We thank Prostate Cancer UK (CDF-12-002 Fellowship), and the Engineering and Physical Sciences Research Council (EPSRC) (EP/M008657/1) for funding.

1. Equipment setup
<ol>
	<li>Assemble the syringe pumps and SHM as follows.
	<ol>
		<li>Connect the &#34;To Computer&#34; port of the secondary syringe pump (Pump 02, for aqueous solution) to the &#34;To Network&#34; port of the master syringe pump (Pump 01, for ethanol lipid solution) using Pump to Pump network cable (Figure 1, yellow).</li>
		<li>Connect the &#34;To Computer&#34; port of the master pump to the &#34;RS232 Serial&#34; port of the computer using PC to Pump ...

<ol>
	<li>Needham, D., Park, J., Wright, A. M., Tong, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Materials+characterization+of+the+low+temperature+sensitive+liposome+(LTSL):+effects+of+the+lipid+composition+(lysolipid+and+DSPE-PEG2000)+on+the+thermal+transition+and+release+of+doxorubicin.">Materials characterization of the low temperature sensitive liposome (LTSL): effects of the lipid composition (lysolipid and DSPE-PEG2000) on the thermal transition and release of doxorubicin.</a> Faraday Discussions. 161, 515-534 (2013).</li><li>Ickenstein, L. M., Arfvidsson, M. C., Needham, D., Mayer, L. D., Edwards, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Disc+formation+in+cholesterol-free+liposomes+during+phase+transition.">Disc formation in cholesterol-free liposomes during phase transition.</a> Biochimica et Biophysica Acta - Biomembranes. 1614 (2), 135-138 (2003).</li><li>Valencia, P. M., Farokhzad, O. C., Karnik, R., Langer, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+technologies+for+accelerating+the+clinical+translation+of+nanoparticles.">Microfluidic technologies for accelerating the clinical translation of nanoparticles.</a> Nature Nanotechnology. 7 (10), 623-629 (2012).</li><li>Chen, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Rapid+discovery+of+potent+siRNA-containing+lipid+nanoparticles+enabled+by+controlled+microfluidic+formulation.">Rapid discovery of potent siRNA-containing lipid nanoparticles enabled by controlled microfluidic formulation.</a> Journal of the American Chemical Society. 134 (16), 6948-6951 (2012).</li><li>Forbes, N., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Rapid+and+scale-independent+microfluidic+manufacture+of+liposomes+entrapping+protein+incorporating+in-line+purification+and+at-line+size+monitoring.">Rapid and scale-independent microfluidic manufacture of liposomes entrapping protein incorporating in-line purification and at-line size monitoring.</a> International Journal of Pharmaceutics. 556, 68-81 (2019).</li><li>Dittrich, P. S., Manz, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Lab-on-a-chip:+microfluidics+in+drug+discovery.">Lab-on-a-chip: microfluidics in drug discovery.</a> Nature Reviews Drug Discovery. 5 (3), 210-218 (2006).</li><li>Capretto, L., Carugo, D., Mazzitelli, S., Nastruzzi, C., Zhang, X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+and+lab-on-a-chip+preparation+routes+for+organic+nanoparticles+and+vesicular+systems+for+nanomedicine+applications.">Microfluidic and lab-on-a-chip preparation routes for organic nanoparticles and vesicular systems for nanomedicine applications.</a> Advanced Drug Delivery Reviews. 65 (11-12), 1496-1532 (2013).</li><li>Cheung, C. C. L., Al-Jamal, W. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sterically+stabilized+liposomes+production+using+staggered+herringbone+micromixer:+Effect+of+lipid+composition+and+PEG-lipid+content.">Sterically stabilized liposomes production using staggered herringbone micromixer: Effect of lipid composition and PEG-lipid content.</a> International Journal of Pharmaceutics. 566, 687-696 (2019).</li><li>Suh, Y. K., Kang, S. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Review+on+Mixing+in+Microfluidics.">Review on Mixing in Microfluidics.</a> Micromachines. 1 (3), 82-111 (2010).</li><li>Jahn, A., Vreeland, W. N., Gaitan, M., Locascio, L. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Controlled+Vesicle+Self-Assembly+in+Microfluidic+Channels+with+Hydrodynamic+Focusing.">Controlled Vesicle Self-Assembly in Microfluidic Channels with Hydrodynamic Focusing.</a> Journal of the American Chemical Society. 126 (9), 2674-2675 (2004).</li><li>Stroock, A. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Chaotic+Mixer+for+Microchannels.">Chaotic Mixer for Microchannels.</a> Science. 295 (5555), 647-651 (2002).</li><li>Belliveau, N. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+Synthesis+of+Highly+Potent+Limit-size+Lipid+Nanoparticles+for+In+Vivo+Delivery+of+siRNA.">Microfluidic Synthesis of Highly Potent Limit-size Lipid Nanoparticles for In Vivo Delivery of siRNA.