This project was supported by the Max Planck Society and received funding from the European Research Council (ERC) under the European Union&#39;s Horizon 2020 research and innovation program (grant agreement No. 637840 (QUANTPATTERN) and grant agreement No. 863952 (ACE-OF-SPACE)).

1. Assembling and using the transplantation device
<ol>
	<li>Assembling the transplantation device.
	<ol>
		<li>Connect the Luer tip 25 &#181;L gas-tight syringe and a micropipette holder with Luer lock fitting to assemble the transplantation device (Figure 1A). 
		NOTE: Wetting the Luer tip with a thin film of water can help to enhance the connection by holding the parts together via water adhesion and cohesion.</li>
		<li>Mount the device directly onto a manual micromanipulator (Figure 1B). The device can be controlled with the dominant hand alone, freeing up the other hand for additional tasks.</li>
	</ol>
	</li>
	<li>Preparing the transplantation needle.
	<ol>
		<li>Produce a transplantation needle by pulling a glass capillary pipette (without filament) with a micropipette puller.</li>
		<li>Break the tip of the needle as smoothly as possible, as sharp edges increase the chance of scratching the yolk while transplanting, which is fatal to the embryo. 
		NOTE: The tip can be easily broken with a straight-edge razor blade under a stereomicroscope. However, using a microforge allows to generate a precise opening of the desired size. For ectopic source generation, an outer diameter of approximately 50-60 &#181;m is appropriate. For extirpations and germline transplantation, the outer diameter of the needle should measure approximately 80-90 &#181;m to increase the number of transplanted cells.</li>
		<li>Insert the ready-to-use needle into the transplantation device (Figure 1A).</li>
	</ol>
	</li>
	<li>Using the transplantation device.
	<ol>
		<li>Place the micromanipulator with the transplantation device next to a stereomicroscope (Figure 1B).</li>
		<li>Remove the plunger and lower the transplantation needle into the transplantation dish filled with Ringer&#39;s solution (see step 2.2.1) at a 45&#176; angle until the tip of the needle is immersed (Figure 1B). Water will rush up the needle due to capillary action.</li>
		<li>Insert the plunger approximately halfway to flush out the Ringer&#39;s solutions, leaving only a small volume of water in the thin, tapered part of the needle (Figure 1C). 
		NOTE: This is the neutral position, and the water level should be stable there for a while (&#62;20 min). If the water level is unstable, the air is leaking; reconnect the Luer lock fitting or replace the syringe.</li>
		<li>When using a transplantation needle for the first time, coat its inside by drawing up yolk from a sacrificed embryo and then expelling the yolk material completely. The coating will help to reduce the adherence of cells to the glass during subsequent procedures.</li>
		<li>Gently position the donor embryo with the help of the needle and then position the needle opening orthogonal to the embryo&#39;s surface (Figure 1D). 
		NOTE: The position will be different for different assays. For ectopic signaling molecule source generation and cell extirpations, this will be the top of the animal pole (Figure 1E); for germline transplantation, this will be the margin (Figure 1D,F).</li>
		<li>Slowly and carefully pull up the plunger to draw the cells into the needle. 
		NOTE: If the cells are taken up too quickly, they can be damaged. If done correctly, the cells should come out as a cylindrical column. Avoid taking up yolk into the needle, as the transplanted yolk is toxic for the host embryo.</li>
		<li>Stop the suction by gently pushing the plunger down slightly once the desired number of cells is drawn in. Remove the needle from the embryo by jerking the needle to the side in a short and swift motion. Leave some Ringer&#39;s solution on either side of the cell column, and restrict the cells to the tapered end of the needle (Figure 1C,D). 
		NOTE: The liquid in front of the cell column will help to force apart the cells of the host embryos when depositing the cell column.</li>
		<li>Clear any remaining yolk or cell debris by slowly moving the plunger up and down - while the needle remains immersed - to wash the cells with Ringer&#39;s solution. If done correctly, the undamaged cells will remain adhered together in a column while the debris is washed away. 
		NOTE: Great care must be taken during this step as the water level will rise past the tapered end of the needle. This will cause a sudden influx of water, which can be used to wash the cells. However, once the water level has passed the tapered end, the fine control with the plunger will be reduced, and the plunger has to be moved more slowly and carefully.</li>
		<li>Move the transplantation dish with the non-dominant hand to position the needle orthogonal to the surface (either animal pole or margin) of the host embryo (Figure 1D-F).</li>
		<li>Gently apply slight pressure, and then give a swift, sharp movement to pierce the enveloping layer of the host embryo. Take care not to scratch the yolk with the needle. 
		NOTE: Applying slight pressure onto the embryo by carefully squeezing it against the walls of the well increases the embryo&#39;s surface tension and thus facilitates the piercing of the enveloping layer.</li>
		<li>Once the needle is inside, gently push the plunger to extrude the column of cells into the embryo while slowly retracting the needle at the same time (Figure 1D-F).</li>
	</ol>
	</li>
	<li>Cleaning the transplantation needle.
	<ol>
		<li>Rinse the needle by moving the plunger up and down while the needle is immersed in deionized water. 
		NOTE: If the needle remains dirty, rinse it with 10 M sodium hydroxide solution before rinsing it again with water.</li>
		<li>Store the needle in an appropriate box for further usage.</li>
	</ol>
	</li>
</ol>
2. Generating ectopic sources of secreted signaling molecules in zebrafish embryos
<ol>
	<li>Preparing the host and donor embryos.
	<ol>
		<li>Collect freshly laid embryos by mating zebrafish.</li>
		<li>Dechorionate 1-cell stage zebrafish embryos by incubating up to 100 embryos in 0.5 mg/mL of pronase solution for approximately 15 min in a small glass Petri dish (a detailed description of this procedure has been published by Rogers, K. W. et al.14). 
		NOTE: Alternatively, the embryos may also be dechorionated at the high stage just before transplantation (step 2.2), but this requires the injected donor embryos and uninjected host embryos to be dechorionated separately.</li>
		<li>Submerge the embryos in embryo medium in a 200 mL beaker. 
		NOTE: Dechorionated blastula and gastrula stage embryos are very delicate. Their exposed yolk will adhere to plastic surfaces and rupture upon contact with air. Hence, they must remain completely immersed in embryo medium, transferred with a glass pipet, and maintained in either agarose-coated (1% in embryo medium) plastic dishes or glass Petri dishes.</li>
		<li>Carefully empty out most of the embryo medium and slowly fill the beaker with fresh embryo medium. The mild agitation caused this way will facilitate the removal of the weakened chorions. Repeat this step 2-3 times.</li>
		<li>Transfer the dechorionated embryos using a glass Pasteur pipette into an agarose-coated injection dish. 
		NOTE: Flaming the tip of the glass Pasteur pipette by exposing it to a Bunsen burner flame can melt and smooth out the edge, helping to prevent damage to the embryos.</li>
		<li>Inject the mRNA encoding the fluorescently tagged protein into a subset of embryos (a detailed description of this procedure has been published by Rogers, K. W. et al.14). Inject the mRNA into the cell, not the yolk, for near-homogeneous expression. Injected embryos will serve as donors, while uninjected embryos will serve as hosts. 
		NOTE: The amount and type of injected mRNA will depend on the signaling molecule being studied and usually ranges from 20 to 200 pg2,4,5,6 (but can be as high as 1000 pg in certain cases4).</li>
		<li>Transfer the injected embryos to an agarose-coated six-well dish filled with embryo medium. Incubate at 28 &#176;C until the embryos reach the early sphere stage.</li>
	</ol>
	</li>
	<li>Transplanting cells to generate ectopic sources.
	<ol>
		<li>Fill a transplantation dish (with individual triangular wedge-shaped wells, see Table of Materials) with Ringer&#39;s solution (116 mM NaCl, 2.8 mM KCl, 1 mM CaCl2, 5 mM HEPES; store the HEPES buffer at 4 &#176;C). 
		NOTE: The calcium in Ringer&#39;s solution promotes cell adhesion and helps the embryo heal from the transplantation procedure.</li>
		<li>Transfer the embryos into the transplantation dish.</li>
