We would like to thank Laura Schippers for writing the first versions of the cell loading protocol and Marcus de Goffau and Guille Zampar for scoring mitochondrial morphologies.

1. Production and Preparation of a Silicon Wafer Mold
Microfluidic chips are created from a silicon wafer mold produced by soft lithography. These wafers can be reused many times to produce microfluidic chips. It is advisable that production of a respective wafer is performed by a group specialized in microfluidics6.
The wafer is made in a two-step photolithography process using two different layers of negative photoresist, SU-87. The bottom layer is used to generate the cell trapping area (SU-8 2002; height 3-4 &mu;m), whereas the channels are made with the top layer (SU-8 2010; height 10 &mu;m). An impression of the wafer production process can be found in Huang et al8. The drawings of the microfluidic chips can be obtained from the authors as well as advice on how to obtain a respective wafer.
<ol>
	<li>Once the wafer is obtained, cut one piece of Tough-Tag into thin strips of about 0.5 mm by 3 mm with a scalpel and place them carefully on the wafer slightly on top of the channel structure between the inlet channels and the micropad array (Figure 2A). This will result in the formation of a large additional channel in each chip, which will not only be used during cell loading, but is also important for the stable operation of the microfluidic device.</li>
	<li>Cover the glass Petri dish with a double layer of aluminum foil and put the wafer in the Petri dish. The aluminum foil will prevent PDMS from running in between the wafer and the Petri dish. If PDMS does creep in between the wafer and the glass Petri dish, the wafer will become permanently fixed in the Petri dish. Although the wafer is still useable, it will not be possible to replace the glass Petri dish if it breaks and the PDMS will need to be cut out afterwards.</li>
</ol>
2. Production of Microfluidic Chips
<ol>
	<li>Place an empty plastic cup on the balance and tare the balance. Pour 40 g PDMS base into the plastic cup (for a 12 cm diameter glass Petri dish). Add PDMS curing agent with a disposable pipette in a w/w ratio of 1:10, i.e. about 4 ml.</li>
	<li>Mix the PDMS and curing agent thoroughly for several minutes. This can be done with the disposable plastic pipette that was used to pipette the curing agent. It is important that the mixture is well mixed prior to pouring it on top of the wafer. Poor mixing will cause part of the PDMS not to polymerize.</li>
	<li>Pour the PDMS on top of the wafer in the glass Petri dish.</li>
	<li>Mixing of PDMS with the curing agent will lead to bubble formation in the PDMS mixture. These bubbles need to be removed before the PDMS polymerizes. The PDMS can be degassed after pouring it on top of the wafer by placing the Petri dish in a desiccator connected to a vacuum pump. With this setup, it takes about 30 min to remove all bubbles from the mixture.</li>
	<li>Polymerize the PDMS by placing the Petri dish with the wafer on top of a hot plate at 120 &deg;C for 1 hr and then at 65 &deg;C for another hour.</li>
	<li>Remove the aluminum foil together with the wafer and polymerized PDMS from the glass Petri dish. Peel off the aluminum foil and the thin residual layer of polymerized PDMS from the back of the wafer. The layer of PDMS on top of the wafer can then be separated from the wafer by lifting it up carefully.</li>
	<li>Place the PDMS layer upside down (with the channels facing up) on the bench and cut out the single chip designs imprinted on the PDMS carefully with a scalpel. Try to retain about 3 mm of PDMS around the edges of the channels to improve attachment of the chip to the cover glass later on.</li>
	<li>Punch holes in the PDMS at the ends of the inlet, outlet and side channel (Figure 2A) by pushing a 20 Gauge Luer stub all the way through the PDMS in a straight manner.</li>
</ol>
Make sure the PDMS chip is still lying upside down on the bench while punching the holes. This prevents PDMS from sticking to the inside of the channel, which could cause blockage of the channel.
<ol start="9">
	<li>After punching each hole, remove the column of PDMS in the Luer stub with tweezers before pulling the stub out again. The PDMS column could otherwise stay behind and block the just punched hole.</li>
	<li>Clean the surfaces of the chip from dust particles and residual PDMS by placing scotch tape on it and immediately removing the tape again. Similarly clean the cover glass to which the chip will be attached.</li>
	<li>Place the cleaned chip and cover glass below the UV lamp of the Benchtop UV-Ozone Cleaner. The sides that need to be bonded together must face the lamp.</li>
	<li>Expose the PDMS and cover glass to the UV light for 6-8 min and directly afterwards put the chip on the cover glass by placing the exposed surfaces on top of each other.</li>
	<li>Gently tap around the sides of the chip to promote attachment of the PDMS to the cover glass and to remove any air bubbles. Do not tap on top of the channel structure as this may cause the micropads to get attached to the cover glass as well.</li>
	<li>Place the newly made microfluidic setup on a hot plate at 100 &deg;C for 60 min. Test the strength of the bonding between the cover glass and PDMS chip by trying to lift up the edges of the PDMS chip slightly. When the PDMS block cannot be lifted from the glass surface, the bonding is successful and the chip is ready for use.</li>
</ol>
3. Preparing the Chip for Cell Loading