</a> Molecular Therapy - Nucleic Acids. 1 (8), 37 (2012).</li><li>Patra, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Under+the+influence+of+alcohol:+The+effect+of+ethanol+and+methanol+on+lipid+bilayers.">Under the influence of alcohol: The effect of ethanol and methanol on lipid bilayers.</a> Biophysical Journal. 90 (4), 1121-1135 (2006).</li><li>Komatsu, H., Rowe, E. S., Rowe, E. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+Cholesterol+on+the+Ethanol-Induced+Interdigitated+Gel+Phase+in+Phosphatidylcholine:+Use+of+Fluorophore+Pyrene-Labeled+Phosphatidylcholine.">Effect of Cholesterol on the Ethanol-Induced Interdigitated Gel Phase in Phosphatidylcholine: Use of Fluorophore Pyrene-Labeled Phosphatidylcholine.</a> Biochemistry. 30 (9), 2463-2470 (1991).</li><li>Lu, J., Hao, Y., Chen, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+Cholesterol+on+the+in+Lysophosphatidylcholine+Formation+of+an+Interdigitated+Gel+Phase+and+Phosphatidylcholine+Binary.">Effect of Cholesterol on the in Lysophosphatidylcholine Formation of an Interdigitated Gel Phase and Phosphatidylcholine Binary.</a> Journal of Biochemistry. 129 (6), 891-898 (2001).</li><li>Vanegas, J. M., Contreras, M. F., Faller, R., Longo, M. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Role+of+unsaturated+lipid+and+ergosterol+in+ethanol+tolerance+of+model+yeast+biomembranes.">Role of unsaturated lipid and ergosterol in ethanol tolerance of model yeast biomembranes.</a> Biophysical Journal. 102 (3), 507-516 (2012).</li><li>Haran, G., Cohen, R., Bar, L. K., Barenholz, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transmembrane+ammonium+sulfate+gradients+in+liposomes+produce+efficient+and+stable+entrapment+of+amphipathic+weak+bases.">Transmembrane ammonium sulfate gradients in liposomes produce efficient and stable entrapment of amphipathic weak bases.</a> Biochimica et Biophysica Acta (BBA) - Biomembranes. 1151 (2), 201-215 (1993).</li><li>Sadeghi, N., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Influence+of+cholesterol+inclusion+on+the+doxorubicin+release+characteristics+of+lysolipid-based+thermosensitive+liposomes.">Influence of cholesterol inclusion on the doxorubicin release characteristics of lysolipid-based thermosensitive liposomes.</a> International Journal of Pharmaceutics. 548 (2), 778-782 (2018).</li><li>Lawaczeck, R., Kainosho, M., Chan, S. I. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+formation+and+annealing+of+structural+defects+in+lipid+bilayer+vesicles.">The formation and annealing of structural defects in lipid bilayer vesicles.</a> Biochimica et Biophysica Acta (BBA) - Biomembranes. 443 (3), 313-330 (1976).</li><li>Komatsu, H., Okada, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ethanol-induced+aggregation+and+fusion+of+small+phosphatidylcholine+liposome:+participation+of+interdigitated+membrane+formation+in+their+processes.">Ethanol-induced aggregation and fusion of small phosphatidylcholine liposome: participation of interdigitated membrane formation in their processes.</a> BBA - Biomembranes. 1235 (2), 270-280 (1995).</li><li>Marsh, D., Bartucci, R., Sportelli, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Lipid+membranes+with+grafted+polymers:+physicochemical+aspects.">Lipid membranes with grafted polymers: physicochemical aspects.</a> Biochimica et Biophysica Acta (BBA) - Biomembranes. 1615 (1-2), 33-59 (2003).</li><li>Hood, R. R., Vreeland, W. N., DeVoe, D. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+remote+loading+for+rapid+single-step+liposomal+drug+preparation.">Microfluidic remote loading for rapid single-step liposomal drug preparation.</a> Lab on a Chip. 14 (17), 3359-3367 (2014).</li><li>Dalwadi, G., Benson, H. A. E., Chen, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparison+of+diafiltration+and+tangential+flow+filtration+for+purification+of+nanoparticle+suspensions.">Comparison of diafiltration and tangential flow filtration for purification of nanoparticle suspensions.</a> Pharmaceutical Research. , (2005).</li><li>Roces, C., Kastner, E., Stone, P., Lowry, D., Perrie, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Rapid+Quantification+and+Validation+of+Lipid+Concentrations+within+Liposomes.">Rapid Quantification and Validation of Lipid Concentrations within Liposomes.</a> Pharmaceutics. 8 (3), 29 (2016).</li><li>Kim, S. -. H., Kim, J. W., Kim, D. -. H., Han, S. -. H., Weitz, D. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Enhanced-throughput+production+of+polymersomes+using+a+parallelized+capillary+microfluidic+device.">Enhanced-throughput production of polymersomes using a parallelized capillary microfluidic device.</a> Microfluidics and Nanofluidics. 14 (3-4), 509-514 (2013).</li></ol>