		<li>Position the host and donor embryos in alternating columns, in each case with the animal pole oriented toward the transplantation needle.</li>
		<li>Carry out the transplantation as described in section 1.3. For ectopic source transplantation, take source cells from the top of the animal pole and deposit them into the same location in the host embryo (Figure 1E). 
		NOTE: Washing the cells with Ringer&#39;s solution as detailed in step 1.3.8 is important for ectopic source generation to make sure that already secreted signaling molecules are not carried over to the host. Do not transplant too many cells to ensure that the source is not dispersed. A column approximately 80 &#181;m in diameter and 100 &#181;m in length is appropriate for many applications.</li>
		<li>Allow the host embryo to stay in Ringer&#39;s solution for 30 min to 1 h to recover.</li>
		<li>Examine whether cells were successfully transplanted using a fluorescence stereomicroscope (Figure 2).</li>
		<li>After recovery, transfer the embryos to an agarose-coated six-well plate filled with embryo medium and incubate them at 28 &#176;C.</li>
	</ol>
	</li>
</ol>
3. Generating size-reduced embryos by cell extirpation
<ol>
	<li>Preparing embryos for extirpation.
	<ol>
		<li>Collect freshly laid embryos from zebrafish of the desired genotype.</li>
		<li>Incubate the embryos at 28 &#176;C until they reach the high stage.</li>
		<li>Dechorionate the embryos as described in steps 2.1.2-2.1.5 when the embryos reach the high stage. 
		NOTE: In this example, cell extirpation is performed at the sphere stage. Accordingly, embryos are dechorionated approximately 30 min to 1 h earlier.</li>
	</ol>
	</li>
	<li>Optional: Labeling the yolk syncytial layer (YSL). 
	NOTE: If desired, inject fluorescent dextrans into the YSL before extirpating cells. This technique allows to determine whether the YSL remains intact after cell removal, which is important for normal embryogenesis15. Alternatively, in vitro synthesized mRNAs or proteins can also be injected into the YSL.
	<ol>
		<li>Use a Pasteur pipette to transfer the dechorionated embryos to an agarose-coated injection dish filled with embryo water.</li>
		<li>Orient the embryos laterally, with the blastoderm margin pointing toward the injection needle (Figure 3A).</li>
		<li>Inject 0.5 nL of 1.5 &#181;g/&#181;L 10 kDa Alexa568-Dextran into the YSL, aiming for a region between the blastoderm cells and the yolk at a depth of about one-third of the embryo&#39;s diameter. Inject all embryos within one row. 
		NOTE: Since the injection needle does not need to pierce through the chorion, a small (~4 &#181;m) and sharp opening is advantageous.</li>
		<li>Rotate the embryos by 180&#176; so that the opposite side of the blastoderm margin is pointing toward the injection needle (Figure 3A).</li>
		<li>Inject another 0.5 nL of 1.5 &#181;g/&#181;L 10 kDa Alexa568-Dextran into the YSL as described in step 3.2.3, yielding a total injection volume of 1 nL per embryo. 
		NOTE: Injecting from two sides allows for a more even distribution of fluorescent dextran within the YSL.</li>
		<li>Examine the result of the injection under a fluorescence stereomicroscope. If done correctly, the fluorescent signal will be restricted to the YSL (Figure 3B) and not be visible in the intercellular space of the blastoderm.</li>
	</ol>
	</li>
	<li>Extirpating cells
	<ol>
		<li>Fill a transplantation dish with Ringer&#39;s solution (see step 2.2.1).</li>
		<li>Transfer the embryos to the transplantation dish.</li>
		<li>Orient the embryos with the animal pole toward the transplantation needle (Figure 3C).</li>
		<li>Carefully remove cells from the animal pole region as described in steps 1.3.5-1.3.7, thereby reducing the blastoderm to the desired size.</li>
		<li>Discard the removed cells by expelling them from the transplantation needle.</li>
		<li>Once the procedure is completed, allow the embryos to stay in Ringer&#39;s solution for 30 min to 1 h to recover.</li>
		<li>OPTIONAL: Examine the integrity of the YSL under a fluorescence stereomicroscope (Figure 3D).</li>
		<li>Transfer the embryos to an agarose-coated plate filled with embryo medium and incubate them at 28 &#176;C.</li>
	</ol>
	</li>
</ol>
4. Creating maternal-zygotic mutants by germline transplantation
<ol>
	<li>Preparing host and donor embryos.
	<ol>
		<li>Collect freshly laid embryos from both mutant and wild-type zebrafish. Embryos from zebrafish with a mutant background will serve as donors, while embryos from zebrafish with a wild-type background will serve as hosts. 
		NOTE: Germline transplantation requires a high number of starting embryos (~50 for donors, ~500 for hosts) to ensure a good number of successful germline transplants that survive into adulthood.</li>
		<li>Transfer the embryos to an agarose-coated injection dish with embryo medium using a Pasteur pipette. 
		NOTE: Injections are done before dechorionation to increase throughput. Needles for injection through the chorion need to be blunt and have a larger opening (~10 &#181;m) to prevent clogging.</li>
		<li>Inject the donor embryos with 1 nL of 100 ng/&#181;L mRNA encoding GFP with a nos1 3&#39;UTR. Inject the mRNA into the yolk to increase the throughput. 
		NOTE: The nos1 3&#39;UTR will stabilize the mRNA in the primordial germ cells, causing the germ cells to be strongly fluorescent when imaged 1 day post-fertilization10.</li>
		<li>Inject the host embryos with 1 nL of 0.33 mM (3 &#181;g/&#181;L) dead end (dnd) morpholino. Inject the morpholino into the yolk to increase the throughput. 
		NOTE: The dnd morpholino blocks primordial germ cell formation, which ensures that the host embryo&#39;s germline will be exclusively populated with cells from the donor after transplantation10.</li>
		<li>Transfer the injected embryos to plastic Petri dishes with embryo medium. Incubate at 28 &#176;C until the embryos reach the high stage.</li>
		<li>Dechorionate the embryos as described in steps 2.1.2-2.1.5 when the embryos reach the high stage.</li>
	</ol>
	</li>
	<li>Transplantation of germ cells
	<ol>
		<li>Fill a transplantation dish with Ringer&#39;s solution (see step 2.2.1).</li>
		<li>Transfer the dechorionated sphere- to dome-stage embryos into the transplantation dish.</li>
		<li>Position the host embryos and donor embryos in alternating columns to transplant the cells from one donor embryo to six different host embryos. This increases the chance that germ cells from a given host embryo will successfully be transplanted.</li>
		<li>Orient the embryos with the margin toward the transplantation needle and carry out the transplantation as described in section 1.3. For germline transplantations (Figure 1D,F), take the source cells from the margin (where the primordial germ cells are located) and deposit them into the same location in the host embryo. 
		NOTE: Transplanting a large column (approximately 80 &#181;m in diameter and 600 &#181;m in length) will increase the chance of obtaining a successful germline transplant.</li>
		<li>Allow the embryo to stay in Ringer&#39;s solution for 30 min to 1 h to recover once the transplantation is completed. 
		NOTE: If not all&#160;donor embryos are expected to be homozygous mutants - e.g., if they result from a heterozygous incross - they need to be genotyped after transplantation to determine the genotype of the host&#39;s transplanted future germline. In this case, ensure that the positions of the host and donor embryos are not mixed up during handling.</li>
		<li>Use a fluorescence stereomicroscope to examine whether the cells were successfully transplanted (Figure 4A,B).</li>
		<li>Transfer the embryos into a 24-well agarose-coated plate. Group all the host embryos that received cells from the same donor into the same well and label them accordingly. Incubate them until the next day at 28 &#176;C.</li>
		<li>If required, transfer the donor embryos into labeled PCR strips for genotyping.</li>
	</ol>
	</li>
	<li>Screening for successful germline transplants
	<ol>
		<li>Screen the host embryos for successful germline transplants under a fluorescence stereomicroscope approximately 30 h post-fertilization (hpf). The germ cells are found at the groove above the yolk extension (Figure 4C). 
		NOTE: Typical experiments with the device and strategy presented here will have a success rate of ~60%-80% to obtain at least one host embryo carrying transplanted germ cells per donor embryo. A previous report described a ~10% efficiency10.</li>
		<li>If applicable, discard embryos that received cells from donor embryos with an incorrect genotype. Grow larvae with successfully transplanted germ cells to adulthood according to standard husbandry conditions and following institutional guidelines.</li>
	</ol>
	</li>
</ol>

