K.B. is supported by NIH grant GM54544.

Part 1: Equipment and Supplies
<ol>
<li>A good dissection microscope is required for embryo dissections; 40X magnification is suggested, with 25X eye-pieces to maximally increase magnification.</li>
<li>Fine forceps (number 5) are required for manual selection of embryos and devitellinization of embryos.</li>
<li>Equipment to make and modify fine glass needles is required. Pulled-glass needles are required for the dissection. We prefer solid glass for dissection (last longer), but standard thick-walled glass tubing (outer diameter 1-1.5 mm) works as well. Some people use fine tungsten needles, electrolyzed to the desired sharpness in a bath of 1M NaOH using a 10+ Amp autotransformer battery. Sharpened tungsten dissection needles have the benefit that they are relatively resilient and long-lasting. Hollow glass needles (formed similar to patch clamp electrodes) are attached to plastic tubing and used during dissection for suction and expulsion of saline, as well as the controlled delivery of glue. A variety of glass pullers are available for manufacturing glass needles. Computer-programmed pullers can be preset to pull a variety of shapes and sizes. The Brown-Flaming models (Sutter Instrument Co.) are widely favored. A compound microscope (20-40X objective) should be available to inspect and modify electrodes prior to use.</li>
<li>Two types of solutions are commonly used to bath the embryonic tissues during dissection: 1) &ldquo;standard&rdquo; (Jan and Jan, 1976a) or &ldquo;modified standard&rdquo; (Broadie, 2000) salines, based on solutions commonly used for recording in other invertebrate systems, and 2) &ldquo;haemolymph-like&rdquo; (HL) salines (Stewart et al 1994), a compromise between the standard saline and the ionic concentrations measured in the Drosophila haemolymph. It should be noted that none of these salines accurately mimic the chemical composition of haemolymph in vivo (Broadie, 2000). Standard saline contains (in mM): 135 NaCl, 5 KCl, 4 MgCl2, 1.8 CaCl2, 72 sucrose, 5 TES, pH 7.2. Experimenters may also want to consider commercially prepared insect saline (e.g. Schneider&rsquo;s Insect Media), which is unsuitable for electrophysiological recording but most likely to protect the health of exposed tissues.</li>
</ol>
Part 2: Embryo Staging and Dissection
<ol>
<li>For optimal egg collection, maintain young (&lt;7 days), healthy male and female flies (20-40) on fresh laying pots for 2-3 days. Laying pots commonly consist of 100 ml plastic beakers (Tri-Pour) perforated to provide adequate air circulation, covering a 60 mm agar plate. Agar plates contain apple or grape juice hardened with agar. Several recipes exist, but one example is as follows: 700 ml of water, 25-30 grams agar, 300 ml of juice concentrate (grape or apple), 0.5g methyl paraben (p-hydroxymethylbenzoate), and 30g sugar. Autoclave the water and agar, and separately boil the p-hydroxymethylbenzoate with the sugar and juice. Mix the agar and juice solutions and quickly pour into 60 mm plates, removing bubbles.</li>
<li>Prior to egg collection, flies are fed with yeast paste (7 grams baker&rsquo;s yeast in 9 ml of water stored at 4&deg;C) on fresh plates, changed at least twice a day for at least two days. By day 3, a good pot should produce 100-200 eggs per hour. Better egg laying is observed on a pot maintained on its side with the agar in the plate scratched. Many embryos will be laid in or next to the scratches.</li>
