Functional Magnetic Resonance Spectroscopy at 7 T in the Rat Barrel Cortex During Whisker Activation

Podsumowanie

After checking by blood-oxygen-level-dependent functional magnetic resonance imaging (BOLD fMRI) that the corresponding somatosensory barrel field cortex area (called S1BF) is correctly activated, the main goal of this study is to quantify lactate content fluctuations in the activated rat brains by localized proton magnetic resonance spectroscopy (¹H-MRS) at 7 T.

Streszczenie

Nuclear magnetic resonance (NMR) spectroscopy offers the opportunity to measure cerebral metabolite contents in vivo and noninvasively. Thanks to technological developments over the last decade and the increase in magnetic field strength, it is now possible to obtain good resolution spectra in vivo in the rat brain. Neuroenergetics (i.e., the study of brain metabolism) and, especially, metabolic interactions between the different cell types have attracted more and more interest in recent years. Among these metabolic interactions, the existence of a lactate shuttle between neurons and astrocytes is still debated. It is, thus, of great interest to perform functional proton magnetic resonance spectroscopy (¹H-MRS) in a rat model of brain activation and monitor lactate. However, the methyl lactate peak overlaps lipid resonance peaks and is difficult to quantify. The protocol described below allows metabolic and lactate fluctuations to be monitored in an activated brain area. Cerebral activation is obtained by whisker stimulation and ¹H-MRS is performed in the corresponding activated barrel cortex, whose area is detected using blood-oxygen-level-dependent functional magnetic resonance imaging (BOLD fMRI). All steps are fully described: the choice of anesthetics, coils, and sequences, achieving efficient whisker stimulation directly in the magnet, and data processing.

Wprowadzenie

The brain possesses intrinsic mechanisms that allow the regulation of its major substrate (i.e., glucose), both for its contribution and its utilization, depending on variations in local cerebral activity. Although glucose is the main energy substrate for the brain, experiments performed in recent years have shown that lactate, which is produced by the astrocytes, could be an efficient energy substrate for the neurons. This raises the hypothesis of a lactate shuttle between astrocytes and neurons¹. Known as ANLS, for astrocyte-neuron lactate shuttle², the theory is still highly debated but has led to the proposal that glucose, rather than going directly into neurons, may enter the astrocytes, where it is metabolized into lactate, a metabolite that is, then, transferred to the neurons, which use it as efficient energy substrate. If such a shuttle exists in vivo, it would have several important consequences, both for the understanding of basic techniques in functional cerebral imaging (positron emission tomography [PET]) and for deciphering the metabolic alterations observed in brain pathologies.

To study brain metabolism and, particularly, metabolic interactions between neurons and astrocytes, four main techniques are available (not including micro-/nanosensors): autoradiography, PET, two-photon fluorescent confocal microscopy, and MRS. Autoradiography was one of the first methods proposed and provides images of the regional accumulation of radioactive ¹⁴C-2-deoxyglucose in brain slices, while PET yields in vivo images of the regional uptake of radioactive ¹⁸F-deoxyglucose. They both have the disadvantage of using irradiative molecules while producing low-spatial resolution images. Two-photon microscopy provides cellular resolution of fluorescent probes, but light scattering by tissue limits the imaging depth. These three techniques have been used previously to study neuroenergetics in rodents during whisker stimulation^3,4,5,6. In vivo MRS has the dual advantage of being noninvasive and nonradioactive, and any brain structure can be explored. Moreover, MRS can be performed during neuronal activation, a technique called functional MRS (fMRS), which has been developed very recently in rodents⁷. Therefore, a protocol to monitor brain metabolism during cerebral activity by ¹H-MRS in vivo and noninvasively is proposed. The procedure is described in adult healthy rats with brain activation obtained by an air-puff whisker stimulation performed directly in a 7 T magnetic resonance (MR) imager but may be adapted in genetically modified animals, as well as in any pathological condition.