<ol>
	<li>Spemann, H., Mangold, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Induction+of+embryonic+primordia+by+implantation+of+organizers+from+a+different+species.">Induction of embryonic primordia by implantation of organizers from a different species.</a> Archives for Microscopic Anatomy and Developmental Mechanics. 100 (3-4), 599-638 (1924).</li><li>M&#252;ller, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Differential+diffusivity+of+Nodal+and+Lefty+underlies+a+reaction-diffusion+patterning+system.">Differential diffusivity of Nodal and Lefty underlies a reaction-diffusion patterning system.</a> Science. 336 (6082), 721-724 (2012).</li><li>Donovan, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Paracrine+Activin-A+signaling+promotes+melanoma+growth+and+metastasis+through+immune+evasion.">Paracrine Activin-A signaling promotes melanoma growth and metastasis through immune evasion.</a> Journal of Investigative Dermatology. 137 (12), 2578-2587 (2017).</li><li>Pomreinke, A. P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dynamics+of+BMP+signaling+and+distribution+during+zebrafish+dorsal-ventral+patterning.">Dynamics of BMP signaling and distribution during zebrafish dorsal-ventral patterning.</a> eLife. 6, 25861 (2017).</li><li>Almuedo-Castillo, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Scale-invariant+patterning+by+size-dependent+inhibition+of+Nodal+signaling.">Scale-invariant patterning by size-dependent inhibition of Nodal signaling.</a> Nature Cell Biology. 20, 1032-1042 (2018).</li><li>Soh, G. H., Pomreinke, A. P., M&#252;ller, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Integration+of+Nodal+and+BMP+signaling+by+mutual+signaling+effector+antagonism.">Integration of Nodal and BMP signaling by mutual signaling effector antagonism.</a> Cell Reports. 31 (1), 107487 (2020).</li><li>Mahalwar, P., Walderich, B., Singh, A. P., N&#252;sslein-Volhard, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Local+reorganization+of+xanthophores+fine-tunes+and+colors+the+striped+pattern+of+zebrafish.">Local reorganization of xanthophores fine-tunes and colors the striped pattern of zebrafish.</a> Science. 345 (6202), 1362-1364 (2014).</li><li>Frohnh&#246;fer, H. G., Krauss, J., Maischein, H. M., N&#252;sslein-Volhard, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Iridophores+and+their+interactions+with+other+chromatophores+are+required+for+stripe+formation+in+zebrafish.">Iridophores and their interactions with other chromatophores are required for stripe formation in zebrafish.</a> Development. 140 (14), 2997-3007 (2013).</li><li>Chen, Y., Schier, A. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+zebrafish+Nodal+signal+Squint+functions+as+a+morphogen.">The zebrafish Nodal signal Squint functions as a morphogen.</a> Nature. 411 (6837), 607-610 (2001).</li><li>Ciruna, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Production+of+maternal-zygotic+mutant+zebrafish+by+germline+replacement.">Production of maternal-zygotic mutant zebrafish by germline replacement.</a> Proceedings of the National Academy of Sciences of the United States of America. 99 (23), 14919-14924 (2002).</li><li>Westerfield, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> The zebrafish book. A guide for the laboratory use of zebrafish (Danio rerio). 4th edn. , (2000).</li><li>Kemp, H. A., Carmany-Rampey, A., Moens, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Generating+chimeric+zebrafish+embryos+by+transplantation.">Generating chimeric zebrafish embryos by transplantation.</a> Journal of Visualized Experiments:JoVE. (29), e1394 (2009).</li><li>Capek, D., M&#252;ller, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Positional+information+and+tissue+scaling+during+development+and+regeneration.">Positional information and tissue scaling during development and regeneration.</a> Development. 146 (24), 177709 (2019).</li><li>Rogers, K. W., Bl&#228;&#223;le, A., Schier, A. F., M&#252;ller, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measuring+protein+stability+in+living+zebrafish+embryos+using+fluorescence+decay+after+photoconversion+(FDAP).">Measuring protein stability in living zebrafish embryos using fluorescence decay after photoconversion (FDAP).</a> Journal of Visualized Experiments: JoVE. (95), e52266 (2015).</li><li>Carvalho, L., Heisenberg, C. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+yolk+syncytial+layer+in+early+zebrafish+development.">The yolk syncytial layer in early zebrafish development.</a> Trends in Cell Biology. 20 (10), 586-592 (2010).</li><li>Porazinski, S. R., Wang, H., Furutani-Seiki, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dechorionation+of+medaka+embryos+and+cell+transplantation+for+the+generation+of+chimeras.">Dechorionation of medaka embryos and cell transplantation for the generation of chimeras.</a> Journal of Visualized Experiments: JoVE. (46), e2055 (2010).</li><li>Centanin, L., Hoeckendorf, B., Wittbrodt, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fate+restriction+and+multipotency+in+retinal+stem+cells.">Fate restriction and multipotency in retinal stem cells.</a> Cell Stem Cell. 9 (6), 553-562 (2011).</li></ol>

