We thank all the members from our lab and Ophthalmic Animal Laboratory of Zhongshan Ophthalmic Center for their technical assistance. We also thank Prof. Chunqiao Liu for experimental support. This work was supported by grants from the National Natural Science Foundation of China (NSFC: 81670872; Beijing, China), the Natural Science Foundation of Guangdong Province, China (Grant No.2019A1515011347), and High-level hospital construction project from State Key Laboratory of Ophthalmology at Zhongshan Ophthalmic Center (Grant No. 303020103; Guangzhou, Guangdong Province, China).

All procedures involving the use of mice were approved by the animal experimental ethics committee of Zhongshan Ophthalmic Center, Sun Yat-sen University, China (authorized number: 2020-082), and in accordance with the approved guidelines of Animal Care and Use Committee of Zhongshan Ophthalmic Center and the Association Research in Vision and Ophthalmology (ARVO) Statement for the Use of Animals in Ophthalmic and Vision Research.
1. Induction of mouse OIR model
<ol>
	<li>Use mice with a lower rate of congenital malformation of the eyes, e.g., C57BL/6J mice, and mate them at a ratio of male/female = 1:2. Get the pups born on the same day and start to induce the OIR model at P7. Record the bodyweight of mouse pups strictly before modeling. 
	NOTE: Note the day of birth as P0. Record the weight of each mouse regularly. The bodyweight of newborn pups is very important during the induction of OIR as the sensitivity of mice in different states to oxygen is different. Exclude the pups more than 5 g at P7 to ensure comparable results.</li>
	<li>Provide a suitable living environment for nursing mothers and their pups, such as setting the temperature at 23 &#176;C &#177; 2 &#176;C, controlling the humidity at 40%-65%, alternating 12 h of light and 12 h of darkness every day, adding some cotton wool to the cage for nesting, ensuring adequate sterilized food and water, and keeping them in individually ventilated cages (IVC).</li>
	<li>Monitor the level of humidity and temperature inside the chamber. Control the humidity between 40% to 65% and keep the temperature at 23 &#176;C &#177; 2 &#176;C.</li>
	<li>Check the oxygen supply with oxygen sensors, maintain a constant oxygen level at 75% and control the oxygen flow rate at 0.5-0.75 L/min. Put 50 g soda lime at the bottom of the chamber to absorb excessive CO2 and maintain CO2 values below 3%22.</li>
	<li>Monitor the behaviors of nursing mothers such as nest-building behavior, biting their pups, and refusing lactation at least once a day. Eliminate nursing mothers with poor motherhood.</li>
	<li>Place the P7 pups (male and female) and their nursing mothers into an oxygen chamber in which the oxygen level is 75% for 5 days to P12. Avoid unnecessary opening of the chamber during the period of model induction. Ensure that there are extra surrogate mothers for replacement, in case the nursing mothers die due to lung injury while in hyperoxia. 
	NOTE: To ensure the comparability of the experiment, restrict the number to 6-8 pups for each mother. Pay attention to the potential problem of oxygen toxicity, which causes the death of some nursing mothers. The signs of hyperoxic lung injury in nursing mothers include, but are not limited to, fluctuating respiratory rate, decreased activity, and decreased feeding. When the above phenomenon occurs, euthanize the nursing mother with 1% pentobarbital sodium (50 mg/kg) as soon as possible. Prepare some surrogate mothers, e.g., 129S1/SvImJ for replacement and use them only if necessary. It is not recommended to replace nursing mothers as a routine, as this will lead to frequent opening of an oxygen chamber, resulting in unstable oxygen levels and maternal aggression.</li>
	<li>Bring the pups and their nursing mothers back to the room air at P12 and monitor the weight of all the pups continuously until P17. Group the pups based on the weight to ensure that each experimental group has a similar weight distribution.</li>
</ol>
2. Preparation of retinal whole mounts and immunofluorescence staining
<ol>
	<li>Record the bodyweight of the pups. Sacrifice the pups by an overdose of anesthetic (1% pentobarbital sodium 50 mg/kg) or CO2 inhalation. Other methods of euthanasia, such as cervical dislocation and bilateral thoracotomy, can be used if necessary.</li>
	<li>Use curved scissors to release the connection between eyeballs and orbital tissue. Then, put curved forceps into the posterior part of the eyeball, clamp the optic nerve, and quickly lift the eye out from the orbit. Wash the eyeballs in a pre-cooled 1x phosphate buffer saline (PBS) to remove the hair and blood from the surface of the eyeballs.</li>
	<li>Place the cleaned eyeballs in a 2 mL microcentrifuge tube filled with 4% paraformaldehyde (PFA) and incubate for 15 min at room temperature on a shaker at a speed of 12-15 revolutions per minute (rpm) (initial fixation). 
	CAUTION: Paraformaldehyde is known to be allergenic, generally toxic, and extremely cytotoxic. Follow the safety instructions strictly and avoid inhalation and skin contact.</li>
	<li>Use a culture dish and put a drop of 1x PBS into the central part and perform the following steps under a dissecting microscope and place one eyeball in this drop. Hold the eyeball with a pair of forceps and carefully puncture the cornea at the corneal limbus using a 1 mL syringe needle. Insert the tip of the scissors into this hole and cut off the cornea carefully along the cornea limbus. Be careful not to cut the retina.</li>