<li>To collect large numbers of embryos, gently transfer the embryos from the agar plate into a basket using a paintbrush. A basket can be made with a 15 or 50 ml centrifuge tube. Cut off the bottom leaving enough surface area to trap a screen (70 &micro;m mesh) between the lid and the top of the tube. Rinse the embryos with dH20 and put into a Petri dish of fresh 50% to 100% bleach to remove the outer chorion. Alternatively, eggs can be collected individually using fine forceps, and dechorionated by placing them manually into a drop of bleach. De-chorionation can take from 30 seconds to 2 minutes (fresh bleach is much faster), and should be monitored under the dissection microscope. Removal of the chorion exposes the shiny, transparent vitelline membrane. Dechorionated eggs should be briefly rinsed, or placed in saline, as bleach rapidly destroys devitellinized tissues.</li>
<li>It is critical to carefully stage embryos to the desired developmental age. The defined Drosophila embryonic stages (1-17; Campos-Ortega and Hartenstein, 1985) are not useful, as all functional neuromuscular development occurs in late stage 16 or stage 17. Thus, embryos are staged by developmental hours at 25&deg;C in a humidified incubator, in hours after fertilization or, more commonly, after egg laying (AEL). Under these conditions, embryogenesis lasts 21 +/- 1 hr at 25&deg;C.</li>
<li>Eggs from a timed egg-lay (1-2 hrs) that are appropriately aged are next viewed for morphological criteria. After extensive washing in dH2O, the dechorionated eggs are placed in a plastic culture dish (under dH2O) for viewing. Correct staging can be confirmed with morphological criteria using reflected light with a dissection microscope (Campos-Ortega and Hartenstein, 1985). Mature late-stage embryos (22-24h AEL) on the verge of hatching are generally recognized by segmentation of the cuticle and inflated trachea. Embryos can also be genotyped using GFP balancers and a fluorescence dissection microscope with appropriate filters.</li>
<li>For dissection, dechorionated and developmentally staged embryos are attached (dorsal side up) on a coverslip under a drop of saline (see step 1.5). Embryos are removed from the vitelline membrane by puncturing the membrane near the anterior or posterior end with a glass micropipette or tungsten needle, and then gently freeing the embryo from the membrane. In preparation for dissection, the embryo should be positioned on the coverslip with the dorsal surface up (Dorsal side up dissection will expose the ventral nervous system and neuromusculature for experiments. However, the embryo can obviously be positioned in other ways to facilitate access to other tissues. )</li>
<li>Early stage embryos (&lt;16 hrs AEL) attach directly to clean glass or glass coated with polylysine (poly-L-lysine hydrobromide; Broadie and Bate, 1993a, b). Older embryos (&gt;16 hrs AEL), following cuticle formation, must be glued, ideally to Sylgard-coated (Dow Corning) coverslips. A water-polymerizing cyanoacrylate surgical or veterinary glue is used (Broadie and Bate, 1993c, d). The glue is delivered through a small glass electrode pipette (10-20 micrometer inner diameter tip) attached to a rubber tube with the glue flow controlled by mouth pressure. Care must be taken during glue delivery, as the glue polymerizes quickly upon contacting the saline. Note also that gluing cannot be performed in saline with no or low divalent ion concentrations, as the glue requires divalent ions to polymerize. Small amounts of glue are first used to firmly attach the head and tail.</li>
<li>Once the ends of the embryo are glued to the coverslip, an incision is made along the dorsal midline with a glass electrode or sharpened tungsten needle. This is made easier by gently perforating the line of incision prior to making the final cut. The sides of the incision are then attached to the coverslip with more glue, to gently spread the embryo flat. The internal organs including the gut, fat bodies and, optionally, trachea are then removed by suction using a glass pipette attached to rubber tubing (Broadie and Bate 1993a-c). The embryo should now be attached flat to the coverslip, epidermis down with the ventral central nervous system, peripheral nerves, and somatic musculature exposed for experimentation.</li>
</ol>