The authors have no conflicts of interest to declare.

The success of a transplantation experiment strongly relies on the fine motor skills of the experimenter. To successfully carry out the procedures, practice is required. However, the instrument presented here is relatively easy to learn and use compared to others on the market, and, in general, only a few days of practice are needed.
The success of the transplantation procedure can be enhanced by taking several precautions. One step is to ensure that the micromanipulator is of good quality and capable of smooth operation. Adding an ocular with higher magnification to the stereomicroscope can help to precisely position the needle relative to the embryo. Using well-breeding zebrafish or medaka to acquire healthy embryos and taking care not to damage the embryos during handling (especially during and after the dechorionation step) will also enhance the success rate.
Problems with delayed toxicity can be more difficult to troubleshoot. If an embryo dies after a few hours - but not immediately following transplantation - the yolk might have been damaged by the needle (e.g., by entering the embryo too deeply), or perhaps the cells were ejected too forcefully. Delayed toxicity and embryonic death can also result from yolk or cell debris injected along with the donor cells; another cause can be deteriorating HEPES buffer in the Ringer&#39;s solution. These problems can be overcome by washing the cells (see step 1.3.8) or by simply using a fresh batch of buffer, respectively. Furthermore, deformed host embryos in germline transplantation experiments might result from excessively high morpholino concentrations. It is crucial to use enough morpholino to fully ablate the host&#39;s wild-type germline, thereby preventing these cells from contributing to the offspring - but at the same time, excessively high morpholino concentrations need to be avoided. Consistent morpholino amounts across all injected host embryos (a few hundred in a typical experiment) are therefore key to the success of germline transplantations. This can be helped by supplementing the morpholino injection mix with an easily visible tracer dye14, which can be tracked under a fluorescence stereomicroscope to ensure that all embryos receive the same injection volume.
The procedures described in this protocol exclusively involve manipulations of cells in blastula-stage zebrafish or medaka embryos, but in the future, it will likely be possible to adapt the device to different stages and species by changing the diameter and shape of the transplantation needle.

From the classical experiments of Mangold and Spemann that demonstrated the existence of an organizer instructing the formation of an embryonic axis1, transplantation of cells between embryos has become an established technique for studying embryonic development2,3,4,5,6,7,8,9,10. A commonly used setup for transplantation consists of a micrometer drive-controlled gas-tight syringe connected to a micropipette holder through flexible tubing and a reservoir filled with mineral oil12,13. In this setup, the plunger of the syringe is moved through a screw. The pressure generated in this manner is transferred to the micropipette and used to draw cells out from one embryo and deposit them into another. However, this hydraulically operated device consists of many parts and is laborious to assemble from scratch. Similar devices can also be purchased as a complete working set, usually sold as Manual Microinjectors, and these commercial versions typically cost more than 1500 US$. In both the home-made and the commercial version, the micropipette for embryo manipulation is separated from the pressure-generating device (the gas-tight syringe) through oil-filled tubing. The manipulation of the micropipette and the movement of the plunger, therefore, have to be operated separately with different hands, reducing the throughput and utility. Furthermore, the devices are cumbersome to prepare for transplantation since the tubing needs to be carefully filled with oil while avoiding the formation of bubbles. Here, we describe an alternative pneumatically operated device for cell removal and transplantation that is inexpensive, easy to assemble, and simple to use.
The device presented here comprises a 25 &#181;L gas-tight syringe fitted with a micropipette holder and costs less than 80 US$ altogether. The device is easily assembled by inserting the micropipette holder into the syringe via Luer lock fitting (Figure 1A). The device is then directly mounted onto a micromanipulator, allowing the user to control both its position and the suction with a single hand directly at the micromanipulator. This conveniently leaves the other hand free to stabilize and move the transplantation dish containing donor and host embryos. The device works by direct suction with air and does not need to be filled with mineral oil. Due to the attractive forces between the water and the walls of the glass needle, a large movement in the plunger of the syringe is translated into a smaller movement in the water level within the needle, as long as the water level is in the tapered end of the glass needle. This allows precise control over the number of aspirated cells and the location of their insertion.
To demonstrate the utility of this device, we present three applications in zebrafish (Danio rerio) embryos. First, we show how to generate localized sources of secreted signaling molecules, which can be used to study gradient formation2,4,6. Here, donor embryos are injected with mRNA encoding a fluorescently labeled signaling molecule. The fluorescence-labeled donor cells are then transplanted to wild-type host embryos where the formation of a signal gradient can be imaged and analyzed. Second, we describe how the device can be used to remove cells by extirpation in order to generate size-reduced embryos5,13. Finally, we show how to robustly produce maternal-zygotic mutants by transplanting cells carrying a primordial germ cell reporter into host embryos in which the germ line had been ablated6,10. In the future, the transplantation device described here can be easily adapted to other embryological manipulations requiring the removal or transplantation of cells.