Failure of a microfluidic device can potentially cause leakage of medium into the microscope. To avoid this, it is advisory to use a metal holder and/or seal the sides of the chip where the PDMS meets the glass with nail polish or epoxy glue. This prevents leakage of medium in case the PDMS chip is not bonded well enough to the cover glass. Also the tubing connections can be secured around the insertion points in a similar manner to avoid leakage of medium. A home-made water sensor that switches off the syringe pump in case of leakage can be used as an extra safety precaution. Drawings of the metal holder especially designed for the microfluidic chip can be obtained from the authors.
<ol>
	<li>Place the microfluidic chip in the metal holder, with silicone gel between the glass of the chip and the metal parts of the holder to create a waterproof seal. Screw the nuts gently, not to break the glass.</li>
	<li>Connect thin tubes (ca. 5-15 cm long) to the side channel and the outlet channel of the chip. The use of tweezers makes it easier to insert the tubing in the punched holes.</li>
	<li>Fill a 50 ml Luer-Lok syringe with culture medium, remove the air from the syringe and connect it sequentially to a syringe filter, a 20 Gauge Luer stub, a short thick tube (ca. 2 cm long) and a thin tube. Make sure that the thin tube is long enough to span the distance between the syringe pump and the microscope stage.</li>
	<li>Place the syringe in the syringe pump, fast forward the pump until the thin tube is completely filled with medium.</li>
	<li>Push the thin tube connected to the syringe into the inlet channel of the chip and let the medium flow through the chip at 10 &mu;l/min (Figure 2B). Collect the medium leaving the chip (e.g. in a Petri dish). The medium will run out via the side channel because of the resistance difference between the Tough-Tag made large side channel and the outlet channel.</li>
	<li>Place the chip in the microscope stage and set the focus of the microscope on the pads.</li>
</ol>
The use of oil immersion objectives is preferred over that of water immersion objectives because oil will not dry out over the time-course of the experiment.
Depending on the microscope there might be issues with retaining the focus during the initial hours of the experiment. It is therefore advisable to leave the chip for one to two hours in the microscope stage so it can settle down before loading cells and starting the experiment.
4. Loading of Yeast Cells into the Microfluidic Chip
<ol>
	<li>Connect a 5 ml Luer tip syringe to a 20 Gauge Luer stub and a thick tube (ca. 3 cm).</li>
	<li>Take a sample of the cell culture to be loaded into the chip.</li>
</ol>
The preferred cell count for loading is between 1-5 x 106 cells per ml. Cultures with higher cell counts need to be diluted before loading. When culturing cells on YPD, cell loading efficiency can be improved many-fold if cells are first washed with and resuspended in minimal medium containing a similar glucose percentage before loading. During operation of the chip, YPD medium can again be safely used.
<ol start="3">
	<li>Load approximately 1 ml of the cell suspension into the syringe and remove all the air from the syringe.</li>
	<li>Decrease the flow rate of the syringe pump to 0.5 &mu;l/min. The low and continued flow enforced by the syringe pump during loading (in step 4.5) will push non-attached cells out via the side channel (Figure 2C).</li>
	<li>Connect the syringe containing the cell suspension to the tube of the outlet channel. Load the cells by pressing on the plunger of the syringe gently. Observe the cells coming in and settling underneath the micropads via the ocular or via the computer screen.</li>
	<li>Maintain pressure on the plunger until sufficient cells settle underneath the pads. The optimum load is 1-3 cells per pad. As cells settle underneath the pads randomly, it is quite common that a few pads do not contain any cells and other pads are completely filled with cells.</li>
	<li>Disconnect the syringe used for cell loading and the thick tube connected to it from the thin tubing of the outlet channel, flush the side channel for a couple of minutes at higher flow rates (10 &mu;l/min) to remove air bubbles and/or cells that did not yet exit the chip (Figure 2B). If cells are not removed from the side channel, they can start to grow in the side channel and interfere with the experiment later on.</li>
	<li>Put the flow of the syringe pump back down to 0.5 &mu;l/min and close the side channel off by connecting it to a thick tube (ca. 5 cm long) containing a catheter plug at its end (Figure 2D).</li>
	<li>Increase the flow to a final flow rate of 1-5 &mu;l/min. Flow rates may vary depending on medium and yeast strain.</li>
	<li>Start a movie with the microscope and camera settings suitable for the goal of the experiment. Make sure that the speed of the microscope stage is set to such a low speed that the oil can follow. For determination of replicative lifespan, image cells every 10 min. To protect cells from the minute amounts of UV light emitted by the halogen lamp, which is used during DIC acquisition, it is advisable to place an additional UV filter in the light path. When using fluorescence microscopy, it is preferred to image the cells less frequently (e.g. every 20 min) to avoid phototoxic effects. The experiment is completed when all cells loaded at the start of the experiment are dead, which under normal conditions takes up to 5 days. It is recommended to regularly check the focus of the images during the experiment and if necessary adjust it.</li>
</ol>

