickly removing its plug, and replacing it with a T-stopper. If the old food is compact, then it is important to flip the old vial and insert the tip of T-stopper into the o...

Watch this Scientific Journal Video about Simple Homemade Tools to Handle Fruit Fliesâ€”Drosophila melanogaster at JoVE.com

Simple Homemade Tools to Handle Fruit Flies&#8212;Drosophila melanogaster

Described here is the use of several homemade tools to transfer, chill, and kill adult Drosophila, as well as to clean glass culture vials and collect eggs. These tools are easy to make and are rather efficient in handling Drosophila.

The fruit fly, Drosophila melanogaster, is widely used both in biological research and biology education. Handling adult flies is common but difficult in ...

simple-homemade-tools-to-handle-fruit-fliesdrosophila-melanogaster

Research

JoVE Journal

Biology

15.9K Views.  China Agricultural University. Het kan een uitdaging zijn om fruitvliegjes over te brengen en te immobiliseren. Met behulp van deze technieken en tools u routinematige vliegoverdracht en immobilisatie eenvoudiger maken. De materialen die nodig zijn om deze tools te maken zijn goedkoop en gemakkelijk te verkrijgen.Advies- en onderwijs- of onderzoekslab kan ze met gemak maken. Gebruik voor het begin van deze procedure een elektrisch snikkend strijkijzer om een gat te maken in de centra van twee sponspluggen die groter...

Video: Simple Homemade Tools to Handle Fruit Flies—Drosophila melanogaster

Assaying Blood Cell Populations of the Drosophila melanogaster Larva

In vertebrates, hematopoiesis is regulated by inductive microenvironments (niches). Likewise, in the invertebrate model organism&#160;Drosophila melanogaster, inductive microenvironments known as larval Hematopoietic Pockets (HPs) have been identified as anatomical sites for the development and regulation of blood cells (hemocytes), in particular of the self-renewing macrophage lineage.&#160;HPs are segmentally repeated pockets between the epidermis and muscle layers of the larva, which also comprise sensory neurons of the peripheral nervous system. In the larva, resident (sessile) hemocytes are exposed to anti-apoptotic, adhesive and proliferative cues from these sensory neurons and potentially other components of the HPs, such as the lining muscle and epithelial layers. During normal development, gradual release of resident hemocytes from the HPs fuels the population of circulating hemocytes, which culminates in the release of most of the resident hemocytes at the beginning of metamorphosis. Immune assaults, physical injury or mechanical disturbance trigger the premature release of resident hemocytes into circulation. The switch of larval hemocytes between resident locations and circulation raises the need for a common standard/procedure to selectively isolate and quantify these two populations of blood cells from single Drosophila larvae. Accordingly, this protocol describes an automated method to release and quantify the resident and circulating hemocytes from single larvae. The method facilitates ex vivo approaches, and may be adapted to serve a variety of developmental stages of Drosophila and other invertebrate organisms.

Assaying Blood Cell Populations of the Drosophila melanogaster Larva

Drosophila blood cells, or hemocytes, cycle between resident sites and circulation. In the larva, resident (sessile) hemocytes localize to inductive microenvironments, the Hematopoietic Pockets, while circulating hemocytes move freely in the hemolymph. The goal of this protocol is the standardized isolation and quantification of these two, behaviorally distinct but interchanging, hemocyte populations.

In vertebrates, hematopoiesis is regulated by inductive microenvironments (niches). Likewise, in the invertebrate model organism&#160;Drosophila ...