<table><tbody><tr><td>1.0 mm glass capillary, ends cut without filament</td><td></td><td></td><td>To make the transplantation needle</td></tr><tr><td>1.0 mm glass capillary, ends cut with filament</td><td></td><td></td><td>To make injection needles</td></tr><tr><td>200 mL glass beaker</td><td></td><td></td><td>For embryo dechorionation</td></tr><tr><td>24-well plastic plate</td><td></td><td></td><td>To be coated with agarose in order to incubate embryos</td></tr><tr><td>5 cm diameter glass Petri dish</td><td></td><td></td><td>For embryo dechorionation</td></tr><tr><td>6-well plastic plate</td><td></td><td></td><td>To be coated with agarose in order to incubate embryos</td></tr><tr><td>Agarose</td><td></td><td></td><td>To coat plastic dishes</td></tr><tr><td>&lt;i&gt;dnd1&lt;/i&gt; morpholino</td><td>Gene Tools</td><td></td><td>Sequence: GCTGGGCATCCATGTCTCCGAC&lt;br/&gt; CAT</td></tr><tr><td>Embryo medium</td><td></td><td></td><td>250 mg/L Instant Ocean salt, 1 mg/L methylene blue in reverse osmosis water adjusted to pH 7 with NaHCO&lt;sub&gt;3&lt;/sub&gt;</td></tr><tr><td>Fluorescence stereomicroscope with GFP/RFP filters and light source</td><td></td><td></td><td>To assess YSL injections and germ-line transplantations</td></tr><tr><td>Glass micropipette puller</td><td>Sutter Instrument Company</td><td>P-1000</td><td>To make the transplantation needle</td></tr><tr><td>Glass pasteur pipette</td><td>Kimble Chase (via Fisher)</td><td>63A53WT</td><td>For pipetting embryos; the tips can be flamed to smoothen out the edge</td></tr><tr><td>Incubator at 28 &amp;deg;C</td><td></td><td></td><td>For incubating zebrafish embryos</td></tr><tr><td>Luer tip 25 &amp;mu;L Hamilton syringe, 1700 series</td><td>Hamilton</td><td>Ref: 80201</td><td>Part of the transplantation device</td></tr><tr><td>Manual micromanipulator with 3 axes of movement</td><td>Narishige</td><td>M-152</td><td>For controlling the transplantation device</td></tr><tr><td>Manual pipetting pump</td><td>Bio-Tek</td><td>Cat. # 641</td><td>For use with the glass pipettes to transfer embryos</td></tr><tr><td>Metal dissecting probe</td><td></td><td></td><td>For moving and rotating zebrafish embryos</td></tr><tr><td>Microforge</td><td>Narishige</td><td>MF2</td><td>To make the transplantation needle</td></tr><tr><td>Microinjection apparatus</td><td></td><td></td><td>For injection of mRNA and morpholino into embryos</td></tr><tr><td>Microinjection molds, triangular grooves</td><td>Adaptive Science Tools</td><td>TU-1</td><td>To prepare microinjection plates with agarose</td></tr><tr><td>Microinjection-molds, single wells</td><td>Adaptive Science Tools</td><td>PT-1</td><td>To prepare transplantation plates with agarose</td></tr><tr><td>Micropipette holder with Luer fitting for a 1.0 mm glass capillary</td><td>World Precision Instruments</td><td>MPH6S10</td><td>Part of the transplantation device</td></tr><tr><td>mMessage mMachine Sp6&lt;br/&gt; transcription kit</td><td>Life Technologies</td><td>AM1340M</td><td>To generate capped mRNA for injection into embryos</td></tr><tr><td>Plasmid with &lt;i&gt;GFP-nos1 3&#039;UTR&lt;/i&gt;</td><td></td><td></td><td>Plasmid that can be transcriped to produce mRNA encoding GFP with the 3&#039;UTR of &lt;em&gt;nos1&lt;/em&gt;</td></tr><tr><td>Plastic petri dish 100 mm</td><td></td><td></td><td>To be coated with agarose in order to make injection and transplantation dishes</td></tr><tr><td>Protease from &lt;em&gt;Streptomyces griseus&lt;/em&gt;</td><td>Sigma</td><td>P5147</td><td>For embryo dechorionation: Make a 5 mg/ml stock and use at 1 mg/ml to dechorionate embryos</td></tr><tr><td>Ringer&amp;rsquo;s solution</td><td></td><td></td><td>For 1 L: Add 6.78 g of NaCl, 0.22 g of KCl, 0.26 g of CaCl&lt;sub&gt;2&lt;/sub&gt; and 1.19 g of HEPES; then fill to 1 L; adjust pH to 7.2; sterilize by filtration</td></tr><tr><td>Stereomicroscope</td><td></td><td></td><td>For injection and transplantation</td></tr></tbody></table>

a simple and effective transplantation device for zebrafish embryos

Classical embryological manipulations, such as removing cells and transplanting cells within or between embryos, are powerful techniques to study complex developmental processes. Zebrafish embryos are ideally suited for these manipulations since they are easily accessible, relatively large in size, and transparent. However, previously developed devices for cell removal and transplantation are cumbersome to use or expensive to purchase. In contrast, the transplantation device presented here is economical, easy to assemble, and simple to use. In this protocol, we first introduce the handling of the transplantation device as well as its assembly from commercially and widely available parts. We then present three applications for its use: generation of ectopic clones to study signal dispersal from localized sources, extirpation of cells to produce size-reduced embryos, and germline transplantation to generate maternal-zygotic mutants. Finally, we show that the tool can also be used for embryological manipulations in other species such as the Japanese rice fish medaka.