The presented protocol describes the preparation of low temperature-sensitive liposomes (LTSLs) using a staggered herringbone micromixer (SHM). The LTSL10 formulation enables temperature-triggered burst release of doxorubicin within 5 minutes at a clinically attainable hyperthermic temperature of 42 &#176;C. Indocyanine green (ICG) can also be co-loaded for photothermal heating triggered the release of DOX. The method relies on: (i) self-assembly of phospholipids into liposomes under a homogenized solvent environment pro...

LTSL formulation is a clinically relevant liposomal product that has been developed to deliver the chemotherapeutic drug doxorubicin (DOX) and allows efficient burst drug release at clinically attainable mild hyperthermia (T &#8776; 41 &#176;C)1. The LTSL formulation consists of 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC), the lysolipid 1-stearoyl-2-hydroxy-sn-glycero-3-phosphatidylcholine (MSPC; M stands for &#34;mono&#34;) and PEGylated lipid 1,2-distearoyl-sn-glycero-3-phosphoethanolamine-N-[methoxy(polyethylene glycol)-2000] (DSPE-PEG2000). Upon reaching the phase transition temperature (Tm &#8776; 41 &#176;C), the lysolipid and DSPE-PEG2000 together facilitate the formation of membrane pores, resulting in a burst release of the drug2. The preparation of LTSLs primarily uses a bulk top-down approach, namely lipid film hydration and extrusion. It remains challenging to reproducibly prepare large batches with identical properties and in sufficient quantities for clinical applications3.
Microfluidics is an emerging technique for preparing liposomes, offering tunable nanoparticle size, reproducibility, and scalability3. Once the manufacturing parameters are optimized, the throughput could be scaled-up by parallelization, with properties identical to those prepared at bench scale3,4,5. A major advantage of microfluidics over conventional bulk techniques is the ability to handle small liquid volumes with high controllability in space and time through miniaturization, allowing faster optimization, while operating in a continuous and automated manner6. Production of liposomes with microfluidic devices is achieved by a bottom-up nanoprecipitation approach, which is more time and energy efficient because homogenization processes such as extrusion and sonication are unnecessary7. Typically, an organic solution (e.g. ethanol) of lipids (and hydrophobic payload) is mixed with a miscible non-solvent (e.g. water and hydrophilic payload). As the organic solvent mixes with the non-solvent, the solubility for the lipids is reduced. The lipid concentration eventually reaches a critical concentration at which the precipitation process is triggered7. Nanoprecipitates of lipids eventually grow in size and close into a liposome. The main factors governing the size and homogeneity of the liposomes are the ratio between the non-solvent and solvent (i.e. aqueous-to-organic flow rate ratio; FRR) and the homogeneity of the solvent environment during the self-assembly of lipids into liposomes8.
Efficient fluid mixing in microfluidics is therefore essential to the preparation of homogeneous liposomes, and various designs of mixers have been employed in different applications9. Staggered herringbone micromixer (SHM) represents one of the new generations of passive mixers, which enables high throughput (in range of mL/min) with a low dilution factor. This is superior to traditional microfluidic hydrodynamic mixing devices8,10. The SHM has patterned herringbone grooves, which rapidly mix fluids by chaotic advection9,11. The short mixing timescale of SHM (&#60; 5 ms, less than the typical aggregation time scale of 10&#8211;100 ms) allows lipid self-assembly to occur in a homogenous solvent environment, producing nanoparticles with uniform size distribution3,12.
The preparation of LTSLs with microfluidics is, however, not as straightforward compared to conventional liposomal formulations due to the lack of cholesterol8, without which lipid bilayers are susceptible to ethanol-induced interdigitation13,14,15. Until now, the effect of residual ethanol presents during the microfluidic production of liposomes has not been well understood. The majority of the reported formulations are inherently resistant to interdigitation (containing cholesterol or unsaturated lipids)16, which unlike LTSLs are both saturated and cholesterol-free.