	<li>Remove the iris and lens with a pair of forceps. Then place the remaining eyecup in the 4% PFA and fix again for another 45 min at room temperature on a shaker at a speed of 12-15 rpm (secondary fixation).</li>
	<li>Use a culture dish and put a drop of 1x PBS into the central part. Place the fixed eyeball in this drop. Hold the eyeball with a pair of forceps. Gently separate the retina and sclera layers using two forceps. Place the tip of the scissors between the retina and sclera layers and cut the sclera toward the optic nerve. Peel the sclera off the retina and obtain the retinal cup. 
	NOTE: Hold the posterior cup by the optic nerve with forceps, then use the curved end of another forceps to press down on the sclera at the optic nerve head and gently massage out the retina in a forward sweeping motion as an alternative to release the retina.</li>
	<li>Use forceps to release the connection between radial hyaloid vessels and peripheral retina, clamp the root of the hyaloid vessels which is close to the optic nerve head, and cut the hyaloid vessels off carefully.</li>
	<li>Use a 2 mL pipette with the tip cut off to transfer the retinal cup. Place the retinal cup into one well in a 48-well plate and wash it for 3 x 5 min with 1x PBS at room temperature on a shaker at a speed of 12-15 rpm.</li>
	<li>Incubate the retinal cup in a mixed solution of 1% Triton X-100 (in PBS) and 5% normal donkey serum (in PBS) overnight at 4 &#176;C.
	<ol>
		<li>Alternatively, block and permeabilize retinas at room temperature for 1 h as an alternative. Change blocking serum according to the source of the secondary antibody.</li>
	</ol>
	</li>
	<li>If labeling the retinal vasculature using Isolectin B4, incubate the retina in a well of 48-well plate with 0.1% normal donkey serum (400 &#181;L) and IsolectinB4-594 (1:400) overnight at 4 &#176;C on a shaker at a speed of 12-15 rpm. 
	NOTE: If labeling the blood vessels with other markers, such as CD31, or labeling other cells, use specific primary antibodies to label them.</li>
	<li>Incubate the retina with 1:100-1:500 specific primary antibodies (in 400 &#181;L 0.1% normal donkey serum) at 4 &#176;C on a shaker at a speed of 12-15 rpm for 48 h. (optional)</li>
	<li>After returning to the room temperature, wash the retina with 0.1% PBST (0.1% TritonX-100 in PBS) for 3 x 20 min on a shaker at a speed of 12-15 rpm.</li>
	<li>Incubate the retina with 1:1,000 secondary antibodies (in 400 &#181;L 0.1% normal donkey serum) overnight at 4 &#176;C on a shaker at a speed of 12-15 rpm. (optional)
	<ol>
		<li>Alternatively, incubate the retina with high-affinity secondary antibodies at room temperature for 1 h.</li>
	</ol>
	</li>
	<li>Incubate the retina with DAPI (1:1,000) at room temperature for 20-25 min to label the nucleus. 
	NOTE: Test the optimal dilution ratios for all the antibodies used in steps 10-11 and 13-14 in pre-experiment.</li>
	<li>Wash the retina for 3 x 30 min with 0.1% PBST on a shaker at a speed of 12- 15 rpm at room temperature.</li>
	<li>Transfer the retinal cup to a clean slide with the opening facing upward. Cut the retina radially at the 3, 6, 9, and 12 o&#39;clock positions from peripheral to central by cutting approximately 1-1.5 mm away from the optic nerve head.</li>
	<li>Add a few drops of 1x PBS to rinse the retina three times. Use air-laid paper to dry and flatten the retina. Add a drop of mounting medium (see Table of Materials) to the center of the coverslip and stop adding it until the diameter of the droplet increases to half of the coverslip. Quickly turn over the coverslip and place it on top of the outspread retina. Avoid forming bubbles.</li>
	<li>Take images of the retinal flat mounts or store and protect the slides from light at 4 &#176;C.</li>
</ol>
3. Analysis and quantification of retinal flat mounts
NOTE: For the OIR mouse model, the researchers often record the area of central retinal vascular occlusion and peripheral retinal pathological neovascularization during P12-P25. Previous studies have shown that the central avascular area of the retina reaches the maximum at P12 and gradually shrinks from P13 to P17; at the same time, the retina of OIR mice reaches the peak of neovascularization area at around P1722,29. From P17, neovessels gradually regress and functional vessels regrow into the avascular area. The retinal vasculature basically returns to normal at P2533.
<ol>
	<li>Take images of retinal flat mounts by a fluorescence microscope (see Table of Materials) with 10x objective lens. First, choose the DAPI channel and set the optic nerve head in the center of the visual field. Then, adjust other channels and focus on the superficial vasculature of the retina. Check Tiles in a photo software (see Table of Materials) and set the number of photos that need to be stitched. Click on Start Experiment to capture the whole retina.</li>
	<li>Use an image processing program (see Table of Materials) to quantify the area of vaso-obliteration (VO) and neovascularization (NV) after immunofluorescence staining.
	<ol>
		<li>First, click on the Magic Wand Tool and set an appropriate tolerance according to the difference in brightness and move the cursor to the background and click the mouse. Then, choose the Select Inverse to obtain a basic outline of the retina. Use the Lasso Tool to further outline the details of the retina. Using the Histogram function, record the pixel value of the whole retina and write it down or generate a table in a database program.</li>