Precise staging of embryos is critical due to the rapid maturation of functional properties over the time course of just several hours. Several issues complicate this staging. First, most researchers use timed egg lays to stage embryos, but the egg laying time can vary enormously from animal to animal in different conditions (Broadie et al. 1992). In particular, females on a limited diet tend to retain fertilized eggs for prolonged periods prior to laying. It is therefore critical to &ldquo;clear&rdquo; females by feedin...

<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en">	
		
		<div>
		<table border="1">
		<thead>
		<tr>
		<th>Material Name</th>
		<th>Type</th>
		<th>Company</th>
		<th>Catalogue Number</th>
		<th>Comment</th>
		</tr>
		</thead>
		<tbody>
		
<tr>
<td>Embryo Collection Cages</td>
<td>&nbsp;</td>
<td>Genesee Scientific (www.flystuff.com)</td>
<td>59-100 (for 60 mm dish; other sizes available)</td>
<td>Cages can also be home made using punctured tri-pour beakers, as shown in video</td>
</tr>
<tr>
<td>Sylgard 184</td>
<td>&nbsp;</td>
<td>Dow Corning</td>
<td>Available from various companies</td>
<td>Surgical glue adheres better to sylgard-coated coverslips</td>
</tr>
<tr>
<td>Fine glass tubing, outer diameter 1.0-1.5 mm</td>
<td>&nbsp;</td>
<td>various</td>
<td>&nbsp;</td>
<td>For pulling into fine glass needles for dissection and tubes for glue delivery</td>
</tr>
<tr>
<td>Plastic tubing, to attach to glass pipette for mouth suction and glue application</td>
<td>&nbsp;</td>
<td>Tygon</td>
<td>&nbsp;</td>
<td>Tubing inner diameter needs to match glass outer diameter.</td>
</tr>		</tbody>
		</table>
		</div>

harvesting and preparing drosophila embryos for electrophysiological recording and other procedures

Drosophila is a premier genetic model for the study of both embryonic development and functional neuroscience. Traditionally, these fields are quite isolated from each other, with largely independent histories and scientific communities. However, the interface between these usually disparate fields is the developmental programs underlying acquisition of functional electrical signaling properties and differentiation of functional chemical synapses during the final phases of neural circuit formation. This interface is a critically important area for investigation. In Drosophila, these phases of functional development occur during a period of &lt;8 hours (at 25&deg;C) during the last third of embryogenesis. This late developmental period was long considered intractable to investigation owing to the deposition of a tough, impermeable epidermal cuticle. A breakthrough advance was the application of water-polymerizing surgical glue that can be locally applied to the cuticle to enable controlled dissection of late-stage embryos. With a dorsal longitudinal incision, the embryo can be laid flat, exposing the ventral nerve cord and body wall musculature to experimental investigation. This system has been heavily used to isolate and characterize genetic mutants that impair embryonic synapse formation, and thus reveal the molecular mechanisms governing the specification and differentiation of synapse connections and functional synaptic signaling properties.

Watch this Scientific Journal Video about Harvesting and Preparing Drosophila Embryos for Electrophysiological Recording and Other Procedures at JoVE.com

Harvesting and Preparing Drosophila Embryos for Electrophysiological Recording and Other Procedures

This technique exposes the Drosophila embryonic neuromusculature for immunohistochemistry or electrophysiological recording. It is useful for studying early events in neuromuscular development or performing electrophysiology in mutants that cannot hatch.

Harvesting and Preparing Drosophila Embryos for Electrophysiological Recording and Other Procedures

Drosophila is a premier genetic model for the study of both embryonic development and functional neuroscience. Traditionally, these fields are quite ...

harvesting-preparing-drosophila-embryos-for-electrophysiological

Research

JoVE Journal

Biology

13.3K Views.  University of Illinois. This technique exposes the Drosophila embryonic neuromusculature for immunohistochemistry or electrophysiological recording. It is useful for studying early events in neuromuscular development or performing electrophysiology in mutants that cannot hatch.

Video: Harvesting and Preparing Drosophila Embryos for Electrophysiological Recording and Other Procedures

Preparation of Neuronal Cultures from Midgastrula Stage Drosophila Embryos

This video illustrates the procedure for making primary neuronal cultures from midgastrula stage Drosophila embryos. The methods for collecting embryos and their dechorionation using bleach are demonstrated. Using a glass pipet attached to a mouth suction tube, we illustrate the removal of all cells from single embryos. The method for dispersing cells from each embyro into a small (5 l) drop of medium on an uncoated glass coverslip is demonstrated. A view through the microscope at 1 hour after plating illustrates the preferred cell density. Most of the cells that survive when grown in defined medium are neuroblasts that divide one or more times in culture before extending neuritic processes by 12-24 hours. A view through the microscope illustrates the level of neurite outgrowth and branching expected in a healthy culture at 2 days in vitro. The cultures are grown in a simple bicarbonate based defined medium, in a 5% CO2 incubator at 22-24&deg;C. Neuritic processes continue to elaborate over the first week in culture and when they make contact with neurites from neighboring cells they often form functional synaptic connections. Neurons in these cultures express voltage-gated sodium, calcium, and potassium channels and are electrically excitable. This culture system is useful for studying molecular genetic and environmental factors that regulate neuronal differentiation, excitability, and synapse formation/function.

This video demonstrates the preparation of primary neuronal cultures from midgastrula stage Drosophila embryos. Views of live cultures show cells 1 hour after plating and differentiated neurons after 2 days of growth in a bicarbonate-based defined medium. The neurons are electrically excitable and form synaptic connections.