Protokół

All animal procedures were conducted in accordance with the Animal Experimentation Guidelines of the European Communities Council Directive of November 24, 1986 (86/609/EEC). The protocol met the ethical guidelines of the French Ministry of Agriculture and Forests and was approved by the local ethics committees (Comité d'éthique pour L'expérimentation Animale Bordeaux n°50112090-A).

NOTE: During the MR measurements, an adequate level of anesthesia and physiological monitoring (body temperature, respiratory rate) are indispensable requirements.

1. Animals

1. Use male Wistar rats weighing between 350 and 450 g.
2. Keep them on a 12:12 h light:dark cycle and provide food and water ad libitum.

2. Anesthesia

1. Prepare the equipment needed for anesthesia (Figure 1A,B, see Table of Materials): a 5 mL syringe containing medetomidine in physiological saline solution (240 µg/kg/h, with a perfusion rate of 20 µL/min), a 0.5 mL syringe containing atipamezole (20 μL, in 0.5 mL of saline solution), and eye ointment.
   NOTE: Keep all equipment under the extractor hood, except the 5 mL syringe containing medetomidine, which is placed in the syringe pump near the magnet for anesthesia during MR acquisitions.
2. Place the rat in the induction chamber, start the anesthesia by delivering 4% isoflurane, and adjust the oxygen flow rate to 1.5 L/min.
3. Evaluate the depth of anesthesia by assessing the withdrawal of paw reflexes.
4. When the rat does not respond to stimulation, take it out of the anesthesia box, place it on the bench with its nose in the isoflurane mask, and maintain anesthesia by delivering 2.5% in oxygen at 1.5 L/min.
5. Gently massage the tail and place the tourniquet (Figure 1C).
   NOTE: The massage can be performed in warm water, with a temperature between 38 and 42 °C, to obtain better vasodilation of the veins.
6. Insert the peripheral intravenous catheter (22 G), previously heparinized, in the left or right tail vein. Note that a venous return is observed (a drop of blood is visible at the distal part of the needle) when the catheter is correctly inserted (Figure 1D).
7. Blow out any air bubbles present in the catheter dead space volume using the 2 mL syringe containing physiological saline solution and heparin.
8. Apply the eye ointment and prepare the syringe containing atipamezole (17 µg/mL) to awaken the rat at the end of the experiment.

3. Rat Placement in Magnet for Whisker Stimulation

1. Place a breathing sensor on the magnet bed and then transfer the rat from the bench to the magnet bed. Place it in the prone position with its nose in the isoflurane mask, with the breathing sensor located between the ribcage and the magnet bed.
   NOTE: All equipment that enters the MRI room should be MRI-safe.
2. Decrease the isoflurane (from 4% to 1.5%–2%) during rat placement and switch the anesthesia to medetomidine at the end of this procedure. Ensure that the right whiskers are free, having cut the right edge at the front of the rat MRI bed beforehand to allow movement of the whiskers.
3. Hold the rat in position with tape and monitor its breathing which must be between 60 and 80 breaths per minute.
4. Make a sail that traps all right whiskers in the paper tape (Figure 2). Align the flexible outlet pipe of the air-puff system along the rat MRI bed so that the part exiting the tube is perpendicular and at around 1.5 cm from the sail. Fix it with paper tape.

4. Whisker Stimulation

1. Connect the flexible inlet pipe from a compressed air source (1 bar) to a solenoid control valve input and the outlet pipe to the solenoid control valve output (Figure 3). Ensure that the solenoid control valve stays outside the magnet room.
2. Plug the pulsing device into the solenoid valve and into the magnet using the transistor-transistor logic (TTL)-port. Configure it so that the pulsing frequency = 8 Hz, the pulsing time = 20 s, and the resting time = 10 s.
   NOTE: These parameters, visualized on the small liquid crystal display (LCD) screen, are adjustable via the three dedicated analogical potentiometers. The electronic pulsing device, which controls the paradigm, must be composed of high-quality electronic components to avoid any drift in time parameters (for correct postprocessing).