		<li>Divide the retina image into four quadrants. In each quadrant, use the Lasso Tool to draw the VO area (Figure 2A-C), and use the Magic Wand Tool to select the NV area (Figure 2D-F). Through the pixel information in the histogram, calculate the pixel ratio of VO and NV to the whole retina, that is, the percentage of VO or NV area relative to the whole retina. 
		NOTE: There is also an open-source and fully automated pipeline for the quantification of VO and NV areas in OIR images using deep learning neural networks (http://oirseg.org/),&#160;which provides a reliable and time-saving way for researchers as well as unifies the standard of the quantification34.</li>
	</ol>
	</li>
	<li>Record pixel information in a spreadsheet table, which is convenient for subsequent analysis.</li>
</ol>
4. In vivo imaging with fluorescein fundus angiography (FFA)
NOTE: For OIR mice, both FITC perfusion and immunofluorescence staining can only be used for one time because of the death of experimental animals. Compared with this, one of the advantages of FFA is the observation of the dynamic changes of mouse retinal vessels during development and pathological state in vivo35,36.
<ol>
	<li>Weigh the pups before anesthesia.</li>
	<li>Anesthetize pups by intraperitoneal injection of 0.3% pentobarbital sodium at a dose of 30-50 mg/kg. 
	NOTE: For mice within 1 month, pay attention to the anesthetic doses. Use lower concentrations and doses of anesthetic to reduce the death of mice caused by anesthesia. After the pups are anesthetized, use a small heating pad to maintain the body temperature. Hypothermia not only affects pups&#39; physiological function, but also leads to changes in crystallin and accelerates the development of cataracts.</li>
	<li>Use 20 &#181;L mydriatic eye drops (0.5% tropicamide + 0.5% phenylephrine hydrochloride) for each pup and wait for 5 min to achieve long-lasting pupil dilation (Figure 3A,B).</li>
	<li>Bring the anesthetized pups in front of the imaging device (see Table of Materials). Keep the pups on a small heating pad, place the pups in a stable position, and use artificial tears regularly to maintain moisture in the cornea. Click on the mode of Infrared Fundus Imaging (IR) to adjust the optic nerve head to the center of the screen.&#160; 
	NOTE: When observing one eye of the pups, do not forget to protect the other eye. Use Hypromellose eye drops to prevent the cornea from whitening due to dryness.</li>
	<li>After intraperitoneal injection of 0.15 mL 0.5% fluorescein sodium salt solution, click on the FA button and the Injection button immediately on the touch panel of the imaging device to start timing. Record the images after 3 min when the blood circulation of the retina enters the venous phase and observe the retina no less than 6-8 min. 
	NOTE: After intraperitoneal injection of fluorescein sodium salt solution, the skin, mucosa, and urine of the pups show obvious yellowish green. Most of the fluorescein is excreted by the pups within a day. Injecting the fluorescein sodium intraperitoneally every other day for six times does not cause significant side effects37.</li>
	<li>Move the optic nerve head to the center of the image acquisition area and take the first image of the central retina. Then, move the lens of the imaging device horizontally to the nasal side of the eye until the optic nerve head is located at the midpoint of one side of the image acquisition area and take the second image. Continue to take images of the temporal, superior and inferior retina, respectively using this method (Figure 3C). 
	NOTE: Take &#34;Five-orientation&#34; images within 12 min as the regression phase occurs. The position of the optic nerve head in the inferior image is allowed not to fall on the sideline due to the limited angle adjustment of the lens.</li>
	<li>Save the images and use an image processing program for stitching.</li>
</ol>
5. Image processing of the fluorescein fundus angiography (FFA)
<ol>
	<li>Open the imaging processing program and click on New in File to create a new canvas with a black background (Figure 4A).</li>
	<li>Open an image of the central retina first in the background layer. Click on File and add the second image. Adjust the opacity of the second image to 60%, move and resize the second image until the same parts of the two images highly overlap. Click on the Switch Between Free Transform and Warp Modes button and make subtle adjustments to the vessels if necessary. Then, turn the opacity of the second image back to 100% (Figure 4A,B).</li>
	<li>Select two images at the same time and click on Auto-Blend Layers. Check Panorama as the blend method as well as select the following two sentences. Click on OK and finish the image stitching of the first two images (Figure 4C,D).</li>
	<li>Take the first two stitched images as a whole, add the third image, and continue to blend. Repeat the methods above to complete the stitching of five images (Figure 4E).</li>
	<li>Use the Crop Tool to cut images of FFA at different time points to a uniform size and observe dynamic changes of retinal vasculature from P15 to P25 in both normal and OIR pups.</li>
</ol>
6. Statistical analysis
<ol>
	<li>Present values as mean &#177; standard deviation (s.d.).</li>
	<li>Use the Student&#39;s t-test to compare two independent samples. Use One-Way ANOVA to compare multiple sets of data and combine with Dunnett or Tukey&#39;s test, which is a commonly used multiple comparison test.</li>
	<li>For non-normally distributed data, use Mann-Whitney U test or Kruskal Wallis test. Consider significant statistical differences when P &#60; 0.05.</li>
</ol>