Developmental Biology

A Direct and Simple Method to Assess Drosophila melanogaster's Viability from Embryo to Adult

In Drosophila melanogaster, viability assays are used to determine the fitness of certain genetic backgrounds. Allelic variations can result in partial or complete loss of viability at different stages of development. Our lab has developed a method to assess viability in Drosophila from embryo to fully mature adult. The method relies on quantifying the number of progeny present at different stages during development, starting with hatched embryos. After embryos have been quantified, additional stages are counted, including L1/L2, pupae, and mature adults. After all stages have been examined, a statistical analysis such as the chi-square test is used to determine if there is a significant difference between the starting number of progeny (hatched embryos) and later stages culminating in the observed number of adults, thus rejecting or accepting the null hypothesis (that the number of hatched embryos will be equal to the number of larvae, pupae, and adults recorded throughout the stages of development). The primary advantage of this assay is its simplicity and accuracy, as it does not require an embryo rinse to transfer them to the food vial, avoiding losses from technical errors. Although the protocol described here does not directly examine L2/L3 larvae, additional steps can be added to account for these. Comparing the number of hatched embryos, L1, pupae, and adults can help determine if viability was compromised during the L2/L3 stages for further studies (the use of colored food helps with visual identification of larvae). Overall, this method can help Drosophila researchers and educators determine when viability is compromised during the fly life cycle. Routine assessment of stocks using this assay can prevent accumulation of secondary mutations that may affect the phenotype of the originally isolated mutant, especially if the original mutations affect fitness. For this reason, our lab maintains multiple copies of each of our Dm ime4 alleles and routinely checks the purity of each stock with this method in addition to other molecular analyses.&#160;

A Direct and Simple Method to Assess Drosophila melanogaster's Viability from Embryo to Adult

This protocol is designed to assess the viability of Drosophila at every developmental stage, from embryo to adult. The method can be used to determine and compare the viability of different genotypes or growth conditions.

In Drosophila melanogaster, viability assays are used to determine the fitness of certain genetic backgrounds. Allelic variations can result in partial or ...

An Affordable and Efficient "Homemade" Platform for Drosophila Behavioral Studies, and an Accompanying Protocol for Larval Mitochondrial Respirometry

The usefulness of Drosophila as a model organism for the study of human diseases, behaviors and basic biology is unquestionable. Although practical, Drosophila research lacks popularity in developing countries, possibly due to the misinformed idea that establishing a lab and performing relevant experiments with such tiny insects is difficult and requires expensive, specialized apparatuses. Here, we describe how to build an affordable flylab to quantitatively analyze a myriad of behavioral parameters in D. melanogaster, by 3D-printing many of the necessary pieces of equipment. We provide protocols to build in-house vial racks, courtship arenas, apparatuses for locomotor assays, etc., to be used for general fly maintenance and to perform behavioral experiments using adult flies and larvae. We also provide protocols on how to use more sophisticated systems, such as a high resolution oxygraph, to measure mitochondrial oxygen consumption in larval samples, and show its association with behavioral changes in the larvae upon the xenotopic expression of the mitochondrial alternative oxidase (AOX). AOX increases larval activity and mitochondrial leak respiration, and accelerates development at low temperatures, which is consistent with a thermogenic role for the enzyme. We hope these protocols will inspire researchers, especially from developing countries, to use Drosophila to easily combine behavior and mitochondrial metabolism data, which may lead to information on genes and/or environmental conditions that may also regulate human physiology and disease states.

An Affordable and Efficient "Homemade" Platform for Drosophila Behavioral Studies, and an Accompanying Protocol for Larval Mitochondrial Respirometry

We provide protocols for anyone with a "maker culture" mind to start building a flylab for quantitative analysis of a myriad of behavioral parameters in Drosophila melanogaster, by 3D-printing many of the necessary pieces of equipment. We also describe a high resolution respirometry protocol using larvae to combine behavioral and mitochondrial metabolism data.

The usefulness of Drosophila as a model organism for the study of human diseases, behaviors and basic biology is unquestionable. Although practical, ...