The protocol presented herein uses SHM to prepare LTSLs for temperature triggered-release drug delivery. In the presented method, we ensured the microfluidic-prepared LTSLs are nano-sized (100 nm) and uniform (dispersity &#60; 0.2) by dynamic light scattering (DLS). Furthermore, we encapsulated DOX using the transmembrane ammonium sulfate gradient method (also known as remote loading)17 as a validation of the integrity of the LTSL lipid bilayer. Remote loading of DOX requires the liposome to maintain a pH-gradient in order to achieve high encapsulation efficiency (EE), which is unlikely to happen without an intact lipid bilayer. In this presented method, distinctive from typical microfluidic liposome preparation protocols, an annealing step is required before the ethanol is removed to enable the remote loading capability; i.e. to restore the integrity of the lipid bilayer.
As mentioned previously, hydrophilic and hydrophobic payloads can also be introduced to the initial solutions for the simultaneous encapsulation of payloads during the formation of LTSLs. As a proof-of-concept, indocyanine green (ICG), an FDA-approved near-infrared fluorescent dye, which is also a promising photothermal agent, is introduced to the initial lipid mixture and successfully co-loaded into the LTSLs. An 808 nm laser is used to irradiate the DOX/ICG-loaded LTSLs and successfully induce photothermal heating-triggered burst release of DOX within 5 min.
All the instruments and materials are commercially available, ready-to-use, and without the need for customization. Since all the parameters for formulating LTSLs have been optimized, following this protocol, researchers with no prior knowledge of microfluidics could also prepare the LTSLs, which serves as the basis of a thermosensitive drug delivery system.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC)</td>
			<td>Lipoid</td>
			<td>PC 16:0/16:0 (DPPC)</td>
			<td></td>
		</tr>
		<tr>
			<td>1,2-distearoyl-sn-glycero-3-phosphoethanolamine-N-[methoxy(polyethylene glycol)-2000] (DSPE-PEG2000)</td>
			<td>Lipoid</td>
			<td>PE 18:0/18:0-PEG 2000 
			(MPEG 2000-DSPE)</td>
			<td></td>
		</tr>
		<tr>
			<td>1-stearoyl-2-hydroxy-sn-glycero-3-phosphocholine (MSPC)</td>
			<td>Avanti Polar Lipid</td>
			<td>855775P-500MG</td>
			<td>Distributed by Sigma-Adrich; also known as Lyso 16:0 PC 
			(Not to be confused with 14:0/18:0 PC, which is also termed MSPC)</td>
		</tr>
		<tr>
			<td>4-(2-hydroxyethyl)-1-piperazineethanesulfonic acid (HEPES)</td>
			<td>Sigma-Aldrich</td>
			<td>H3375-100G</td>
			<td></td>
		</tr>
		<tr>
			<td>Adapters, Female Luer Lock to 1/4&#34;-28UNF</td>
			<td>IDEX Health &#38; Science</td>
			<td>P-624</td>
			<td>Requires 2 units. For the inlets</td>
		</tr>
		<tr>
			<td>Adapters, Union Assembly, 1/4&#34;-28UNF</td>
			<td>IDEX Health &#38; Science</td>
			<td>P-630</td>
			<td>Requires 2 units. (One unit included 2 nuts and 2 ferrules)</td>
		</tr>
		<tr>
			<td>Ammonium Sulfate ((NH4)2SO4)</td>
			<td>Sigma-Aldrich</td>
			<td>31119-1KG-M</td>
			<td></td>
		</tr>
		<tr>
			<td>Bijou vial</td>
			<td>VWR</td>
			<td>216-0980</td>
			<td>7 mL, clear, polystyrene vial</td>
		</tr>
		<tr>
			<td>Centrifugal Filter Unit</td>
			<td>Sigma-Aldrich</td>
			<td>UFC801008</td>
			<td>10 kDa MWCO, Amicon Ultra-4 Centrifugal Filter Unit</td>
		</tr>
		<tr>
			<td>Centrifuge</td>
			<td>ThermoFisher Scientific</td>
			<td>Heraeus Megafuge 8R</td>
			<td>With HIGHConic III Fixed Angle Rotor</td>
		</tr>
		<tr>
			<td>Cuvette</td>
			<td>Fisher Scientific</td>
			<td>11602609</td>
			<td>Disposable polystyrene cuvette, low volume, for DLS measurement</td>
		</tr>
		<tr>
			<td>Dialysis Kit - Pur-A-Lyzer Maxi</td>
			<td>Sigma-Aldrich</td>
			<td>PURX12015-1KT</td>
			<td>12-14 kDa MWCO</td>
		</tr>
		<tr>
			<td>Dimethyl Sulfoxide (DMSO)</td>
			<td>Sigma-Aldrich</td>
			<td>34943-1L-M</td>
			<td></td>
		</tr>
		<tr>
			<td>DLS Instrument</td>
			<td>Malvern Panalytical</td>
			<td>Zetasizer Nano ZS90</td>
			<td></td>
		</tr>
		<tr>
			<td>Doxorubicin Hydrochloride (DOX)</td>
			<td>Apollo Scientific</td>
			<td>BID0120</td>
			<td></td>