This video illustrates the procedure for making primary neuronal cultures from midgastrula stage Drosophila embryos. The methods for collecting embryos ...

Electrophysiological Methods for Recording Synaptic Potentials from the NMJ of Drosophila Larvae

In this video, we describe the electrophysiological methods for recording synaptic transmission at the neuromuscular junction (NMJ) of Drosophila larva. The larval neuromuscular system is a model synapse for the study of synaptic physiology and neurotransmission, and is a valuable research tool that has defined genetics and is accessible to experimental manipulation. Larvae can be dissected to expose the body wall musculature, central nervous system, and peripheral nerves. The muscles of Drosophila and their innervation pattern are well characterized and muscles are easy to access for intracellular recording. Individual muscles can be identified by their location and orientation within the 8 abdominal segments, each with 30 muscles arranged in a pattern that is repeated in segments A2 - A7. Dissected drosophila larvae are thin and individual muscles and bundles of motor neuron axons can be visualized by transillumination1. Transgenic constructs can be used to label target cells for visual identification or for manipulating gene products in specific tissues. In larvae, excitatory junction potentials (EJP&#8217;s) are generated in response to vesicular release of glutamate from the motoneurons at the synapse. In dissected larvae, the EJP can be recorded in the muscle with an intracellular electrode. Action potentials can be artificially evoked in motor neurons that have been cut posterior to the ventral ganglion, drawn into a glass pipette by gentle suction and stimulated with an electrode. These motor neurons have distinct firing thresholds when stimulated, and when they fire simultaneously, they generate a response in the muscle. Signals transmitted across the NMJ synapse can be recorded in the muscles that the motor neurons innervate. The EJP&#8217;s and minature excitatory junction potentials (mEJP&#8217;s) are seen as changes in membrane potential. Electrophysiological responses are recorded at room temperature in modified minimal hemolymph-like solution2 (HL3) that contains 5 mM Mg2+ and 1.5 mM Ca2+. Changes in the amplitude of evoked EJP&#8217;s can indicate differences in synaptic function and structure. Digitized recordings are analyzed for EJP amplitude, mEJP frequency and amplitude, and quantal content.

Here we describe electrophysiological methods for measuring synaptic transmission at the neuromuscular junction of Drosophila larva. Evoked release is initiated artificially by stimulating the motor neuron axons, and transmission through the NMJ can be measured by the postsynaptic response evoked in the muscle.

In this video, we describe the electrophysiological methods for recording synaptic transmission at the neuromuscular junction (NMJ) of Drosophila larva. ...

Electrophysiological Recording in the Drosophila Embryo

Drosophila is a premier genetic model for the study of both embryonic development and functional neuroscience. Traditionally, these fields are quite isolated from each other, with largely independent histories and scientific communities. However, the interface between these usually disparate fields is the developmental programs underlying acquisition of functional electrical signaling properties and differentiation of functional chemical synapses during the final phases of neural circuit formation. This interface is a critically important area for investigation. In Drosophila, these phases of functional development occur during a period of &lt;8 hours (at 25&deg;C) during the last third of embryogenesis. This late developmental period was long considered intractable to investigation owing to the deposition of a tough, impermeable epidermal cuticle. A breakthrough advance was the application of water-polymerizing surgical glue that can be locally applied to the cuticle to enable controlled dissection of late-stage embryos. With a dorsal longitudinal incision, the embryo can be laid flat, exposing the ventral nerve cord and body wall musculature to experimental investigation. Whole-cell patch-clamp techniques can then be employed to record from individually-identifiable neurons and somatic muscles. These recording configurations have been used to track the appearance and maturation of ionic currents and action potential propagation in both neurons and muscles. Genetic mutants affecting these electrical properties have been characterized to reveal the molecular composition of ion channels and associated signaling complexes, and to begin exploration of the molecular mechanisms of functional differentiation. A particular focus has been the assembly of synaptic connections, both in the central nervous system and periphery. The glutamatergic neuromuscular junction (NMJ) is most accessible to a combination of optical imaging and electrophysiological recording. A glass suction electrode is used to stimulate the peripheral nerve, with excitatory junction current (EJC) recordings made in the voltage-clamped muscle. This recording configuration has been used to chart the functional differentiation of the synapse, and track the appearance and maturation of presynaptic glutamate release properties. In addition, postsynaptic properties can be assayed independently via iontophoretic or pressure application of glutamate directly to the muscle surface, to measure the appearance and maturation of the glutamate receptor fields. Thus, both pre- and postsynaptic elements can be monitored separately or in combination during embryonic synaptogenesis. This system has been heavily used to isolate and characterize genetic mutants that impair embryonic synapse formation, and thus reveal the molecular mechanisms governing the specification and differentiation of synapse connections and functional synaptic signaling properties.