5. BOLD fMRI Acquisition

1. Place the rat brain so that it is in an upright position and use the ear bars to maintain it. Place the volume array coil above the rat’s head (Figure 4A) and fix it using tape. Check that the sail is moving correctly (anteroposterior movement, no rotation, and no friction of sail) when the air-puff system is turned On; then, switch it Off.
2. Insert the bed and the coil in the center of the magnet. Check that the sail is still moving correctly once the bed is inside the magnet when the air-puff system is On; then, switch it Off. Switch completely from isoflurane to medetomidine (perfusion rate: 20 µL/min).
3. Check that the rat is well located using a localization sequence (TE = 2.5 ms; TR = 100 ms; average = 1; repetition = 1; slice = 1 mm; image size = 256 x 256; field of view (FOV) = 50 x 50 mm; scan time = 12 s 800 ms). Drag the Localizer sequence tab into the Instruction name and click on Continue.
4. Drag the T2_Star_FID_EPI sequence tab into the Instruction name, center the FOV on the middle of the brain, and click on the Adjustment platform tab to open the edited scan instruction. Record a B₀ map and proceed to a scan shim.
   NOTE: For a B₀ map, use the following parameters: first echo time = 1.65 ms; TR = 20 ms, average = 1; flip angle = 30°; echo spacing = 3.805 ms; slice = 58 mm; image size = 64 x 64 x 64; FOV = 58 x 58 x 58 mm; scan time = 1 m 24 s 920 ms. For scan shim, use the following parameters: voxel selective excitation = STEAM Gaussian pulse; TE = 5 ms; mixing time = 10 ms; acquisition duration = 204.8 ms; bandwidth = 10,000 Hz; dwell time = 50 μs).
5. Start the T2 Star_FID_EPI sequence (TE = 16.096 ms; TR = 500 ms; average = 1; repetition = 600; slice = 1 mm; four consecutive slices; image size = 128 x 128; FOV = 20 x 20 mm; bandwidth = 333,333.3 Hz; scan time = 5 min 00 s).
   NOTE: Due to the TTL port, an external trigger signal will start the air-puff system at the same time. The paradigm = [20 s activation + 10 s rest] x 10, for the total duration of the 600 scans, 500 ms per scan. The slices are centered on the middle of the barrel field area.
6. Acquire another localization sequence (same as the one described in step 5.3) to compare with the first one and check whether the rat has moved during the T2_Star_FID_EPI sequence.
7. Bring the bed to its initial position, remove the volume array coil, and connect the surface coil.

6. BOLD Processing

1. Open the T2 Star_FID_EPI file and read the T2 Star_FID_EPI image in Image Display. Open the start-up window of the functional controller, called FunController.
2. In this Processing tab, select the functional imaging window and define the stimulation protocol (duration and alternation of On/Off periods, corresponding to the paradigm used).
3. Select the protocol window (dataset with 600 frames) and insert the value of 40 in the On Period tab and 20 in the Off period tab. Click on the Invert Attribution tab and drag the Stimulation States slider to the left to select the value 1.
4. In the preprocessing window, click on the Median filter in plane for preprocessing and on the Median filter (2D, 3D) for postprocessing.
5. Click on the Execute tab and drag the cursors to adjust the overlay lookup table. Visualize the activated brain area (Figure 4B).