Success and failure in the usage of the transplantation device for the three applications described above can readily be assessed by visual inspection under a stereomicroscope. In successful transplantations, the embryo should look normal and similar in shape and yolk clarity to untransplanted embryos, without large tears in the blastoderm. If the embryo is visibly damaged (Figure 4B), it will not develop normally. Ideally, transplanted cells expressing a fluorescent marker should appear as a continuous column when viewed under a fluorescence stereomicroscope (Figure 2A, Figure 4A). If the column is fragmented, this indicates that the cells were sheared by the suction into the transplantation needle or that the deposition of the cells was done too vigorously. This can be prevented by moving the plunger more slowly and gently.
Although the transplantation device has mainly been used on zebrafish embryos at blastula stages5,6, transplantation and cell extirpation work just as well for dechorionated blastula-stage embryos of the Japanese rice fish medaka (Oryzias latipes) (Figure 2B). Apart from embryo dechorionation, which has been described by Porazinski, S. R. et al.17, the same procedures as described above can be followed.
In the specific case of germline transplantation, a good transplant will result in an embryo with a long horizontal column of cells directly above the yolk margin (Figure 4A). However, whether germ cells were successfully transplanted can only be assessed on the following day (Figure 4C-F) due to background expression of GFP at blastula stages (Figure 1F). The primordial germ cells will appear as small fluorescent spheres in the groove directly above the yolk extension (Figure 4C-E). The presence of these cells at the correct location indicates successful germline transplantation. Cells with a different shape are not germ cells (e.g., elongated cells are typically muscle cells, Figure 4F). Also, if primordial germ cells are found outside the groove, this means that they have failed to migrate properly, and they will not be able to contribute to the embryo&#39;s germline. Finally, the general morphology of transplanted embryos should appear similar to untransplanted embryos (Figure 4D); the tail should not be deformed, and the head should not be shrunken or missing eyes (Figure 4E). These defects generally result from excessively high morpholino concentrations or from embryo damage during transplantation. Germline transplantation experiments as described here will typically result in 1-2 out of 6 host embryos with successfully transplanted germ cells for 60%-80% of donor embryos, depending on the experience of the experimenter. Thus, cells from 40-50 homozygous donor embryos need to be transplanted into 200-300 host embryos to raise approximately 30 individuals with mutant germ cells.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/62767/62767fig01.jpg" /> 
Figure 1: Assembly and usage of the transplantation device. (A) The transplantation device is assembled by connecting a gas-tight syringe with a micropipette holder through Luer lock fitting. The glass needle for transplantation is then inserted into the micropipette holder. (B) Photograph of the assembled transplantation device mounted onto a micromanipulator (please note that background and labels have been removed from the picture). (C) When using the transplantation device, it is important to ensure that the water level in the transplantation needle remains at the tapered end. (D) The device is used under a stereomicroscope to withdraw and insert cells from and into teleost embryos placed in individual wells of a transplantation dish. (E) For the generation of ectopic sources, cells are taken from the animal pole of a donor embryo (i-ii) and transferred into the animal pole of a host embryo (iii-vi). (F) For germline transplantation, a larger number of cells is taken from the margin of a donor embryo (i-ii), where the germ cells are located. The cells are then transferred into the margin of host embryos (iii-vi). <a href="https://www.jove.com/files/ftp_upload/62767/62767fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/62767/62767fig02.jpg" /> 
Figure 2: Generating clones by cell transplantation. (A) Example of a double clone generated by sequential transplantation of fluorescent cells (green) from a zebrafish donor into a zebrafish host embryo. Single and double clones can be used to study how secreted signaling molecules form spatiotemporal gradients2,4,5,6. (B) Example of a single clone generated by transplanting cells from a transgenic eGFP-expressing medaka donor (Wimbledon)17&#160;into a wild-type medaka host. Scale bars represent 100 &#181;m. <a href="https://www.jove.com/files/ftp_upload/62767/62767fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/62767/62767fig03.jpg" /> 
Figure 3: Generating size-reduced embryos by cell extirpation. (A) Before removing cells by extirpation, the YSL can be labeled by injecting fluorescent dyes into two opposing sides of the YSL. (B) Example of an embryo after YSL injection. (C) To generate size-reduced embryos, cells from the animal pole are removed by extirpation5. (D) Example of an embryo after cell extirpation. Note that the YSL stays intact. Scale bars represent 100 &#181;m. <a href="https://www.jove.com/files/ftp_upload/62767/62767fig03large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/62767/62767fig04.jpg" /> 
Figure 4: Germline transplantation. (A) Example of a successful transplantation of donor cells (green) into the host&#39;s marginal zone. (B) Example of an unsuccessful transplantation. The yolk of the host embryo was severely damaged, and the embryo will not be able to develop normally. (C) At 30 hpf, successfully transplanted germ cells will be found solely in the gonadal mesoderm at the anterior region of the yolk extension. (D) Example of a successful transplantation in which several GFP-labeled donor germ cells have populated the host&#39;s future gonad. (E) Example of an unsuccessful transplantation. Although germ cells have reached the gonadal mesoderm, the host embryo is severely deformed and will not develop normally. (F) Example of an unsuccessful transplantation. Fluorescent germ cells that failed to migrate into the correct location will not repopulate the gonads. Scale bars represent 100 &#181;m. Images in D-F were taken at a total magnification of approximately 50x. <a href="https://www.jove.com/files/ftp_upload/62767/62767fig04large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about A Simple and Effective Transplantation Device for Zebrafish Embryos at JoVE.com

A Simple and Effective Transplantation Device for Zebrafish Embryos

Embryological manipulations such as extirpation and transplantation of cells are important tools to study early development. This protocol describes a simple and effective transplantation device to perform these manipulations in zebrafish embryos.

Classical embryological manipulations, such as removing cells and transplanting cells within or between embryos, are powerful techniques to study complex ...

a-simple-and-effective-transplantation-device-for-zebrafish-embryos

Research

JoVE Journal

Developmental Biology

3.5K Views.  Friedrich Miescher Laboratory of the Max Planck Society. De techniek maakt het mogelijk om de functie en het bereik van signaalmoleculen tijdens embryogenese te bestuderen door ectopische signaalbronnen te transplanteren. Het vergemakkelijkt ook de efficiënte generatie van kiembaanmutanten. Het protocol kan worden toegepast op blastulastadium zebravissen en medaka embryo's, en waarschijnlijk ook op andere embryonale stadia en TDO-soorten.Om het transplantatieapparaat te monteren, sluit u een kunstaaspunt 25 microliter gasdichte spuit aan op...

Video: A Simple and Effective Transplantation Device for Zebrafish Embryos

Transplantation of Zebrafish Pediatric Brain Tumors into Immune-competent Hosts for Long-term Study of Tumor Cell Behavior and Drug Response

Tumor cell transplantation is an important technique to define the mechanisms controlling cancer cell growth, migration, and host response, as well as to assess potential patient response to therapy. Current methods largely depend on using syngeneic or immune-compromised animals to avoid rejection of the tumor graft. Such methods require the use of specific genetic strains that often prevent the analysis of immune-tumor cell interactions and/or are limited to specific genetic backgrounds. An alternative method in zebrafish takes advantage of an incompletely developed immune system in the embryonic brain before 3 days, where tumor cells are transplanted for use in short-term assays (i.e., 3 to 10 days). However, these methods cause host lethality, which prevents the long-term study of tumor cell behavior and drug response. This protocol describes a simple and efficient method for the long-term orthotopic transplantation of zebrafish brain tumor tissue into the fourth ventricle of a 2-day-old immune-competent zebrafish. This method allows: 1) long-term study of tumor cell behaviors, such as invasion and dissemination; 2) durable tumor response to drugs; and 3) re-transplantation of tumors for the study of tumor evolution and/or the impact of different host genetic backgrounds. In summary, this technique allows cancer researchers to assess engraftment, invasion, and growth at distant sites, as well as to perform chemical screens and cell competition assays over many months. This protocol can be extended to studies of other tumor types and can be used to elucidate mechanisms of chemoresistance and metastasis.