<ol>
	<li>Kaeberlein, M., McVey, M., Guarente, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Using+yeast+to+discover+the+fountain+of+youth.">Using yeast to discover the fountain of youth.</a> Sci. Aging Knowledge Environ. 2001 (1), pe1 (2001).</li><li>Mortimer, R. K., Johnston, J. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Life+span+of+individual+yeast+cells.">Life span of individual yeast cells.</a> Nature. 183 (4677), 1751-1752 (1959).</li><li>Steffen, K. K., Kennedy, B. K., Kaeberlein, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measuring+replicative+life+span+in+the+budding+yeast.">Measuring replicative life span in the budding yeast.</a> J. Vis. Exp. (28), e1209 (2009).</li><li>Lee, S. S., Avalos Vizcarra, I., Huberts, D. H., Lee, L. P., Heinemann, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Whole+lifespan+microscopic+observation+of+budding+yeast+aging+through+a+microfluidic+dissection+platform.">Whole lifespan microscopic observation of budding yeast aging through a microfluidic dissection platform.</a> Proc. Natl. Acad. Sci. U.S.A. 109 (13), 4916-4920 (2012).</li><li>Xie, Z., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Molecular+phenotyping+of+aging+in+single+yeast+cells+using+a+novel+microfluidic+device.">Molecular phenotyping of aging in single yeast cells using a novel microfluidic device.</a> Aging Cell. , (2012).</li><li>Xia, Y., Whitesides, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Soft+Lithography.">Soft Lithography.</a> Angewandte Chemie International Edition. 37 (5), 550-575 (1998).</li><li>Mata, A., Fleischman, A. J., Roy, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fabrication+of+multi-layer+SU-8+microstructures.">Fabrication of multi-layer SU-8 microstructures.</a> Journal of Micromechanics and Microengineering. 16 (2), 276-284 (2006).</li><li>Huang, Y., Agrawal, B., Clark, P. A., Williams, J. C., Kuo, J. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Evaluation+of+cancer+stem+cell+migration+using+compartmentalizing+microfluidic+devices+and+live+cell+imaging.">Evaluation of cancer stem cell migration using compartmentalizing microfluidic devices and live cell imaging.</a> J. Vis. Exp. (58), e3297 (2011).</li><li>Kaeberlein, M., Kirkland, K. T., Fields, S., Kennedy, B. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Genes+determining+yeast+replicative+life+span+in+a+long-lived+genetic+background.">Genes determining yeast replicative life span in a long-lived genetic background.</a> Mechanisms of Ageing and Development. 126 (4), 491-504 (2005).</li><li>Scheckhuber, C. Q., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Reducing+mitochondrial+fission+results+in+increased+life+span+and+fitness+of+two+fungal+ageing+models.">Reducing mitochondrial fission results in increased life span and fitness of two fungal ageing models.</a> Nat. Cell Biol. 9 (1), 99-105 (2007).</li><li>Defossez, P. A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Elimination+of+replication+block+protein+Fob1+extends+the+life+span+of+yeast+mother+cells.">Elimination of replication block protein Fob1 extends the life span of yeast mother cells.</a> Mol. Cell. 3 (4), 447-455 (1999).</li><li>Kaeberlein, M., McVey, M., Guarente, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+SIR2/3/4+complex+and+SIR2+alone+promote+longevity+in+Saccharomyces+cerevisiae+by+two+different+mechanisms.">The SIR2/3/4 complex and SIR2 alone promote longevity in Saccharomyces cerevisiae by two different mechanisms.</a> Genes Dev. 13 (19), 2570-2580 (1999).</li><li>Shcheprova, Z., Baldi, S., Frei, S. B., Gonnet, G., Barral, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+mechanism+for+asymmetric+segregation+of+age+during+yeast+budding.">A mechanism for asymmetric segregation of age during yeast budding.</a> Nature. 454 (7205), 728-734 (2008).</li><li>Vanoni, M., Vai, M., Popolo, L., Alberghina, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Structural+heterogeneity+in+populations+of+the+budding+yeast+Saccharomyces+cerevisiae.">Structural heterogeneity in populations of the budding yeast Saccharomyces cerevisiae.</a> J. Bacteriol. 156 (3), 1282-1291 (1983).</li><li>Huh, W. K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Global+analysis+of+protein+localization+in+budding+yeast.">Global analysis of protein localization in budding yeast.</a> Nature. 425 (6959), 686-691 (2003).</li><li>Zhang, Y., Luo, C., Zou, K., Xie, Z., Brandman, O., Ouyang, Q., Li, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Single+cell+analysis+of+yeast+replicative+aging+using+a+new+generation+of+microfluidic+device.">Single cell analysis of yeast replicative aging using a new generation of microfluidic device.</a> PLoS One. 7 (11), e48275 (2012).</li></ol>