		</tr>
		<tr>
			<td>DSC Instrument</td>
			<td>TA Instruments</td>
			<td>TA Q200 DSC</td>
			<td></td>
		</tr>
		<tr>
			<td>DSC Tzero Hermetic Lids</td>
			<td>TA Instruments</td>
			<td>901684.901</td>
			<td>For DSC measurement</td>
		</tr>
		<tr>
			<td>DSC Tzero Pans</td>
			<td>TA Instruments</td>
			<td>901683.901</td>
			<td>For DSC measurement</td>
		</tr>
		<tr>
			<td>DSC Tzero Sample Press Kit</td>
			<td>TA Instruments</td>
			<td>901600.901</td>
			<td>For DSC measurement</td>
		</tr>
		<tr>
			<td>Ethanol</td>
			<td>VWR</td>
			<td>20821.330</td>
			<td>Absolute, &#8805;99.8%</td>
		</tr>
		<tr>
			<td>FC-808 Fibre Coupled Laser System</td>
			<td>CNI Optoelectronics Tech</td>
			<td>FC-808-8W-181315</td>
			<td>FOC-01-B Fiber Collimator included.</td>
		</tr>
		<tr>
			<td>Ferrule, 1/4&#34;-28UNF to 1/16&#34; OD</td>
			<td>IDEX Health &#38; Science</td>
			<td>P-200</td>
			<td>For the outlet</td>
		</tr>
		<tr>
			<td>Fibre Optic Temperature Probe</td>
			<td>Osensa</td>
			<td>PRB-G40</td>
			<td></td>
		</tr>
		<tr>
			<td>Glass Staggered Herringbone Micromixer (SHM)</td>
			<td>Darwin Microfluidics</td>
			<td>Herringbone Mixer - Glass Chip</td>
			<td></td>
		</tr>
		<tr>
			<td>Heating Tape</td>
			<td>Omega</td>
			<td>DHT052020LD</td>
			<td>Can be replaced by other syringe heater such as &#34;HTC&#34; or &#34;SRT series&#34; for slower heating. Manual wiring to a 3-pin plug required for 240V models</td>
		</tr>
		<tr>
			<td>Indocyanine Green</td>
			<td>Adooq</td>
			<td>A10473-100</td>
			<td>Distributed by Bioquote Limited (U.K.)</td>
		</tr>
		<tr>
			<td>Luer-lock Syringe, 5 mL</td>
			<td>VWR</td>
			<td>613-2043</td>
			<td>Hanke Sass Wolf SOFT-JECT 3-piece syringes, O.D. 12.45 mm</td>
		</tr>
		<tr>
			<td>Microplate Reader</td>
			<td>BMG Labtech</td>
			<td>FLUOstar Omega</td>
			<td>Installed with 485 nm (exictation) and 590 nm (emission) filters</td>
		</tr>
		<tr>
			<td>Microplate, 96-well, Black, Flat-bottom</td>
			<td>ThermoFisher Scientific</td>
			<td>611F96BK</td>
			<td>For fluorescence measurement in microplate reader</td>
		</tr>
		<tr>
			<td>Microplate, 96-well, Clear, Flat-bottom</td>
			<td>Grenier</td>
			<td>655101</td>
			<td>For absorbance measurement microplate reader</td>
		</tr>
		<tr>
			<td>Nut, 1/4&#34;-28UNF to 1/16&#34; OD</td>
			<td>IDEX Health &#38; Science</td>
			<td>P-245</td>
			<td>For the outlet</td>
		</tr>
		<tr>
			<td>PC to Pump Network Cable for Aladdin, 7ft</td>
			<td>World Precision Instruments</td>
			<td>NE-PC7</td>
			<td>Optional: Syringe pumps can be operated manually</td>
		</tr>
		<tr>
			<td>Pump control software - SyringePumpPro Software License for 2</td>
			<td>World Precision Instruments</td>
			<td>SYRINGE-PUMP-PRO-02</td>
			<td>Optional: Syringe pumps can be operated manually</td>
		</tr>
		<tr>
			<td>Pump to Pump Network Cable for Aladdin, 7 ft</td>
			<td>World Precision Instruments</td>
			<td>NE-NET7</td>
			<td>Optional: Syringe pumps can be operated manually</td>
		</tr>
		<tr>
			<td>Size exclusion chromatography (SEC) column</td>
			<td>GE Life Science</td>
			<td>17085101</td>
			<td>Sephadex G-25 resin in PD-10 Desalting Columns</td>
		</tr>
		<tr>
			<td>Sodium chloride (NaCl)</td>
			<td>Sigma-Aldrich</td>
			<td>31434-1KG-M</td>
			<td></td>
		</tr>
		<tr>
			<td>Sodium hydroxide (NaOH)</td>
			<td>Sigma-Aldrich</td>
			<td>S5881-500G</td>
			<td></td>
		</tr>
		<tr>
			<td>Syringe Pumps &#38; Cable (DUAL-PUMP-NE-1000)</td>
			<td>World Precision Instruments</td>
			<td>ALADDIN2-220/AL1000-220</td>
			<td></td>
		</tr>
		<tr>
			<td>Thermostat Temperature Controller</td>
			<td>Inkbird</td>
			<td>ITC-308</td>
			<td>Can be replaced by other syringe heater kit/thermostat</td>
		</tr>
		<tr>
			<td>Triton X-100</td>
			<td>Sigma-Aldrich</td>
			<td>X100-100ML</td>
			<td></td>
		</tr>
		<tr>
			<td>Tubing, ETFE (1/16&#34; OD)</td>
			<td>IDEX Health &#38; Science</td>
			<td>1516</td>
			<td></td>
		</tr>
		<tr>
			<td>USB To RS-232 Converter</td>
			<td>World Precision Instruments</td>
			<td>CBL-USB-232</td>
			<td>Optional: For computer without RS-232 port</td>
		</tr>
		<tr>
			<td>Water Bath</td>
			<td>Grant Instruments Ltd.</td>
			<td>JB Nova 12</td>
			<td></td>
		</tr>
	</tbody>
</table>