The authors have nothing to disclose.

The susceptibility of mice to OIR is affected by many factors. The pups of different genetic background and strains cannot be compared. In BALB/c albino mice, vessels regrow into the VO area rapidly with significant reduced neovascular tufts38, which bring some difficulties to the research. In C57BL/6 mice, there is increased photoreceptor damage when compared to BALB/cJ mouse strain39,40. The same goes for different types of transgenic mi...

Retinal neovascularization (RNV), which is defined as a state where new pathologic vessels originate from existing retinal veins, usually extends along the inner surface of the retina and grows into the vitreous (or subretinal space under some conditions)1. It is a hallmark and common feature of many ischemic retinopathies, including retinopathy of prematurity (ROP), retinal vein occlusion (RVO), and proliferative diabetic retinopathy (PDR)2.
Numerous clinical and experimental observations have indicated that ischemia is the main cause of retinal neovascularization3,4. In ROP, neonates are exposed to high-level oxygen in closed incubators to increase the survival rates, which is also an important driver for the arrest of vascular growth. After the treatment is done, the retinas of newborns experience a relatively hypoxic period5. Other situations are seen in the occlusion of central or branch retinal veins in RVO and damage of retinal capillaries is also observed which is caused by microangiopathy in PDR2. Hypoxia further increases the expression of angiogenic factors such as vascular endothelial growth factor (VEGF) through the hypoxia-induced factor-1&#945; (HIF-1&#945;) signaling pathway which in turn guide vascular endothelial cells to grow into the hypoxic area and form new vessels6,7.
ROP is a kind of vascular proliferative retinopathy in preterm infants and a leading cause of childhood blindness8,9, which is characterized by retinal hypoxia, retinal neovascularization and fibrous hyperplasia10,11,12. In the 1950s, researchers found that high concentration of oxygen can significantly improve the respiratory symptoms of premature infants13,14. As a result, oxygen therapy was increasingly used in premature infants at that time15. However, concurrent with the widespread use of oxygen therapy in preterm infants, the incidence of ROP increased year by year. Since then, researchers have linked oxygen to ROP, exploring various animal models to understand the pathogenesis of ROP and RNV16.
In human, most retinal vasculature development is completed before birth while in rodents the retinal vasculature develops after birth, providing an accessible model system to study angiogenesis in the retinal vasculature2. With the continuous progress of the research, oxygen-induced retinopathy (OIR) models have become major models for mimicking pathological angiogenesis resulting from ischemia. There are no specific animal species in the study of the OIR model and the model has been developed in various animal species, including kitten17, rat18, mouse19, beagle puppy20, and zebrafish21. All of the models share the same mechanism by which they are exposed to hyperoxia during early retinal development and then returned to the normoxic environment. Smith et al. observed that exposing mouse pups to hyperoxia from P7 for 5 days induced an extreme form of vessel regression in the central retina and bringing them back to the room air at P12 gradually triggered neovascular tufts, which grew toward the vitreous body19. This was a standardized OIR mouse model also named as Smith model. Connor et al. further optimized the protocol and provided a universally applicable method to quantify the area of VO (vaso-obliteration) and NV (neovascularization) in 2009, which increased the acceptance and utilization of the model22. OIR mouse model is still the most widely used model now because of its small size, fast reproduction, clear genetic background, good repeatability, and high success rate.
In mice, retinal vascularization starts after birth with the ingrowth of vessels from the optic nerve head into the inner retina toward the ora serrata. During normal retinal development, the first retinal vessels sprout from the optic nerve head around birth, forming an expanding network (the primary plexus) that reaches the periphery around postnatal day 7(P7)23. Then the vessels start to grow into the retina to form a deep layer, penetrate the retina, and establish a laminar network around the inner nuclear layer (INL) as in human24. By the end of the third postnatal week (P21), deeper plexus development is almost completed. For the OIR mouse model, vascular occlusion always appears in the central retina because of the rapid degeneration of a large number of immature vascular networks in the central region during hyperoxia exposure. So, the growth of pathological neovascularization also occurs in the mid-peripheral retina, which is the boundary of the non-perfusion area and the vascular area. However, human retinal vessels have almost formed before birth. As for premature infants, the peripheral retina is not completely vascularized when exposed to hyperoxia25,26. So vascular occlusion and neovascularization mainly appear in the peripheral retina27,28. Despite these differences, the mouse OIR model closely recapitulates the pathologic events that occur during ischemia-induced neovascularization.
The induction of the OIR model can be divided into two phases29: in phase 1 (hyperoxia phase), retinal vascular development is arrested or retarded with occlusion and regression of blood vessels as a result of the decline in VEGF and the apoptosis of endothelial cells24,30; in phase 2 (hypoxia phase), the retinal oxygen supply will become insufficient under room air conditions29, which is essential for neural development and homeostasis19,31. This ischemic situation usually results in unregulated, abnormal neovascularization.
Currently, the commonly used modeling method is alternating high/low oxygen exposure: Mothers and their pups are exposed to 75% oxygen for 5 days at P7 followed by 5 days in room air till P17 demonstrated comparable results22, which is the endpoint of OIR mouse model induction. (Figure 1). In addition to simulating ROP, this ischemia-mediated pathological neovascularization can also be used to study other ischemic retinal diseases. The main measurements of this model include quantifying the area of VO and NV, which are analyzed from retinal flat mounts by immunofluorescence staining or FITC-dextran perfusion. Each mouse can be studied only once because of the lethal operation. At present, there are few methods to observe dynamic changes of retinal vasculature continuously during the process of vascular regression and pathologic angiogenesis32. In this paper, we provide a detailed protocol of OIR model induction, analysis of retinal flat mounts as well as a workflow of fluorescein fundus angiography (FFA) on mice which would be helpful to gain a more comprehensive understanding of vascular dynamic changes during two phases of the OIR mouse model.