Electrophysiological Recording in the Drosophila Embryo

Electrophysiological recordings from Drosophila embryos allow analyses of developing muscle and neuron electrical properties, as well as characterization of functional synaptogenesis at the glutamatergic neuromuscular junction and central cholinergic and GABAergic synapses.

Preparation of embryos for Electron Microscopy of the Drosophila embryonic heart tube

The morphogenesis of the Drosophila embryonic heart tube has emerged as a valuable model system for studying cell migration, cell-cell adhesion and cell shape changes during embryonic development. One of the challenges faced in studying this structure is that the lumen of the heart tube, as well as the membrane features that are crucial to heart tube formation, are difficult to visualize in whole mount embryos, due to the small size of the heart tube and intra-lumenal space relative to the embryo. The use of transmission electron microscopy allows for higher magnification of these structures and gives the advantage of examining the embryos in cross section, which easily reveals the size and shape of the lumen. In this video, we detail the process for reliable fixation, embedding, and sectioning of late stage Drosophila embryos in order to visualize the heart tube lumen as well as important cellular structures including cell-cell junctions and the basement membrane.

Preparation of embryos for Electron Microscopy of the Drosophila embryonic heart tube

We describe a process for fixation, embedding, sectioning, and imaging of late stage Drosophila embryos for Trasmission Electron Microscopy of the embryonic heart tube. This technique allows for the visualization of the heart tube lumen as well as the basement membrane, which lines the lumen of the heart.

The morphogenesis of the Drosophila  embryonic heart tube has emerged as a valuable model system for studying cell migration, cell-cell adhesion and cell ...

In-vivo Centrifugation of Drosophila Embryos

A major strategy for purifying and isolating different types of intracellular organelles is to separate them from each other based on differences in buoyant density. However, when cells are disrupted prior to centrifugation, proteins and organelles in this non-native environment often inappropriately stick to each other. Here we describe a method to separate organelles by density in intact, living Drosophila embryos. Early embryos before cellularization are harvested from population cages, and their outer egg shells are removed by treatment with 50% bleach. Embryos are then transferred to a small agar plate and inserted, posterior end first, into small vertical holes in the agar. The plates containing embedded embryos are centrifuged for 30 min at 3000g. The agar supports the embryos and keeps them in a defined orientation. Afterwards, the embryos are dug out of the agar with a blunt needle. Centrifugation separates major organelles into distinct layers, a stratification easily visible by bright-field microscopy. A number of fluorescent markers are available to confirm successful stratification in living embryos. Proteins associated with certain organelles will be enriched in a particular layer, demonstrating colocalization. Individual layers can be recovered for biochemical analysis or transplantation into donor eggs. This technique is applicable for organelle separation in other large cells, including the eggs and oocytes of diverse species.

In-vivo Centrifugation of Drosophila Embryos

We describe a method to separate organelles by density in living Drosophila embryos. Embryos are embedded in agar and centrifuged. This technique yields reproducible separation of major organelles along the anterior-posterior embryo axis. This method facilitates colocalization experiments and yields organelle fractions for biochemical analysis and transplantation experiments.

A major strategy for purifying and isolating different types of intracellular organelles is to separate them from each other based on differences in ...

Upright Imaging of Drosophila Embryos

Several well-known morphogenetic gradients and cellular movements occur along the dorsal/ventral axis of the Drosophila embryo. However, the current techniques used to view such processes are somewhat limited. The following protocol describes a new technique for mounting fixed and labeled Drosophila embryos for coronal viewing with confocal imaging. This method consists of embedding embryos between two layers of glycerin jelly mounting media, and imaging jelly strips positioned upright. The first step for sandwiching the embryos is to make a thin bedding of glycerin jelly on a slide. Next, embryos are carefully aligned on this surface and covered with a second layer of jelly. After the second layer is solidified, strips of jelly are cut and flipped upright for imaging. Alternatives are described for visualizing the embryos depending upon the type of microscope stand to be used. Since all cells along the dorsal-ventral axis are imaged within a single confocal Z-plane, our method allows precise measurement and comparison of fluorescent signals without photobleaching or light scattering common to 3D reconstructions of longitudinally mounted embryos.