microfluidic production of lysolipid-containing temperature-sensitive liposomes

The presented protocol enables a high-throughput continuous preparation of low temperature-sensitive liposomes (LTSLs), which are capable of loading chemotherapeutic drugs, such as doxorubicin (DOX). To achieve this, an ethanolic lipid mixture and ammonium sulfate solution are injected into a staggered herringbone micromixer (SHM) microfluidic device. The solutions are rapidly mixed by the SHM, providing a homogeneous solvent environment for liposomes self-assembly. Collected liposomes are first annealed, then dialyzed to remove residual ethanol. An ammonium sulfate pH-gradient is established through buffer exchange of the external solution by using size exclusion chromatography. DOX is then remotely loaded into the liposomes with high encapsulation efficiency (&#62; 80%). The liposomes obtained are homogenous in size with Z-average diameter of 100 nm. They are capable of temperature-triggered burst release of encapsulated DOX in the presence of mild hyperthermia (42 &#176;C). Indocyanine green (ICG) can also be co-loaded into the liposomes for near-infrared laser-triggered DOX release. The microfluidic approach ensures high-throughput, reproducible and scalable preparation of LTSLs.

The preparation of LTSLs by microfluidics requires the lipid composition of DPPC/MSPC/DSPE-PEG2000 (80/10/10, molar ratio; LTSL10). Figure 7A (left) shows the appearance of as-prepared LTSL10 from step 2.9, as a clear and non-viscous liquid. LTSL10 formulation is developed from the conventional formulation, LTSL4 (DPPC/MSPC/DSPE-PEG2000, 86/10/4, molar ratio) since LTSL4 forms a gel-like viscous sample, as indicated by t...

Watch this Scientific Journal Video about Microfluidic Production of Lysolipid-Containing Temperature-Sensitive Liposomes at JoVE.com

Microfluidic Production of Lysolipid-Containing Temperature-Sensitive Liposomes

The protocol presents the optimized parameters for preparing thermosensitive liposomes using the staggered herringbone micromixer microfluidics device. This also allows co-encapsulation of doxorubicin and indocyanine green into the liposomes and the photothermal-triggered release of doxorubicin for controlled/triggered drug release.

The presented protocol enables a high-throughput continuous preparation of low temperature-sensitive liposomes (LTSLs), which are capable of loading ...