<table><tbody><tr><td>1 mL sterile syringe</td><td>Solarbio</td><td>YA0550</td><td>For preparation of retinal flat mounts and intraperitoneal injection</td></tr><tr><td>1&amp;times; Phosphate buffered saline (PBS)</td><td>Transgen Biotech</td><td>&amp;nbsp;FG701-01</td><td>For preparation of retinal flat mounts</td></tr><tr><td>2 ml Microcentrifuge Tube</td><td>Corning</td><td>MCT-200-C</td><td>For preparation of retinal flat mounts</td></tr><tr><td>48 Well Clear TC-Treated Multiple Well Plates</td><td>Corning</td><td>3548</td><td>For preparation of retinal flat mounts</td></tr><tr><td>Adhesive microscope slides</td><td>Various</td><td></td><td>For preparation of retinal flat mounts</td></tr><tr><td>Adobe Photoshop CC 2019</td><td>Adobe Inc.</td><td></td><td>For image analysis</td></tr><tr><td>Carbon dioxide gas</td><td>Various</td><td></td><td>For sacrifice</td></tr><tr><td>Cover slide</td><td>Various</td><td></td><td>For preparation of retinal flat mounts</td></tr><tr><td>Curved forceps</td><td>World Precision Instruments</td><td>14127</td><td>For preparation of retinal flat mounts</td></tr><tr><td>DAPI staining solution</td><td>Abcam</td><td>ab228549</td><td>For labeling nucleus on retinal flat mounts</td></tr><tr><td>Dissecting microscope</td><td>Olmpus</td><td>SZ61</td><td>For preparation of retinal flat mounts</td></tr><tr><td>Fluorescein sodium</td><td>Sigma-Aldrich</td><td>F6377</td><td>For &lt;em&gt;in vivo&lt;/em&gt; imaging</td></tr><tr><td>Fluorescent Microscope</td><td>&amp;nbsp;Zeiss</td><td>AxioImager.Z2</td><td>For acquisition of fluorescence images of retinal flat mounts</td></tr><tr><td>Fluoromount-G Mounting media</td><td>SouthernBiotech</td><td>&amp;nbsp;0100-01</td><td>For preparation of retinal flat mounts</td></tr><tr><td>Hydroxypropyl Methylcellulose</td><td>Maya</td><td>89161</td><td>For &lt;em&gt;in vivo&lt;/em&gt; imaging</td></tr><tr><td>Isolectin B4 594 antibody</td><td>Invitrogen</td><td>I21413</td><td>For labeling retinal vasculature on retinal flat mounts</td></tr><tr><td>Mice C57/BL6J</td><td>GemPharmatech of Jiangsu Province</td><td></td><td>For OIR model induction</td></tr><tr><td>Micro dissecting scissors-straight blade</td><td>World Precision Instruments</td><td>503242</td><td>For preparation of retinal flat mounts</td></tr><tr><td>No.4 straight forceps</td><td>World Precision Instruments</td><td>&amp;nbsp;501978-6</td><td>For preparation of retinal flat mounts</td></tr><tr><td>Normal donkey serum</td><td>Abcam</td><td>ab7475</td><td>For preparation of retinal flat mounts</td></tr><tr><td>O&lt;sub&gt;2&lt;/sub&gt; sensor</td><td>Various</td><td></td><td>For monitoring the level of O&lt;sub&gt;2&lt;/sub&gt;</td></tr><tr><td>OxyCycler</td><td>Biospherix</td><td>A84XOV</td><td>For OIR model induction</td></tr><tr><td>Paraformaldehyde (PFA)</td><td>Sigma</td><td>P6148-1KG</td><td>For tissue fixation</td></tr><tr><td>Pentobarbital sodium</td><td>Various</td><td></td><td>For anesthesia</td></tr><tr><td>Soda lime</td><td>Various</td><td></td><td>For absorbing excess CO&lt;sub&gt;2&lt;/sub&gt; in the oxygen chamber</td></tr><tr><td>SPECTRALIS HRA+OCT</td><td>Heidelberg</td><td>HC00500002</td><td>For &lt;em&gt;in vivo&lt;/em&gt; imaging</td></tr><tr><td>SPSS Statistics 22.0</td><td>IBM</td><td></td><td>For statistical analysis</td></tr><tr><td>Tansference decloring shaker</td><td>Kylin-Bell</td><td>ZD-2008</td><td>For preparation of retinal flat mounts</td></tr><tr><td>Tissue culture dish (Low attachment)</td><td>Corning</td><td>3261-20EA</td><td>For preparation of retinal flat mounts</td></tr><tr><td>Transfer pipettes</td><td>Various</td><td></td><td>For preparation of retinal flat mounts</td></tr><tr><td>Triton X-100</td><td>Sigma-Aldrich</td><td>&amp;nbsp;SLBW6818</td><td>For preparation of retinal flat mounts</td></tr><tr><td>Tropicamide</td><td>Various</td><td></td><td>For &lt;em&gt;in vivo&lt;/em&gt; imaging</td></tr><tr><td>ZEN Imaging Software</td><td>ZEISS</td><td></td><td>For image acquisition and export</td></tr></tbody></table>

monitoring dynamic growth of retinal vessels in oxygen-induced retinopathy mouse model

Oxygen-induced retinopathy (OIR) is widely used to study abnormal vessel growth in ischemic retinal diseases, including retinopathy of prematurity (ROP), proliferative diabetic retinopathy (PDR), and retinal vein occlusion (RVO). Most OIR studies observe retinal neovascularization at specific time points; however, the dynamic vessel growth in live mice along a time course, which is essential for understanding the OIR-related vessel diseases, has been understudied. Here, we describe a step-by-step protocol for the induction of the OIR mouse model, highlighting the potential pitfalls, and providing an improved method to quickly quantify areas of vaso-obliteration (VO) and neovascularization (NV) using immunofluorescence staining. More importantly, we monitored vessel regrowth in live mice from P15 to P25 by performing fluorescein fundus angiography (FFA) in the OIR mouse model. The application of FFA to the OIR mouse model allows us to observe the remodeling process during vessel regrowth.