Behavior

Retrograde Tracing of Drosophila Embryonic Motor Neurons Using Lipophilic Fluorescent Dyes

We describe a technique for retrograde labeling of motor neurons in Drosophila. We use an oil-dissolved lipophilic dye and deliver a small droplet to an embryonic fillet preparation by a microinjector. Each motor neuron whose membrane is contacted by the droplet can then be rapidly labeled. Individual motor neurons are continuously labeled, enabling fine structural details to be clearly visualized. Given that lipophilic dyes come in various colors, the technique also provides a means to get adjacent neurons labeled in multicolor. This tracing technique is therefore useful for studying neuronal morphogenesis and synaptic connectivity in the motor neuron system of Drosophila.

Retrograde Tracing of Drosophila Embryonic Motor Neurons Using Lipophilic Fluorescent Dyes

We describe a method for retrograde tracing of the Drosophila embryonic motor neurons using lipophilic fluorescent dyes.

We describe a technique for retrograde labeling of motor neurons in Drosophila. We use an oil-dissolved lipophilic dye and deliver a small droplet to an ...

A New Approach that Eliminates Handling for Studying Aggression and the "Loser" Effect in Drosophila melanogaster

Aggressive behavior in Drosophila melanogaster is composed of the sequential expression of stereotypical behavioral patterns (for analysis see 1). This complex behavior is influenced by genetic, hormonal and environmental factors. As in many organisms, previous fighting experience influences the fighting strategy of flies and the outcome of later contests: losing a fight increases the probability of losing later contests, revealing &#34;loser&#34; effects that likely involve learning and memory 2-4. The learning and memory that accompanies expression of complex social behaviors like aggression, is sensitive to pre-test handling of animals 5,6. Many experimental procedures are used in different laboratories to study aggression 7-9, however, no routinely used protocol that excludes handling of flies is currently available. Here, we report a new behavioral apparatus that eliminates handling of flies, using instead their innate negative geotactic responses to move animals into or out of fighting chambers. In this protocol, small circular fight arenas containing a food cup are divided into two equal halves by a removable plastic slider prior to introduction of flies. Flies enter chambers from their home isolation vials via sliding chamber doors and geotaxis. Upon removal of plastic sliders, flies are free to interact. After specified time periods, flies are separated again by sliders for subsequent experimentation. All of this is done easily without handling of individual flies. This apparatus offers a novel approach to study aggression and the associated learning and memory, including the formation of &#34;loser&#34; effects in fly fights. In addition, this new general-purpose behavioral apparatus can be employed to study other social behaviors of flies and should, in general, be of interest for investigating experience-related changes in fundamental behavioral processes.

A New Approach that Eliminates Handling for Studying Aggression and the "Loser" Effect in Drosophila melanogaster

During fruit fly fights, the behavioral patterns observed, fight dynamics, and associated learning and memory are influenced by experimental conditions. The protocol presented here describes a novel procedure that entirely eliminates handling of flies during experiments. This improves fight dynamics and allows formation of strong &#34;loser&#34; effects.

Aggressive behavior in Drosophila melanogaster is composed of the sequential expression of stereotypical behavioral patterns (for analysis see 1). This ...

Neuroscience

Maintenance of a Drosophila melanogaster Population Cage

Large quantities of DNA, RNA, proteins and other cellular components are often required for biochemistry and molecular biology experiments. The short life cycle of Drosophila enables collection of large quantities of material from embryos, larvae, pupae and adult flies, in a synchronized way, at a low economic cost. A major strategy for propagating large numbers of flies is the use of a fly population cage. This useful and common tool in the Drososphila community is an efficient way to regularly produce milligrams to tens of grams of embryos, depending on uniformity of developmental stage desired. While a population cage can be time consuming to set up, maintaining a cage over months takes much less time and enables rapid collection of biological material in a short period. This paper describes a detailed and flexible protocol for the maintenance of a Drosophila melanogaster population cage, starting with 1.5 g of harvested material from the previous cycle.

Maintenance of a Drosophila melanogaster Population Cage

This manuscript reports a detailed protocol for culturing, on a regular basis, a population of Drosophila melanogaster using a fly population cage.

Large quantities of DNA, RNA, proteins and other cellular components are often required for biochemistry and molecular biology experiments. The short life ...