The authors declare that they have no competing financial interests.

The microfluidic method described here is an important novel tool in aging research as it enables simple and automated generation of yeast replicative lifespan data in combination with continuous high resolution imaging. These attributes are major improvements over the experimental possibilities of the classical dissection method, yet there are a few limitations of the method that need to be taken into account.
Note that the determined replicative lifespan can be affected by the efficiency of ...

Budding yeast is an important model organism for aging research1. Until recently studying replicative aging in yeast cells was a laborious process requiring a dissection method, in which each bud was manually removed from the mother cell2,3. To solve this problem, we recently presented a novel microfluidic setup able to track individual mother cells throughout their entire lifespan4.
In our microfluidic chip, yeast cells are trapped under soft elastomer-based micropads (see Figure 1). A continuous flow of medium washes away newly formed daughter cells and provides the cells with fresh nutrients. In a single experiment, up to 50 mother cells can be monitored in a fully automated manner throughout their entire replicative lifespan. Due to the excellent optical properties of the microfluidic chip, it is possible to simultaneously monitor different aspects of yeast cell biology (e.g. by using fluorescent proteins).
 
Compared to the classical dissection method, the microfluidic setup provides substantial advantages. It ensures a defined and constant environment during the whole aging experiment. It requires no expensive specialized equipment and can be run on any microscope equipped with automated focus and time-lapse abilities as well as temperature-control for cell cultivation. The production and operation of the microfluidic chips can be learned within a few days. In addition, cells can be directly loaded from an exponentially growing culture, an advantage over another recently published microfluidic method5, which requires biotinylation of mother cells.a Combined with high-resolution imaging, the here described method can be used to measure gradual changes in cellular morphology, protein expression and localization during yeast aging in an unprecedented manner. The capability for long-term monitoring of single cells also provides unique possibilities for yeast cell cycle studies.
aThis method has recently been optimized to remove the biotinylation from the protocol16, which was published while this manuscript was in review.