Microfluidics is an emerging technique for preparing liposomes of a tunable nanoparticle size and with great reproducibility and scalability. This protocol enables the continuous high through output production of low temperature sensitive liposomes for co-loading with a chemotherapeutic drug such as doxorubicin and a fluorescent dye such as indocyanine green. Cell preparation primarily use a top down approach such as lipid film hydration and extrusion.It remains challenging to prepare large and reproducible batches for clinical applications. A major advantage of microfluidics is the ability to handle small liquid volume with high controllability in space and time while operating in a continuous and automated manner. Demonstrating the procedure with Calvin Cheung will be Guanglong Ma and Amalia Ruiz, the post-doctoral researchers from my laboratory.To assemble the syringe pumps, use the pump-to-pump network cable to connect the to computer port of the secondary syringe pump to the to network port of the master syringe pump. Use the PC to pump network cable to connect the to computer port of the master pump to the RS-232 serial port of the computer. To assemble the staggard herringbone micromixer microfluidic device, use a nut and ferrule to connect tubing to each of the inlets and outlets of the device.Then use a second nut and ferrule and a union assembly to convert the terminal of the tubing for both inlets to a female luer. To set up the pump control software, use the setup button of the syringe pump to assign the address of the master syringe pump and secondary syringe pump to Ad:01 and Ad:02 respectively, then open the pump control software on the computer. The two syringe pumps should be detected automatically followed by a beeping sound.Select HSW Norm-Ject 5cc diameter equals 12.45 to assign the diameter to 12.45 millimeters. Set the rate to 0.25 milliliters per minute for pump one and 0.75 milliliters per minute for pump two. Set the volume to any value above five milliliters and select the infusion mode for both pumps.Then click set to confirm the settings. To prepare an LTSL10 or LTSL10 ICG lipid mixture, use one five milliliter luer lock syringe to withdraw one milliliter of lipid mixture and another five milliliter luer lock syringe to withdraw at least three milliliters of ammonium sulfate solution. Slide the barrel flange of the syringe to the syringe retainer of the pump to install the loaded syringes onto the syringe pumps in the upright position and attach the plunger flange of the syringe to the pusher block of the pump and wrap the other end of the heating tape and the temperature probe with the thermostat around the syringe containing the lipid solution.Wrap the end of the heating tape to the syringe containing the aqueous solution, connect the syringe containing the lipid mixture to the ethanol inlet, and connect the syringe containing the ammonium sulfate solution to the aqueous inlet. Adjust the plunger position to remove any air bubbles from the syringes as necessary and plug and unplug the heating tape in 10 second intervals until the temperature of the syringes reaches about 51 degrees. When the thermostat shows an appropriate temperature, click run all in the pump control software to run the syringe pumps and check that the fluid flow is free of air bubbles and any leakage.Collect the liposome samples into a vial and pause or stop the infusion when either syringe is almost empty. Anneal the collected liposome solutions in a 60 degree Celsius water bath for 1-1/2 hours before transferring the solutions to dialysis tubes for dialysis against one liter of 240 millimolar ammonium sulfate for at least four hours at 37 degrees Celsius. Then store the purified liposomes at four degrees Celsius.For remote loading of the liposomes by transmembrane pH gradient, load 25 milliliters of HBS onto the top of a size exclusion chromatography column and allow all of the eluent to flow through the column. Load one milliliter of dialyzed liposomes to the column. When all of the lipid solution has