In the OIR mouse model, the most important and basic result is the quantification of the VO and NV area. After living in the hyperoxia environment for 5 days from P7, the central retina of the pups showed the largest non-perfusion area. Under the stimulation of hypoxia in another 5 days, retinal neovascularization was gradually produced which fluoresced more intensely than surrounding normal vessels. After P17, the fluorescence signal of pathological neovascularization regressed rapidly as the remodeling of the retina (<...

Watch this Scientific Journal Video about Monitoring Dynamic Growth of Retinal Vessels in Oxygen-Induced Retinopathy Mouse Model at JoVE.com

Monitoring Dynamic Growth of Retinal Vessels in Oxygen-Induced Retinopathy Mouse Model

This protocol describes a detailed method for the preparation and immunofluorescence staining of mice retinal flat mounts and analysis. The use of fluorescein fundus angiography (FFA) for mice pups and image processing are described in detail as well.

Oxygen-induced retinopathy (OIR) is widely used to study abnormal vessel growth in ischemic retinal diseases, including retinopathy of prematurity (ROP), ...

monitoring-dynamic-growth-retinal-vessels-oxygen-induced-retinopathy

Research

JoVE Journal

Biology

3.4K Views.  Sun Yat-Sen University. Dit protocol kan onderzoekers helpen de netvliezen van muizen gemakkelijk te scheiden en de dynamische veranderingen in de retinale vasculatuur van het OIR-muismodel te observeren. De belangrijkste voordelen van deze methode zijn het behoud van de integriteit van de gescheiden netvliezen en het toestaan van elke muis om als zijn eigen controle te dienen, waardoor de resultaten meer vergelijkbaar zijn. Onderzoekers die deze methode voor de eerste keer proberen, kunnen moeite hebben tijdens het...

Video: Monitoring Dynamic Growth of Retinal Vessels in Oxygen-Induced Retinopathy Mouse Model

Trypsin Digest Protocol to Analyze the Retinal Vasculature of a Mouse Model

Trypsin digest is the gold standard method to analyze the retinal vasculature 1-5. It allows visualization of the entire network of complex three-dimensional retinal blood vessels and capillaries by creating a two-dimensional flat-mount of the interconnected vascular channels after digestion of the non-vascular components of the retina. This allows one to study various pathologic vascular changes, such as microaneurysms, capillary degeneration, and abnormal endothelial to pericyte ratios. However, the method is technically challenging, especially in mice, which have become the most widely available animal model to study the retina because of the ease of genetic manipulations 6,7. In the mouse eye, it is particularly difficult to completely remove the non-vascular components while maintaining the overall architecture of the retinal blood vessels. To date, there is a dearth of literature that describes the trypsin digest technique in detail in the mouse. This manuscript provides a detailed step-by-step methodology of the trypsin digest in mouse retina, while also providing tips on troubleshooting difficult steps.

Trypsin digest is one of the most commonly used methods to analyze retinal vasculature. This manuscript describes the method in detail, including key alterations to optimize the technique and remove the non-vascular tissue while preserving the overall architecture of the vessels.

Trypsin digest is the gold standard method to analyze the retinal vasculature 1-5. It allows visualization of the entire network of complex ...

Neuroscience

Intravital Video Microscopy Measurements of Retinal Blood Flow in Mice

Alterations in retinal blood flow can contribute to, or be a consequence of, ocular disease and visual dysfunction. Therefore, quantitation of altered perfusion can aid research into the mechanisms of retinal pathologies. Intravital video microscopy of fluorescent tracers can be used to measure vascular diameters and bloodstream velocities of the retinal vasculature, specifically the arterioles branching from the central retinal artery and of the venules leading into the central retinal vein. Blood flow rates can be calculated from the diameters and velocities, with the summation of arteriolar flow, and separately venular flow, providing values of total retinal blood flow. This paper and associated video describe the methods for applying this technique to mice, which includes 1) the preparation of the eye for intravital microscopy of the anesthetized animal, 2) the intravenous infusion of fluorescent microspheres to measure bloodstream velocity, 3) the intravenous infusion of a high molecular weight fluorescent dextran, to aid the microscopic visualization of the retinal microvasculature, 4) the use of a digital microscope camera to obtain videos of the perfused retina, and 5) the use of image processing software to analyze the video. The same techniques can be used for measuring retinal blood flow rates in rats.

Intravital microscopy can be used in animals to visualize and measure retinal vascular diameters, bloodstream velocities, and total retinal blood flow.

Alterations in retinal blood flow can contribute to, or be a consequence of, ocular disease and visual dysfunction. Therefore, quantitation of altered ...

Medicine

Assessment of Vascular Regeneration in the CNS Using the Mouse Retina

The rodent retina is perhaps the most accessible mammalian system in which to investigate neurovascular interplay within the central nervous system (CNS). It is increasingly being recognized that several neurodegenerative diseases such as Alzheimer&#8217;s, multiple sclerosis, and amyotrophic lateral sclerosis present elements of vascular compromise. In addition, the most prominent causes of blindness in pediatric and working age populations (retinopathy of prematurity and diabetic retinopathy, respectively) are characterized by vascular degeneration and failure of physiological vascular regrowth. The aim of this technical paper is to provide a detailed protocol to study CNS vascular regeneration in the retina. The method can be employed to elucidate molecular mechanisms that lead to failure of vascular growth after ischemic injury. In addition, potential therapeutic modalities to accelerate and restore healthy vascular plexuses can be explored. Findings obtained using the described approach may provide therapeutic avenues for ischemic retinopathies such as that of diabetes or prematurity and possibly benefit other vascular disorders of the CNS.