7. Proton MRS Acquisitions

1. To correctly position the surface coil, modify the position of the rat head. Rotate the head (approximately 30° clockwise) so that the surface coil (Figure 5A) can be placed just above the left barrel cortex while being horizontal and located at the magnet center when inside the magnet.
2. Place the surface coil, fix it on the rat brain using tape (Figure 5B), and check that the sail is moving correctly (anteroposterior movement, no rotation, and no friction of the sail) when the air-puff system is turned On; then, switch it Off at the main switch.
3. Check that the sail is moving correctly once the bed is inside the magnet when the air-puff system is On. Then, switch it Off.
4. Check the rat is positioned correctly using a localization sequence. Set parameters as follows: TE = 2.5 ms; TR = 100 ms; average = 1; repetition = 1; slice = 1 mm; image size = 256 x 256; FOV = 50 x 50 mm; scan time = 12 s 800 ms.
   1. Drag the Localizer sequence tab into the Instruction name window and click on the Continue tab to execute the scan program.
5. When the brain localization is correct, drag the T2_TurboRARE sequence tab in the Instruction name window and click on Continue to execute the scan program. These anatomical images, together with the previous BOLD fMRI acquisition, will allow the correct localization of the voxel in the S1BF for MRS.
   NOTE: The T2_TurboRARE parameters are 14 slices, 2 mm per slice, FOV = 2.5 x 2.5 cm, TE = 100 ms, TR = 5,000 ms, matrix = 128 x 128, sequence time = 2 min 40 s.
6. Drag the LASER sequence tab into the Instruction name window, place the voxel (2 mm high, 2.5 mm long, 3 mm deep) at the center of the S1BF area.
   1. Use a rat brain atlas and the BOLD fMRI enhancement to localize the zone on the T2 images (Figure 6). Click on the Adjustment platform tab to open the edited scan instruction. Click on the Wobble tab and change the impedance (electronic loading) of the receive coil slightly to tune it. Click on the Apply tab when the tuning is finished to close the instruction editor and apply the changes in the edited instruction.
7. Record a B₀ map and proceed to scan shim and, then, perform a local shim.
   NOTE: For the B₀ map, use the following parameters: first echo time = 1.65 ms; TR = 20 ms, average = 1; flip angle = 30°; echo spacing = 3.805 ms; slice = 58 mm; image size = 64 x 64 x 64; FOV = 58 x 58 x 58 mm; scan time = 1 m 24 s 920 ms. For the scan shim, use the following parameters: voxel selective excitation STEAM Gaussian pulse; TE = 5 ms; mixing time = 10 ms; acquisition duration = 204.8 ms; bandwidth = 10,000 Hz; dwell time = 50 μs. For the local shim, use the following parameters: water suppression, VAPOR acquisition duration = 1,363.15 ms; points = 4,096; bandwidth in Hz = 3,004.81 Hz; bandwidth in ppm = 10 ppm; dwell time = 166.40 μs; spectral resolution = 0.37 Hz/points. The LASER parameters are: echo time = 19.26 ms; TR = 2,500 ms; averages = 128 or 32; scan time = 5 min 20 s or 1 min 20 s; acquisition points = 4,096.
8. Perform ¹H-MRS.
   1. Start the ¹H-MRS acquisition first during a resting period (4 x 32 LASER scans + 128 LASER scans; 2,500 ms per scan).
   2. Acquire another localization sequence (same as the one described in step 5.3) to compare with the first one recorded and ensure that the rat has not moved during the LASER acquisition.
   3. Perform ¹H-MRS during whisker activation using the LASER sequence (4 x 32 LASER scans + 128 LASER scans; 2,500 ms per scan) with the air-puff system On (paradigm = 20 s of activation and 10 s of rest).
   4. Once again, perform a localization sequence to check whether the rat has moved.
      NOTE: The number of scans and resting/activated periods can be adapted and modified, but always ensure that the rat is not moving by regularly performing a localization sequence.
9. Bring the bed to its initial position, remove the surface coil, and move the rat back to the bench. Inject atipamezole into a skin fold made in the rat’s back to reverse the anesthesia and awaken it.