Upright Imaging of Drosophila Embryos

Here we present a mounting protocol for stained Drosophila embryos in an upright position that allows imaging of cross-sections using Confocal microscopy.

Several well-known morphogenetic gradients and cellular movements occur along the dorsal/ventral axis of the Drosophila embryo. However, the current ...

Primary Cell Cultures from Drosophila Gastrula Embryos

Here we describe a method for preparing and culturing primary cells dissociated from Drosophila gastrula embryos. In brief, a large amount of staged embryos from young and healthy flies are collected, sterilized, and then physically dissociated into a single cell suspension using a glass homogenizer. After being plated on culture plates or chamber slides at an appropriate density in culture medium, these cells can further differentiate into several morphologically-distinct cell types, which can be identified by their specific cell markers. Furthermore, we present conditions for treating these cells with double stranded (ds) RNAs to elicit gene knockdown. Efficient RNAi in Drosophila primary cells is accomplished by simply bathing the cells in dsRNA-containing culture medium. The ability to carry out effective RNAi perturbation, together with other molecular, biochemical, cell imaging analyses, will allow a variety of questions to be answered in Drosophila primary cells, especially those related to differentiated muscle and neuronal cells.

Primary Cell Cultures from Drosophila Gastrula Embryos

We provide a detailed protocol for preparing primary cells dissociated from Drosophila embryos. The ability to carry out the effective RNAi perturbation, together with other molecular, biochemical and cell imaging methods will allow a variety of questions to be addressed in Drosophila primary cells.

Here we describe a method for preparing and culturing primary cells dissociated from Drosophila gastrula embryos.   In brief, a large amount of staged ...

Optimized Transfection Strategy for Expression and Electrophysiological Recording of Recombinant Voltage-Gated Ion Channels in HEK-293T Cells

The in vitro expression and electrophysiological recording of recombinant voltage-gated ion channels in cultured human embryonic kidney cells (HEK-293T) is a ubiquitous research strategy. HEK-293T cells must be plated onto glass coverslips at low enough density so that they are not in contact with each other in order to allow for electrophysiological recording without confounding effects due to contact with adjacent cells. Transfected channels must also express with high efficiency at the plasma membrane for whole-cell patch clamp recording of detectable currents above noise levels. Heterologous ion channels often require long incubation periods at 28&deg;C after transfection in order to achieve adequate membrane expression, but there are increasing losses of cell-coverslip adhesion and membrane stability at this temperature. To circumvent this problem, we developed an optimized strategy to transfect and plate HEK-293T cells. This method requires that cells be transfected at a relatively high confluency, and incubated at 28&deg;C for varying incubation periods post-transfection to allow for adequate ion channel protein expression. Transfected cells are then plated onto glass coverslips and incubated at 37&deg;C for several hours, which allows for rigid cell attachment to the coverslips and membrane restabilization. Cells can be recorded shortly after plating, or can be transferred to 28&deg;C for further incubation. We find that the initial incubation at 28&deg;C, after transfection but before plating, is key for the efficient expression of heterologous ion channels that normally do not express well at the plasma membrane. Positively transfected, cultured cells are identified by co-expressed eGFP or eGFP expressed from a bicistronic vector (e.g. pIRES2-EGFP) containing the recombinant ion channel cDNA just upstream of an internal ribosome entry site and an eGFP coding sequence. Whole-cell patch clamp recording requires specialized equipment, plus the crafting of polished recording electrodes and L-shaped ground electrodes from borosilicate glass. Drug delivery to study the pharmacology of ion channels can be achieved by directly micropipetting drugs into the recording dish, or by using microperfusion or gravity flow systems that produce uninterrupted streams of drug solution over recorded cells.

Reliable method for highly efficient in vitro expression and subsequent electrophysiological recording of recombinant voltage-gated ion channels in cultured human embryonic kidney cells (HEK-293T).

The in vitro expression and electrophysiological recording of recombinant voltage-gated ion channels in cultured human embryonic kidney cells (HEK-293T) ...