The rodent retina has long been recognized as an accessible window to the brain. In this technical paper we provide a protocol that employs the mouse model of oxygen-induced retinopathy to study the mechanisms that lead to failure of vascular regeneration within the central nervous system after ischemic injury. The described system can also be harnessed to explore strategies to promote regrowth of functional blood vessels within the retina and CNS.

The rodent retina is perhaps the most accessible mammalian system in which to investigate neurovascular interplay within the central nervous system (CNS). ...

Preparation Steps for Measurement of Reactivity in Mouse Retinal Arterioles Ex Vivo

Vascular insufficiency and alterations in normal retinal perfusion are among the major factors for the pathogenesis of various sight-threatening ocular diseases, such as diabetic retinopathy, hypertensive retinopathy, and possibly glaucoma. Therefore, retinal microvascular preparations are pivotal tools for physiological and pharmacological studies to delineate the underlying pathophysiological mechanisms and to design therapies for the diseases. Despite the wide use of mouse models in ophthalmic research, studies on retinal vascular reactivity are scarce in this species. A major reason for this discrepancy is the challenging isolation procedures owing to the small size of these retinal blood vessels, which is ~ &#8804; 30 &#181;m in luminal diameter. To circumvent the problem of direct isolation of these retinal microvessels for functional studies, we established an isolation and preparation technique that enables ex vivo studies of mouse retinal vasoactivity under near-physiological conditions. Although the present experimental preparations will specifically refer to the mouse retinal arterioles, this methodology can readily be employed to microvessels from rats.

Preparation Steps for Measurement of Reactivity in Mouse Retinal Arterioles Ex Vivo

Many vision-threatening ocular diseases are associated with dysfunctional retinal microvessels. Therefore, the measurement of retinal arteriole responses is important to investigate the underlying pathophysiological mechanisms. This article describes a detailed protocol for mouse retinal arteriole isolation and preparation to assess the effects of vasoactive substances on vascular diameter.

Vascular insufficiency and alterations in normal retinal perfusion are among the major factors for the pathogenesis of various sight-threatening ocular ...

Retinal Vascular Reactivity as Assessed by Optical Coherence Tomography Angiography

The vascular supply to the retina has been shown to dynamically adapt through vasoconstriction and vasodilation to accommodate the metabolic demands of the retina. This process, referred to as retinal vascular reactivity (RVR), is mediated by neurovascular coupling, which is impaired very early in retinal vascular diseases such as diabetic retinopathy. Therefore, a clinically feasible method of assessing vascular function may be of significant interest in both research and clinical settings. Recently, in vivo imaging of the retinal vasculature at the capillary level has been made possible by the FDA approval of optical coherence tomography angiography (OCTA), a noninvasive, minimal risk and dyeless angiography method with capillary level resolution. Concurrently, physiological and pathological changes in RVR have been shown by several investigators. The method shown in this manuscript is designed to investigate RVR using OCTA with no need for alterations to the clinical imaging procedures or device. It demonstrates real time imaging of the retina and retinal vasculature during exposure to hypercapnic or hyperoxic conditions. The exam is easily performed with two personnel in under 30 min with minimal subject discomfort or risk. This method is adaptable to other ophthalmic imaging devices and the applications may vary based on the composition of the gas mixture and patient population. A strength of this method is that it allows for an investigation of retinal vascular function at the capillary level in human subjects in vivo. Limitations of this method are largely those of OCTA and other retinal imaging methods including imaging artifacts and a restricted dynamic range. The results obtained from the method are OCT and OCTA images of the retina. These images are amenable to any analysis that is possible on commercially available OCT or OCTA devices. The general method, however, can be adapted to any form of ophthalmic imaging.

This article describes a method for measuring retinal vasculature reactivity in vivo with human subjects using a gas breathing provocation technique to deliver vasoactive stimuli while acquiring retinal images.

The vascular supply to the retina has been shown to dynamically adapt through vasoconstriction and vasodilation to accommodate the metabolic demands of ...

Optimization of the Retinal Vein Occlusion Mouse Model to Limit Variability

Mouse models of retinal vein occlusion (RVO) are often used in ophthalmology to study hypoxic-ischemic injury in the neural retina. In this report, a detailed method pointing out critical steps is provided with recommendations for optimization to achieve consistently successful occlusion rates across different genetically modified mouse strains. The RVO mouse model consists primarily of the intravenous administration of a photosensitizer dye followed by laser photocoagulation using a retinal imaging microscope attached to an ophthalmic guided laser. Three variables were identified as determinants of occlusion consistency. By adjusting the wait time after rose bengal administration and balancing the baseline and experimental laser output, the variability across experiments can be limited and a higher success rate of occlusions achieved. This method can be used to study retinal diseases that are characterized by retinal edema and hypoxic-ischemic injury. Additionally, as this model induces vascular injury, it can also be applied to study the neurovasculature, neuronal death, and inflammation.

Here, we describe an optimized protocol for retinal vein occlusion using rose bengal and a laser-guided retinal imaging microscope system with recommendations to maximize its reproducibility in genetically modified strains.

Mouse models of retinal vein occlusion (RVO) are often used in ophthalmology to study hypoxic-ischemic injury in the neural retina. In this report, a ...