8. Proton MRS Processing

1. Open the LCModel software and click on the appropriate tab to select the right data type ( Free Induction Decay file) and choose the right file. Click on the OK tab when this is done.
2. Optimize the quantification control parameters step by step.
   1. In the Title section, manually enter a title and define an adequate ppm range (e.g., 0.2 to 4.0 ppm) by manually typing in the necessary value in the respective fields.
   2. In the Basis file section, select and download the required file to fit the macromolecule baseline correctly (it can be provided by the software provider).
   3. Define and load the input control parameters. Prepare the save process of all useful file types beforehand (TABLE = compact tables; PS = necessary PostScript output; CSV = format for spreadsheets; COORD = coordinates for plots). Click on the RunLCModel tab to start the LCModel quantification.
3. Define selected metabolites to generate statistics.
   NOTE: LCModel provides metabolite quantification and estimates errors by a value termed Cramér-Rao lower bound (CRLB). A value with a CRLB < 15 is considered as an optimal quantification. A CRLB > 25 indicates an unreliable value.

Wyniki

This protocol allows the quantification of metabolite fluctuations during cerebral activation, which is obtained by right whisker stimulation directly in the magnet.

In this study, the overall goal of BOLD fMRI was to check that the whisker stimulation was efficient, to visualize the activated S1BF area, and to correctly locate the voxel for ¹H-fMRS. The device built for whisker activation is efficient. Indeed, when r...

Dyskusje

The barrel cortex, also called S1BF for the somatosensory cortex or barrel field, is a region within the cortical layer IV that can be observed using cytochrome c oxidase staining⁹, and its organization is well known since it has been largely described^10,11. One vibrissa is connected to one barrel, in which around 19,000 neurons are organized in a column¹². The whisker-to-barrel cortex pathway has several advantages...

Materiały

Name	Company	Catalog Number	Comments
0.5 mL syringe with needle	Becton, Dickinson and Company, USA	2020-10	0.33 mm (29 G) x 12.7 mm
1H spectroscopy surface coil	Bruker, Ettlingen, Germany	T116344
7T Bruker Biospec system	Bruker, Ettlingen, Germany	70/20 USR
Arduino Uno based pulsing device	custom made
Atipamezole	Vétoquinol, S.A., France	V8335602	Antisedan, 4.28 mg
Breathing mask	custom made
Eye ointment	TVM laboratoire, France	40365	Ocry gel 10 g
Induction chamber	custom made		30x17x15 cm
Inlet flexible pipe	Gardena, Germany	1348-20	4.6-mm diameter, 3m long
Isoflurane pump, Model 100 series vaporizer, classic T3	Surgivet, Harvard Apparatus	WWV90TT	from OH 43017, U.S.A
Isoflurane, liquid for inhalation	Vertflurane, Virbac, France	QN01AB06	1000 mg/mL
KD Scientific syringe pump	KD sientific, Holliston, USA	Legato 110
LCModel software	LCModel Inc., Ontario, Canada	6.2
Medetomidine hydrochloride	Vétoquinol, S.A., France	QN05CM91	Domitor, 1 mg/mL
Micropore roll of adhesive plaster	3M micropore, Minnesota, United States	MI912
Micropore roll of adhesive plaster	3M micropore, Minnesota, United States	MI925
Monitoring system of physiologic parameter	SA Instruments, Inc, Stony Brook, NY, USA	Model 1025
NaCl	Fresenius Kabi, Germany	B05XA03	0.9 % 250 mL
Outlet flexible pipe	Gardena, Germany	1348-20	4.6-mm diameter, 4m long
Paravision software	Bruker, Ettlingen, Germany	6.0.1
Peripheral intravenous catheter	Terumo, Shibuya, Tokyo, Japon	SP500930S	22 G x 1", 0.85x25 mm, 35 mL/min
Rat head coil	Bruker, Ettlingen, Germany
Sodic heparin, injectable solution	Choai, Sanofi, Paris, France	B01AB01	5000 IU/mL
Solenoid control valves, plunger valve 2/2 way direct-acting	Burkert, Germany	3099939	Model type 6013
Terumo 2 ml syringe	Terumo, Shibuya, Tokyo, Japon	SY243	with 21 g x 5/8" needle
Terumo 5 mL syringe	Terumo, Shibuya, Tokyo, Japon	05SE1
Wistar RJ-Han rats	Janvier Laboratories, France