<table border="1">
 <tbody>
 <tr>
 <td>Name </td>
 <td>Company </td>
 <td>Catalogue number </td>
 <td>Comments </td>
 </tr>
 <tr>
 <td></td>
 <td></td>
 <td></td>
 <td>REAGENTS</td>
 </tr>
 <tr>
 <td>DC Sylgard 184 elastomer </td>
 <td>Mavom bv </td>
 <td>1060040 </td>
 <td>This package contains PDMS base and PDMS curing agent.</td>
 </tr>
 <tr>
 <td>Glass Petri dishes 120/20 mm </td>
 <td>VWR International </td>
 <td>391-2850 </td>
 <td></td>
 </tr>
 <tr>
 <td>Cover glasses 22x40 mm </td>
 <td>CBN Labsuppliers BV </td>
 <td>190002240 </td>
 <td></td>
 </tr>
 <tr>
 <td>Tough-Tags </td>
 <td>Sigma-Aldrich </td>
 <td>Z359106 </td>
 <td></td>
 </tr>
 <tr>
 <td>Aluminum foil </td>
 <td></td>
 <td></td>
 <td></td>
 </tr>
 <tr>
 <td>Plastic disposable cup </td>
 <td></td>
 <td></td>
 <td></td>
 </tr>
 <tr>
 <td>Serological pipette 5 ml </td>
 <td>VWR International </td>
 <td>612-1245 </td>
 <td></td>
 </tr>
 <tr>
 <td>Scotch tape </td>
 <td>VWR International </td>
 <td>819-1460 </td>
 <td></td>
 </tr>
 <tr>
 <td>Baysilone paste (GE Bayer silicones) </td>
 <td>Sigma-Aldrich </td>
 <td>85403-1EA </td>
 <td></td>
 </tr>
 <tr>
 <td>PTFE microbore tubing, 0.012"ID x 0.030"OD </td>
 <td>Cole Parmer </td>
 <td>EW-06417-11 </td>
 <td>Referred to as thin tubing </td>
 </tr>
 <tr>
 <td>Tygon microbore Tubing, 0.030"ID x 0.090"OD </td>
 <td>Cole Parmer </td>
 <td>EW-06418-03 </td>
 <td>Referred to as thick tubing </td>
 </tr>
 <tr>
 <td>Scalpel </td>
 <td>VWR International </td>
 <td>233-5334 </td>
 <td></td>
 </tr>
 <tr>
 <td>50 ml Luer-Lok syringes </td>
 <td>BD </td>
 <td>300137 </td>
 <td></td>
 </tr>
 <tr>
 <td>5 ml syringes, Luer tip </td>
 <td>VWR International </td>
 <td>613-1599 </td>
 <td></td>
 </tr>
 <tr>
 <td>Tweezers </td>
 <td>VWR International </td>
 <td>232-2132 </td>
 <td></td>
 </tr>
 <tr>
 <td>20 Gauge Luer stubs </td>
 <td>Instech Solomon </td>
 <td>LS20 </td>
 <td></td>
 </tr>
 <tr>
 <td>Syringe filters (pore size 0.20 &mu;m) </td>
 <td>Sigma-Aldrich </td>
 <td>16534K </td>
 <td></td>
 </tr>
 <tr>
 <td>Stainless steel catheter Plug, 20 ga x12 mm </td>
 <td>Instech Solomon </td>
 <td>SP20/12 </td>
 <td></td>
 </tr>
 <tr>
 <td>Petri dishes </td>
 <td>VWR International </td>
 <td>391-0892 </td>
 <td></td>
 </tr>
 <tr>
 <td></td>
 <td></td>
 <td></td>
 <td> EQUIPMENT</td>
 </tr>
 <tr>
 <td>Benchtop UV-Ozone Cleaner </td>
 <td>NOVA Scan </td>
 <td>PSD-UVT </td>
 <td></td>
 </tr>
 <tr>
 <td>Harvard Pump 11 Elite </td>
 <td>Harvard Apparatus </td>
 <td>70-4505 </td>
 <td></td>
 </tr>
 <tr>
 <td>SU-8 silicon master mold (wafer) </td>
 <td></td>
 <td></td>
 <td>Self-made; For details contact corresponding author </td>
 </tr>
 <tr>
 <td>Balance </td>
 <td>Sartorius corporation </td>
 <td>ED4202S </td>
 <td></td>
 </tr>
 <tr>
 <td>Vacuum pump </td>
 <td>KNF Neuberger </td>
 <td>N022 AN.18 </td>
 <td></td>
 </tr>
 <tr>
 <td>Desiccator </td>
 <td>VWR International </td>
 <td>467-2115 </td>
 <td></td>
 </tr>
 <tr>
 <td>Hot plate </td>
 <td>VWR International </td>
 <td>460-3267 </td>
 <td></td>
 </tr>
 <tr>
 <td>Optional: Metal holder for cover glass (22x40 mm) </td>
 <td></td>
 <td></td>
 <td>Self-made; For details contact corresponding author </td>
 </tr>
 <tr>
 <td>(Fluorescence) Microscope with 60x objective, autofocus, time-lapse abilities and preferably an automated (motorized XY control) stage </td>
 <td>Nikon </td>
 <td>Eclipse Ti-E </td>
 <td></td>
 </tr>
 </tbody>
</table>

continuous high-resolution microscopic observation of replicative aging in budding yeast