The transplantation of cancer cells is an important tool for the identification of cancer mechanisms and therapeutic responses. Current techniques depend on immune-incompetent animals. Here, we describe a method to transplant zebrafish tumor cells into immune-competent embryos for the long-term analysis of tumor cell behavior and in vivo drug responses.

Tumor cell transplantation is an important technique to define the mechanisms controlling cancer cell growth, migration, and host response, as well as to ...

Cancer Research

Microbead Implantation in the Zebrafish Embryo

The zebrafish has emerged as a valuable genetic model system for the study of developmental biology and disease. Zebrafish share a high degree of genomic conservation, as well as similarities in cellular, molecular, and physiological processes, with other vertebrates including humans. During early ontogeny, zebrafish embryos are optically transparent, allowing researchers to visualize the dynamics of organogenesis using a simple stereomicroscope. Microbead implantation is a method that enables tissue manipulation through the alteration of factors in local environments. This allows researchers to assay the effects of any number of signaling molecules of interest, such as secreted peptides, at specific spatial and temporal points within the developing embryo. Here, we detail a protocol for how to manipulate and implant beads during early zebrafish development.

The zebrafish is an excellent model system for genetic and developmental studies. Bead implantation is a valuable tissue manipulation technique that can be used to interrogate developmental mechanisms by introducing alterations in local cellular environments. This protocol describes how to perform microbead implantation in the zebrafish embryo.

The zebrafish has emerged as a valuable genetic model system for the study of developmental biology and disease. Zebrafish share a high degree of genomic ...

Analyzing In Vivo Cell Migration using Cell Transplantations and Time-lapse Imaging in Zebrafish Embryos

Cell migration is key to many physiological and pathological conditions, including cancer metastasis. The cellular and molecular bases of cell migration have been thoroughly analyzed in vitro. However, in vivo cell migration somehow differs from in vitro migration, and has proven more difficult to analyze, being less accessible to direct observation and manipulation. This protocol uses the migration of the prospective prechordal plate in the early zebrafish embryo as a model system to study the function of candidate genes in cell migration. Prechordal plate progenitors form a group of cells which, during gastrulation, undergoes a directed migration from the embryonic organizer to the animal pole of the embryo. The proposed protocol uses cell transplantation to create mosaic embryos. This offers the combined advantages of labeling isolated cells, which is key to good imaging, and of limiting gain/loss of function effects to the observed cells, hence ensuring cell-autonomous effects. We describe here how we assessed the function of the TORC2 component Sin1 in cell migration, but the protocol can be used to analyze the function of any candidate gene in controlling cell migration in vivo.

Analyzing In Vivo Cell Migration using Cell Transplantations and Time-lapse Imaging in Zebrafish Embryos

Combining cell transplantation, cytoskeletal labeling and loss/gain of function approaches, this protocol describes how the migrating zebrafish prospective prechordal plate can be used to analyze the function of a candidate gene in in vivo cell migration.

Cell migration is key to many physiological and pathological conditions, including cancer metastasis. The cellular and molecular bases of cell migration ...

Generating Chimeric Zebrafish Embryos by Transplantation

One of the most powerful tools used to gain insight into complex developmental processes is the analysis of chimeric embryos. A chimera is defined as an organism that contains cells from more than one animal; mosaics are one type of chimera in which cells from more than one genotype are mixed, usually wild-type and mutant. In the zebrafish, chimeras can be readily made by transplantation of cells from a donor embryo into a host embryo at the appropriate embryonic stage. Labeled donor cells are generated by injection of a lineage marker, such as a fluorescent dye, into the one-cell stage embryo. Labeled donor cells are removed from donor embryos and introduced into unlabeled host embryos using an oil-controlled glass pipette mounted on either a compound or dissecting microscope. Donor cells can in some cases be targeted to a specific region or tissue of the developing blastula or gastrula stage host embryo by choosing a transplantation site in the host embryo based on well-established fate maps.

A step-by-step guide to generating targeted chimeric zebrafish embryos by transplantation at the blastula or gastrula stage.

One of the most powerful tools used to gain insight into complex developmental processes is the analysis of chimeric embryos. A chimera is defined as an ...

Biology

Tissue Targeted Embryonic Chimeras: Zebrafish Gastrula Cell Transplantation

Certain fundamental questions in the field of developmental biology can only be answered when cells are placed in novel environments or when small groups of cells in a larger context are altered.  Watching how one cell interacts with and behaves in a unique environment is essential to characterizing cell functions.  Determining how the localized misexpression of a specific protein influences surrounding cells provides insightful information on the roles that protein plays in a variety of developmental processes.  Our lab uses the zebrafish model system to uniquely combine genetic approaches with classical transplantation techniques to generate genotypic or phenotypic chimeras.  We study neuron-glial cell interactions during the formation of forebrain commissures in zebrafish. This video describes a method that allows our lab to investigate the role of astroglial populations in the diencephalon and the roles of specific guidance cues that influence projecting axons as they cross the midline. Due to their transparency zebrafish embryos are ideal models for this type of ectopic cell placement or localized gene misexpression. Tracking transplanted cells can be accomplished using a vital dye or a transgenic fish line expressing a fluorescent protein. We demonstrate here how to prepare donor embryos with a vital dye tracer for transplantation, as well as how to extract and transplant cells from one gastrula staged embryo to another.  We present data showing ectopic GFP+ transgenic cells within the forebrain of zebrafish embryos and characterize the location of these cells with respect to forebrain commissures.  In addition, we show laser scanning confocal timelapse microscopy of Alexa 594 labeled cells transplanted into a GFP+ transgenic host embryo.  These data provide evidence that gastrula staged transplantation enables the targeted positioning of ectopic cells to address a variety of questions in Developmental Biology.

Zebrafish cell transplantation enables the combination of genetics and embryology to generate tissue specific chimeras. This video demonstrates gastrula staged cell transplantations that have allowed our lab to investigate the roles of astroglial populations and specific guidance cues during commissure formation in the forebrain.

Certain fundamental questions in the field of developmental biology can only be answered when cells are placed in novel environments or when small groups ...

Transplantation of GFP-expressing Blastomeres for Live Imaging of Retinal and Brain Development in Chimeric Zebrafish Embryos

Cells change extensively in their locations and property during embryogenesis. These changes are regulated by the interactions between the cells and their environment. Chimeric embryos, which are composed of cells of different genetic background, are great tools to study the cell-cell interactions mediated by genes of interest. The embryonic transparency of zebrafish at early developmental stages permits direct visualization of the morphogenesis of tissues and organs at the cellular level. Here, we demonstrate a protocol to generate chimeric retinas and brains in zebrafish embryos and to perform live imaging of the donor cells. The protocol covers the preparation of transplantation needles, the transplantation of GFP-expressing donor blastomeres to GFP-negative hosts, and the examination of donor cell behavior under live confocal microscopy. With slight modifications, this protocol can also be used to study the embryonic development of other tissues and organs in zebrafish. The advantages of using GFP to label donor cells are also discussed. 