Isolation and Purification of Kinesin from Drosophila Embryos

Motor proteins move cargos along microtubules, and transport them to specific sub-cellular locations. Because altered transport is suggested to underlie a variety of neurodegenerative diseases, understanding microtubule based motor transport and its regulation will likely ultimately lead to improved therapeutic approaches. Kinesin-1 is a eukaryotic motor protein which moves in an anterograde (plus-end) direction along microtubules (MTs), powered by ATP hydrolysis. Here we report a detailed purification protocol to isolate active full length kinesin from Drosophila embryos, thus allowing the combination of Drosophila genetics with single-molecule biophysical studies. Starting with approximately 50 laying cups, with approximately 1000 females per cup, we carried out overnight collections. This provided approximately 10 ml of packed embryos. The embryos were bleach dechorionated (yielding approximately 9 grams of embryos), and then homogenized. After disruption, the homogenate was clarified using a low speed spin followed by a high speed centrifugation. The clarified supernatant was treated with GTP and taxol to polymerize MTs. Kinesin was immobilized on polymerized MTs by adding the ATP analog, 5'-adenylyl imidodiphosphate at room temperature. After kinesin binding, microtubules were sedimented via high speed centrifugation through a sucrose cushion. The microtubule pellet was then re-suspended, and this process was repeated. Finally, ATP was added to release the kinesin from the MTs. High speed centrifugation then spun down the MTs, leaving the kinesin in the supernatant. This kinesin was subjected to a centrifugal filtration using a 100 KD cut off filter for further purification, aliquoted, snap frozen in liquid nitrogen, and stored at -80 &deg;C. SDS gel electrophoresis and western blotting was performed using the purified sample. The motor activity of purified samples before and after the final centrifugal filtration step was evaluated using an in vitro single molecule microtubule assay. The kinesin fractions before and after the centrifugal filtration showed processivity as previously reported in literature. Further experiments are underway to evaluate the interaction between kinesin and other transport related proteins.

Isolation and Purification of Kinesin from Drosophila Embryos

This is a protocol to isolate active full length Kinesin from Drosophila embryos for single-molecule biophysical studies. We show how to collect embryos, make the embryo lysate, and then polymerize microtubules (MTs). Kinesin is purified by immobilizing it on the MTs, spinning down the Kinesin-MT complexes, and then releasing the kinesin from the MTs via ATP addition.

Motor proteins move cargos along microtubules, and transport them to specific sub-cellular locations. Because altered transport is suggested to underlie a ...

Preparing Individual Drosophila Egg Chambers for Live Imaging

Live cell imaging is an important technique applied to a number of Drosophila tissues used as models to investigate topics such as axis specification, cell differentiation and organogenesis 1. Correct preparation of the experimental samples is a crucial, often neglected, step. The goal of preparation is to ensure physiological relevance and to establish optimal imaging conditions. To maintain tissue viability, it is critical to avoid dehydration, hypoxia, overheating or medium deterioration 2. 
 The Drosophila egg chamber is a well established system for examining questions relating, but not limited, to body patterning, mRNA localization and cytoskeletal organization 3,4. For early- and mid-stage egg chambers, mounting in halocarbon oil is good for survival in that it allows free diffusion of oxygen, prevents dehydration and hypoxia and has superb optical properties for microscopy. Imaging of fluorescent proteins is possible through the introduction of transgenes into the egg chamber or physical injection of labeled RNA, protein or antibodies 5-7. For example, addition of MS2 constructs to the genome of animals enables real time observation of mRNAs in the oocyte 8. These constructs allow for in vivo labeling of mRNA through utilization of the MS2 bacteriophage RNA stem loop interaction with its coat protein 9. 
 Here, we present a protocol for the extraction of ovaries as well as isolating individual ovarioles and egg chambers from the female Drosophila. For a detailed description of Drosophila oogenesis see Allan C. Spradling (1993, reprinted 2009) 10.

Preparing Individual Drosophila Egg Chambers for Live Imaging

The Drosophila egg chamber is an excellent model for studying the mechanisms of mRNA localization. In order to capture the dynamic events that underpin the processes of localization, rapid high resolution imaging of live tissue is required. Here, we present a protocol for dissection and imaging of live samples with minimal disruption.

Live cell imaging is an important technique applied to a number of Drosophila tissues used as models to investigate topics such as axis specification, ...