High-Resolution Imaging and Analysis of Drosophila Eye Defects

A Rapid, Simple Workflow for Quantification of External Adult Drosophila Structures

The Drosophila compound eye is a precisely patterned tissue that has revealed molecular mechanisms and biological processes that drive morphogenesis. It is a simple structure of repeating unit eyes, termed ommatidia, that is used to characterize genetic interactions and gene functions. Mutations that affect eye architecture can be easily detected and analyzed; hence, this system is frequently used in under-resourced institutions. Further phenotypic analysis often includes a Scanning Electron Microscope (SEM) to generate high-magnification images suitable for quantitative analysis. However, SEMs are expensive and require costly reagents; sample preparation spans days; and, often, they need full-time staff for sample preparation and instrument maintenance. This limits their utility at under-resourced institutions or during budgetary austerity. In entomology, the use of high-resolution digital imaging technology is a common practice for the identification and characterization of species. This paper describes a method that combines strategies and allows for high-resolution digital imaging of adult Drosophila structures and quantitative analysis using the open software ImageJ. The workflow is a rapid and student-friendly alternative that remedies the limitations of underfunded and under-resourced research facilities with a cost-effective and rapid approach to quantitative phenotypic analysis.

Here, we present a rapid, low-cost, workflow for high-resolution imaging of adult Drosophila eyes to quantify patterning and growth defects. We describe our protocol for sample preparation by point-mounting, high-resolution image acquisition, and image analysis.

The Drosophila compound eye is a precisely patterned tissue that has revealed molecular mechanisms and biological processes that drive morphogenesis. It ...

Drosophila melanogaster Embryo and Larva Harvesting and Preparation

Drosophila melanogaster embryos and larvae are easy to manipulate and develop rapidly by mechanisms that are analogous to other organisms, including mammals. For these reasons, many researchers utilize fly embryos and larvae to answer questions in diverse fields ranging from behavioral to developmental biology. Prior to experimentation, however, the embryos and larvae must first be collected.
This video will first demonstrate how "egg-laying cups" are used to collect Drosophila embryos on agar plates. The harvest and dechorionation of embryos will then be described. Next, the video will demonstrate how to identify and manipulate Drosophila in one of the three larval stages that follow the embryo stage. Finally, examples of some of the ways in which fly embryos and larvae are used in biological research are provided.

Drosophila melanogaster Embryo and Larva Harvesting and Preparation

Drosophila melanogaster embryos and larvae are easy to manipulate and develop rapidly by mechanisms that are analogous to other organisms, including ...

Education

JoVE Science Education

Basic Biology

Biology I: yeast, Drosophila and C. elegans

Drosophila melanogaster Ovary Dissection: A Technique for Ex Vivo Tissue Preparation

Source: Parker, D. J., et al. <a href="https://www.jove.com/video/54989/" target="_blank">Studying Mitochondrial Structure and Function in Drosophila Ovaries</a>. J. Vis. Exp. (2017).
This video describes the general anatomy of the Drosophila&#160;ovary and features&#160;a method of dissecting ovaries for live or fixed imaging.

Source: Parker, D. J., et al. Studying Mitochondrial Structure and Function in Drosophila Ovaries. J. Vis. Exp. (2017).
This video describes the general ...

JoVE Encyclopedia of Experiments

Drosophila melanogaster (fruit fly)

Adult

Fly Aspirator Tube: A Simple Tool to Transfer Live Drosophila

Source: Barradale, F., et al. <a href="https://www.jove.com/video/55231/" target="_blank">Quantification of Drosophila Grooming Behavior</a>. J. Vis. Exp. (2017).
This video describes one method to build a fly aspirator, which can be used to transfer insects between enclosures without anesthesia. The aspirator in the example protocol was prepared for an experiment to quantify individual grooming behaviors

Simple Homemade Tools to Handle Fruit Flies—Drosophila melanogaster

Samenvatting

Meer video's verkennen