We demonstrate the use of a simple microfluidic setup, in which single budding yeast cells can be tracked throughout their entire lifespan. The microfluidic chip exploits the size difference between mother and daughter cells using an array of micropads. Upon loading, cells are trapped underneath these micropads, because the distance between the micropad and cover glass is similar to the diameter of a yeast cell (3-4 &mu;m). After the loading procedure, culture medium is continuously flushed through the chip, which not only creates a constant and defined environment throughout the entire experiment, but also flushes out the emerging daughter cells, which are not retained underneath the pads due to their smaller size. The setup retains mother cells so efficiently that in a single experiment up to 50 individual cells can be monitored in a fully automated manner for 5 days or, if necessary, longer. In addition, the excellent optical properties of the chip allow high-resolution imaging of cells during the entire aging process.

In this protocol, cells are loaded into the microfluidic chip directly from mid-exponential culture. To ascertain whether the age distribution of cells trapped in the microfluidic chip is similar to that of the culture prior to loading, cells were stained with wheat agglutinin conjugated to FITC (WGA-FITC) to visualize bud scars. As can be seen in Figure 3, the entrapment of cells under the micropads of the microfluidic chip is not biased to cells of a certain age.
Replicative...

Watch this Scientific Journal Video about Continuous High-resolution Microscopic Observation of Replicative Aging in Budding Yeast at JoVE.com

Continuous High-resolution Microscopic Observation of Replicative Aging in Budding Yeast

We describe here the operation of a microfluidic device that allows continuous and high-resolution microscopic imaging of single budding yeast cells during their complete replicative and/or chronological lifespan.

We demonstrate the use of a simple microfluidic setup, in which single budding yeast cells can be tracked throughout their entire lifespan. The ...

continuous-high-resolution-microscopic-observation-replicative-aging

Research

JoVE Journal

Bioengineering

12.8K 조회수.  University of Groningen. 우리는 여기에서 자신의 완전한 증식하는 및 / 또는 연대순 수명 기간 동안 하나의 신진 효모 세포의 연속 고해상도 현미경 이미징을 허용 microfluidic 장치의 동작을 설명합니다.

비디오: Continuous High-resolution Microscopic Observation of Replicative Aging in Budding Yeast

High-resolution Fiber-optic Microendoscopy for in situ Cellular Imaging

Many biological and clinical studies require the longitudinal study and analysis of morphology and function with cellular level resolution. Traditionally, multiple experiments are run in parallel, with individual samples removed from the study at sequential time points for evaluation by light microscopy. Several intravital techniques have been developed, with confocal, multiphoton, and second harmonic microscopy all demonstrating their ability to be used for imaging in situ 1. With these systems, however, the required infrastructure is complex and expensive, involving scanning laser systems and complex light sources. Here we present a protocol for the design and assembly of a high-resolution microendoscope which can be built in a day using off-the-shelf components for under US$5,000. The platform offers flexibility in terms of image resolution, field-of-view, and operating wavelength, and we describe how these parameters can be easily modified to meet the specific needs of the end user.
We and others have explored the use of the high-resolution microendoscope (HRME) in in vitro cell culture 2-5, in excised 6 and living animal tissues 2,5, and in human tissues in vivo 2,7. Users have reported the use of several different fluorescent contrast agents, including proflavine 2-4, benzoporphyrin-derivative monoacid ring A (BPD-MA) 5, and fluoroscein 6,7, all of which have received full, or investigational approval from the FDA for use in human subjects. High-resolution microendoscopy, in the form described here, may appeal to a wide range of researchers working in the basic and clinical sciences. The technique offers an effective and economical approach which complements traditional benchtop microscopy, by enabling the user to perform high-resolution, longitudinal imaging in situ.

High-resolution Fiber-optic Microendoscopy for in situ Cellular Imaging

In many biological and clinical situations it is advantageous to study cellular processes as they evolve in their native microenvironment. Here we describe the assembly and use of a low-cost fiber-optic microscope which can provide real time imaging in cell culture, animal studies, and clinical patient studies.