Oxygen-Induced Retinopathy Model for Ischemic Retinal Diseases in Rodents

One of the commonly used models for ischemic retinopathies is the oxygen-induced retinopathy (OIR) model. Here we describe detailed protocols for the OIR model induction and its readouts in both mice and rats. Retinal neovascularization is induced in OIR by exposing rodent pups either to hyperoxia (mice) or alternating levels of hyperoxia and hypoxia (rats). The primary readouts of these models are the size of neovascular (NV) and avascular (AVA) areas in the retina. This preclinical in vivo model can be used to evaluate the efficacy of potential anti-angiogenic drugs or to address the role of specific genes in the retinal angiogenesis by using genetically manipulated animals. The model has some strain and vendor specific variation in the OIR induction which should be taken into consideration when designing the experiments.

Oxygen-induced retinopathy (OIR) can be used to model ischemic retinal diseases such as retinopathy of prematurity and proliferative diabetic retinopathy and to serve as a model for proof-of-concept studies in evaluating antiangiogenic drugs for neovascular diseases. OIR induces robust and reproducible neovascularization in the retina that can be quantified.

One of the commonly used models for ischemic retinopathies is the oxygen-induced retinopathy (OIR) model. Here we describe detailed protocols for the OIR ...

Quantification of Vascular Parameters in Whole Mount Retinas of Mice with Non-Proliferative and Proliferative Retinopathies

Retinopathies are a heterogeneous group of diseases that affect the neurosensory tissue of the eye. They are characterized by neurodegeneration, gliosis&#160;and a progressive change in vascular function and structure. Although the onset of the retinopathies is characterized by subtle disturbances in visual perception, the modifications in the vascular plexus are the first signs detected by clinicians. The absence or presence of neovascularization determines whether the retinopathy is classified as either non-proliferative (NPDR) or proliferative (PDR). In this sense, several animal models tried to mimic specific vascular features of each stage to determine the underlying mechanisms involved in endothelium alterations, neuronal death and other events taking place in the retina. In this article, we will provide a complete description of the procedures required for the measurement of retinal vascular parameters in adults and early birth mice at postnatal day (P)17. We will detail the protocols to carry out retinal vascular staining with Isolectin GSA-IB4 in whole mounts for later microscopic visualization. Key steps for image processing with Image J Fiji software are also provided, therefore, the readers will be able to measure vessel density, diameter and tortuosity, vascular branching, as well as avascular and neovascular areas. These tools are highly helpful to evaluate and quantify vascular alterations in both non-proliferative and proliferative retinopathies.

This article describes a well-established and reproducible lectin stain assay for the whole mount retinal preparations and the protocols required for the quantitative measurement of vascular parameters frequently altered in proliferative and non-proliferative retinopathies.

Retinopathies are a heterogeneous group of diseases that affect the neurosensory tissue of the eye. They are characterized by neurodegeneration, ...

In Vivo Vascular Injury Readouts in Mouse Retina to Promote Reproducibility

Advancements in ophthalmic imaging tools offer an unprecedented level of access to researchers working with animal models of neurovascular injury. To properly leverage this greater translatability, there is a need to devise reproducible methods of drawing quantitative data from these images. Optical coherence tomography (OCT) imaging can resolve retinal histology at micrometer resolution and reveal functional differences in vascular blood flow. Here, we delineate noninvasive vascular readouts that we use to characterize pathological damage post vascular insult in an optimized mouse model of retinal vein occlusion (RVO). These readouts include live imaging analysis of retinal morphology, disorganization of retinal inner layers (DRIL) measure of capillary ischemia, and fluorescein angiography measures of retinal edema and vascular density. These techniques correspond directly to those used to examine patients with retinal disease in the clinic. Standardizing these methods enables direct and reproducible comparison of animal models with clinical phenotypes of ophthalmic disease, increasing the translational power of vascular injury models.

In Vivo Vascular Injury Readouts in Mouse Retina to Promote Reproducibility

Here, we present three data analysis protocols for fluorescein angiography (FA) and optical coherence tomography (OCT) images in the study of Retinal Vein Occlusion (RVO).

Advancements in ophthalmic imaging tools offer an unprecedented level of access to researchers working with animal models of neurovascular injury. To ...

Image-Guided Optical Coherence Tomography to Assess Structural Changes in Rodent Retinas

Ocular diseases, such as age-related macular degeneration, glaucoma, retinitis pigmentosa, and uveitis, are always accompanied by retinal structural changes. These diseases affecting the fundus always exhibit typical abnormalities in certain cell types in the retina, including photoreceptor cells, retinal ganglion cells, cells in the retinal blood vessels, and cells in the choroidal vascular cells. Noninvasive, highly efficient, and adaptable imaging techniques are required for both clinical practice and basic research. Image-guided optical coherence tomography (OCT) satisfies these requirements because it combines fundus photography and high-resolution OCT, providing an accurate diagnosis of tiny lesions as well as important changes in the retinal architecture. This study details the procedures of data collection and data analysis for image-guided OCT and demonstrates its application in rodent models of choroidal neovascularization (CNV), optic nerve crush (ONC), light-induced retinal degeneration, and experimental autoimmune uveitis (EAU). This technique helps researchers in the eye field to identify rodent retinal structural changes conveniently, reliably, and tractably.

The protocol presented here details the procedures of data collection and data analysis for image-guided optical coherence tomography (OCT) and demonstrates its application in multiple rodent models of ocular diseases.

Ocular diseases, such as age-related macular degeneration, glaucoma, retinitis pigmentosa, and uveitis, are always accompanied by retinal structural ...

Monitoring Dynamic Growth of Retinal Vessels in Oxygen-Induced Retinopathy Mouse Model

Samenvatting

Meer video's verkennen