passed through the column, add 1.5 milliliters of fresh HBS to the column.When all of the buffer has passed through the column, add three milliliters of fresh HBS to the column and collect the eluent. Next, add DOX solution at a 1:20 DOX:phospholipid molar ratio to one milliliter of buffer exchange liposome solution in a Biju vial and place the vial in a 37 degree Celsius water bath for 1-1/2 hours. After loading, purify the liposomes by size exclusion chromatography as just demonstrated.For laser heating induced trigger release of the liposome contents, set the water bath to 37 degrees Celsius. When the temperature has stabilized, add 200 microliters of DOX loaded liposomes to each well of a clear 96-well plate and place the plate in the water bath with the bottom submerged in the water. Then set the laser system current to 2.27 amps and place the laser system collimator five centimeters vertically above the surface of the 96-well plate.Switch on the laser and use a fiber optic temperature probe to monitor the temperature once a minute. At five and 10 minutes, aspirate 10 microliters of DOX loaded liposomes from each well of the clear 96-well plate and add 190 microliters of HBS to three individual wells of a black 96-well plate. To assess complete drug release, mix 10 microliters of the liposomes with 170 microliters of HBS and 20 microliters of 1%Triton X-100 detergent solution in three individual wells of the black 96-well plate.Then measure the DOX fluorescence intensity on a plate reader. Microfluidic production of LTSL4 results in a gel-like viscous solution illustrated by the large number of trapped air bubbles while the preparation of LTSL10 results in the formation of a clear non-viscous liquid. Dynamic light scattering measurement of LTSL10 prepared at 51 degrees Celsius demonstrates the expected Z-average diameter and dispersity indicating the success of the experiment.When LTSL10 is prepared at 20 degrees Celsius, however, larger and more dispersed liposomes are obtained resulting in a suboptimal product. LTSLs prepared by the conventional method of lipid film hydration with extrusion demonstrate a DOX encapsulation efficiency of 50-80%With annealing, LTSL10 prepared by microfluidics results in a significant increase in DOX encapsulation efficiency to a mean of 85%indicating the success of the remote loading of DOX and the presence of the transmembrane pH gradient. The DOX release profile of LTSL10 has been determined to be temperature sensitive.LTSL10 has a relatively broad phase transition with onset at 41.6 degrees Celsius that peaks at 42.6 degrees Celsius. The efficiency of the ICG loading is dependent on the initial ICG concentration and the size and dispersity of the samples. Further, LTSL10 ICG irradiation with a near infrared laser induces photothermal heating triggering the release of DOX.When attempting this procedure, it is important to ensure a stable fluid flow such that the mixing of fluid and therefore the formation of liposomes remain reproducible. Liposome annealing and dialysis are two important steps for ensuring a stable liposome formulation with high loading capacity. In vivo testing can also be carried out to assess LTSL10 bio-distribution, drug release, and anticancer activity.Our protocol can be used for the successful microfluidic production of cholesterol-free lysolipid-containing thermosensitive liposomes for drug delivery applications.

microfluidic-production-lysolipid-containing-temperature-sensitive

Research

JoVE Journal

Bioengineering

8.8K vistas.  Queen's University Belfast. Microfluidics es una técnica emergente para la preparación de liposomas de un tamaño de nanopartículas sintonizables y con gran reproducibilidad y escalabilidad. Este protocolo permite la producción continua alta a través de la producción de liposomas sensibles a baja temperatura para la co-carga con un fármaco quimioterapéutico como doxorubicina y un tinte fluorescente como el verde indocyanina. La preparación celular utiliza principalmente un enfoque de arriba hacia abajo, como la...