고해상도 광섬유 Microendoscopy에 대한 현장에서 세포 이미징

Many biological and clinical studies require the longitudinal study and analysis of morphology and function with cellular level resolution.  ...

연구

생체공학

High Resolution 3D Imaging of Ex-Vivo Biological Samples by Micro CT

Non-destructive volume visualization can be achieved only by tomographic techniques, of which the most efficient is the x-ray micro computerized tomography (&mu;CT).
High resolution &mu;CT is a very versatile yet accurate (1-2 microns of resolution) technique for 3D examination of ex-vivo biological samples1, 2. As opposed to electron tomography, the &mu;CT allows the examination of up to 4 cm thick samples. This technique requires only few hours of measurement as compared to weeks in histology. In addition, &mu;CT does not rely on 2D stereologic models, thus it may complement and in some cases can even replace histological methods3, 4, which are both time consuming and destructive. Sample conditioning and positioning in &mu;CT is straightforward and does not require high vacuum or low temperatures, which may adversely affect the structure. The sample is positioned and rotated 180&deg; or 360&deg;between a microfocused x-ray source and a detector, which includes a scintillator and an accurate CCD camera, For each angle a 2D image is taken, and then the entire volume is reconstructed using one of the different available algorithms5-7. The 3D resolution increases with the decrease of the rotation step. The present video protocol shows the main steps in preparation, immobilization and positioning of the sample followed by imaging at high resolution.

High Resolution 3D Imaging of Ex-Vivo Biological Samples by Micro CT

Non-destructive volume visualization can be achieved only by tomographic techniques, of which the most efficient is the x-ray micro computerized tomography ( CT).

고해상도 3D 영상의 전 VIVO</em마이크로 중부 표준시로> 생물 학적 샘플

Non-destructive volume visualization can be achieved only by tomographic techniques, of which the most efficient is the x-ray micro computerized ...

High-resolution Spatiotemporal Analysis of Receptor Dynamics by Single-molecule Fluorescence Microscopy

Single-molecule microscopy is emerging as a powerful approach to analyze the behavior of signaling molecules, in particular concerning those aspect (e.g., kinetics, coexistence of different states and populations, transient interactions), which are typically hidden in ensemble measurements, such as those obtained with standard biochemical or microscopy methods. Thus, dynamic events, such as receptor-receptor interactions, can be followed in real time in a living cell with high spatiotemporal resolution. This protocol describes a method based on labeling with small and bright organic fluorophores and total internal reflection fluorescence (TIRF) microscopy to directly visualize single receptors on the surface of living cells. This approach allows one to precisely localize receptors, measure the size of receptor complexes, and capture dynamic events such as transient receptor-receptor interactions. The protocol provides a detailed description of how to perform a single-molecule experiment, including sample preparation, image acquisition and image analysis. As an example, the application of this method to analyze two G-protein-coupled receptors, i.e., &#946;2-adrenergic and &#947;-aminobutyric acid type B (GABAB) receptor, is reported. The protocol can be adapted to other membrane proteins and different cell models, transfection methods and labeling strategies.

This protocol describes how to use total internal reflection fluorescence microscopy to visualize and track single receptors on the surface of living cells and thereby analyze receptor lateral mobility, size of receptor complexes as well as to visualize transient receptor-receptor interactions. This protocol can be extended to other membrane proteins.

단일 분자 형광 현미경에 의한 수용체 역학의 고해상도 시공간 분석

Single-molecule microscopy is emerging as a powerful approach to analyze the behavior of signaling molecules, in particular concerning those aspect (e.g., ...

Preparation of Mica Supported Lipid Bilayers for High Resolution Optical Microscopy Imaging

Supported lipid bilayers (SLBs) are widely used as a model for studying membrane properties (phase separation, clustering, dynamics) and its interaction with other compounds, such as drugs or peptides. However SLB characteristics differ depending on the support used. 
Commonly used techniques for SLB imaging and measurements are single molecule fluorescence microscopy, FCS and atomic force microscopy (AFM). Because most optical imaging studies are carried out on a glass support, while AFM requires an extremely flat surface (generally mica), results from these techniques cannot be compared directly, since the charge and smoothness properties of these materials strongly influence diffusion. Unfortunately, the high level of manual dexterity required for the cutting and gluing thin slices of mica to the glass slide presents a hurdle to routine use of mica for SLB preparation. Although this would be the method of choice, such prepared mica surfaces often end up being uneven (wavy) and difficult to image, especially with small working distance, high numerical aperture lenses. Here we present a simple and reproducible method for preparing thin, flat mica surfaces for lipid vesicle deposition and SLB preparation. Additionally, our custom made chamber requires only very small volumes of vesicles for SLB formation. The overall procedure results in the efficient, simple and inexpensive production of high quality lipid bilayer surfaces that are directly comparable to those used in AFM studies.