We demonstrate a protocol to generate chimeric zebrafish embryos for live imaging cellular behavior during embryogenesis.

Cells change extensively in their locations and property during embryogenesis. These changes are regulated by the interactions between the cells and their ...

Utilizing Larval Zebrafish for Efficient In Vivo Tumor Studies

A Simple, Rapid, and Effective Method for Tumor Xenotransplantation Analysis in Transparent Zebrafish Embryos

In vivo studies of tumor behavior are a staple of cancer research; however, the use of mice presents significant challenges in cost and time. Here, we present larval zebrafish as a transplant model that has numerous advantages over murine models, including ease of handling, low expense, and short experimental duration. Moreover, the absence of an adaptive immune system during larval stages obviates the need to generate and use immunodeficient strains. While established protocols for xenotransplantation in zebrafish embryos exist, we present here an improved method involving embryo staging for faster transfer, survival analysis, and the use of flow cytometry to assess disease burden. Embryos are staged to facilitate rapid cell injection into the yolk of the larvae and cell marking to monitor the consistency of the injected cell bolus. After injection, embryo survival analysis is assessed up to 7 days post injection (dpi). Finally, disease burden is also assessed by marking transferred cells with a fluorescent protein and analysis by flow cytometry. Flow cytometry is enabled by a standardized method of preparing cell suspensions from zebrafish embryos, which could also be used in establishing the primary culture of zebrafish cells. In summary, the procedure described here allows a more rapid assessment of the behavior of tumor cells in vivo with larger numbers of animals per study arm and in a more cost-effective manner.

Author Spotlight: Advancing Cancer Therapeutics Using Tumor Xenotransplantation in Zebrafish

We describe a protocol for xenotransplantation into the yolk of transparent zebrafish embryos that is optimized by a simple, rapid staging method. Post-injection analyses include survival and assessing the disease burden of xenotransplanted cells by flow cytometry.

In vivo studies of tumor behavior are a staple of cancer research; however, the use of mice presents significant challenges in cost and time. Here, we ...

The Zebrafish Tol2 System: A Modular and Flexible Gateway-Based Transgenesis Approach

Fetal alcohol spectrum disorders (FASD) are characterized by a highly variable set of structural defects and cognitive impairments that arise due to prenatal ethanol exposure. Due to the complex pathology of FASD, animal models have proven critical to our current understanding of ethanol-induced developmental defects. Zebrafish have proven to be a powerful model to examine ethanol-induced developmental defects due to the high degree of conservation of both genetics and development between zebrafish and humans. As a model system, zebrafish possess many attributes that make them ideal for developmental studies, including large numbers of externally fertilized embryos that are genetically tractable and translucent. This allows researchers to precisely control the timing and dosage of ethanol exposure in multiple genetic contexts. One important genetic tool available in zebrafish is transgenesis. However, generating transgenic constructs and establishing transgenic lines can be complex and difficult. To address this issue, zebrafish researchers have established the transposon-based Tol2 transgenesis system. This modular system uses a multisite Gateway cloning approach for the quick assembly of complete Tol2 transposon-based transgenic constructs. Here, we describe the flexible Tol2 system toolbox and a protocol for generating transgenic constructs ready for zebrafish transgenesis and their use in ethanol studies.

This work describes a protocol for the modular Tol2 transgenesis system, a gateway-based cloning method to create and inject transgenic constructs into zebrafish embryos.

Fetal alcohol spectrum disorders (FASD) are characterized by a highly variable set of structural defects and cognitive impairments that arise due to ...

Robust Zebrafish Cell Transplantation for Regeneration and Development Research

High-resolution Cell Transplantation in Embryonic and Larval Zebrafish

Development and regeneration occur by a process of genetically encoded spatiotemporally dynamic cellular interactions. The use of cell transplantation between animals to track cell fate and to induce mismatches in the genetic, spatial, or temporal properties of donor and host cells is a powerful means of examining the nature of these interactions. Organisms such as chick and amphibians have made crucial contributions to our understanding of development and regeneration, respectively, in large part because of their amenability to transplantation. The power of these models, however, has been limited by low genetic tractability. Likewise, the major genetic model organisms have lower amenability to transplantation. 
The zebrafish is a major genetic model for development and regeneration, and while cell transplantation is common in zebrafish, it is generally limited to the transfer of undifferentiated cells at the early blastula and gastrula stages of development. In this article, we present a simple and robust method that extends the zebrafish transplantation window to any embryonic or larval stage between at least 1 and 7 days post fertilization. The precision of this approach allows for the transplantation of as little as one cell with near-perfect spatial and temporal resolution in both donor and host animals. While we highlight here the transplantation of embryonic and larval neurons for the study of nerve development and regeneration, respectively, this approach is applicable to a wide range of progenitor and differentiated cell types and research questions.

Author Spotlight: Mapping Cellular Connectivity in the Zebrafish Nervous System During Development and Regeneration

Here we present a protocol to transplant cells with high spatial and temporal resolution in zebrafish embryos and larvae at any stage between at least 1 and 7 days post fertilization.

Development and regeneration occur by a process of genetically encoded spatiotemporally dynamic cellular interactions. The use of cell transplantation ...

Zebrafish Breeding and Embryo Handling

Zebrafish (Danio rerio) are an important model organism that is particularly valuable for research in developmental biology. Zebrafish are extremely fertile and can produce hundreds of progeny per week, so it is relatively easy to collect a large number of embryos for high sample numbers. Furthermore, zebrafish undergo rapid development and embryos are transparent, allowing for easy visualization of developmental processes.
This video covers the steps required for the collection of newly fertilized zebrafish embryos. A brief overview of zebrafish mating behavior is presented, followed by instructions for setting up crosses in specialized laboratory breeding tanks that allow for controlled mating. Also covered are the conditions required to initiate the release of eggs (known as spawning) the morning after tanks are set. Next, essential techniques for working with embryos are presented, including the inhibition of pigment development with the chemical PTU, and dechorionation:&#160;a procedure in which the shell-like membrane surrounding the embryo (the chorion) is removed. Finally, the video concludes with some practical applications of these techniques in developmental research.

Zebrafish (Danio rerio) are an important model organism that is particularly valuable for research in developmental biology. Zebrafish are extremely ...

A Simple and Effective Transplantation Device for Zebrafish Embryos

Samenvatting

Meer video's verkennen

Hoofdstukken in deze video