We present a method of preparing mica supported lipid bilayers for high resolution microscopy. Mica is transparent and flat on an atomic scale, but rarely used in imaging because of handling difficulties; our preparation results in even deposition of the mica sheet, and reduces the material used in bilayer preparation.

운모의 준비 고해상도 광학 현미경 이미징 지질 이중층 지원

Supported lipid bilayers (SLBs) are widely used as a model for studying membrane properties (phase separation, clustering, dynamics) and its interaction ...

Nutrient Regulation by Continuous Feeding for Large-scale Expansion of Mammalian Cells in Spheroids

In this demonstration, spheroids formed from the &#946;-TC6 insulinoma cell line were cultured as a model of manufacturing a mammalian islet cell product to demonstrate how regulating nutrient levels can improve cell yields. In previous studies, bioreactors facilitated increased culture volumes over static cultures, but no increase in cell yields were observed. Limitations in key nutrients such as glucose, which were consumed between batch feedings, can lead to limitations in cell expansion. Large fluctuations in glucose levels were observed, despite the increase in glucose concentrations in the media. The use of continuous feeding systems eliminated fluctuations in glucose levels, and improved cell growth rates when compared with batch fed static and SSB culture methods. Additional increases in growth rates were observed by adjusting the feed rate based on calculated nutrient consumption, which allowed the maintenance of physiological glucose over three weeks in culture. This method can also be adapted for other cell types.

Nutrient regulation using continuous growth adjusted feeding improves growth rates of mammalian cell spheroids compared to intermittent batch feeding for cultures in stirred suspension bioreactors. This study demonstrates the methods required for establishing simple adjusted rate fed cultures.

회전 타원체의 포유 동물 세포의 대규모 확장을위한 지속적인 공급함으로써 영양 규정

In this demonstration, spheroids formed from the &#946;-TC6 insulinoma cell line were cultured as a model of manufacturing a mammalian islet cell product ...

Proper Positioning and Restraint of a Rat Hind Limb for Focused High Resolution Imaging of Bone Micro-architecture Using In Vivo Micro-computed Tomography

The use of in vivo micro-computed tomography (&#181;CT) is a powerful tool which involves the non-destructive imaging of internal structures at high resolutions in live animal models. This allows for repeated imaging of the same rodent over time. This feature not only reduces the total number of rodents required in an experimental design and thereby reduces the inter-subject variation that can arise, but also allows researchers to assess longitudinal or life-long responses to an intervention. To acquire high quality images that can be processed and analyzed to more accurately quantify outcomes of bone micro-architecture, users of in vivo &#181;CT scanners must properly anesthetize the rat, and position and restrain the hind limb. To do this, it is imperative that the rat be anesthetized to a level of complete relaxation, and that pedal reflexes are lost. These guidelines may be modified for each individual rat, as the rate of isoflurane metabolism can vary depending on strain and body size. Proper technique for in vivo &#181;CT image acquisition enables accurate and consistent measurement of bone micro-architecture within and across studies.

Proper Positioning and Restraint of a Rat Hind Limb for Focused High Resolution Imaging of Bone Micro-architecture Using In Vivo Micro-computed Tomography

This paper instructs users of in vivo micro-computed tomography (&#181;CT) scanners how to anesthetize, correctly position and restrain the hind limb of a rat for minimal movement during high-resolution imaging of the tibia. The result is high quality images that can be processed to accurately quantify bone micro-architecture.

적절 한 위치와 뼈 마이크로 아키텍처를 사용 하 여 생체 내에서 마이크로-단층의 집중된 고해상도 이미징 쥐 뒷 다리의 구속

The use of in vivo micro-computed tomography (&#181;CT) is a powerful tool which involves the non-destructive imaging of internal structures at high ...

High Resolution 3D Imaging of the Human Pancreas Neuro-insular Network

Using traditional histological methods, researchers are hampered in their ability to image whole tissues or organs in large-scale 3D. Histological sections are generally limited to &#60;20 &#181;m as formalin fixed paraffin section on glass slides or &#60;500 &#181;m for free-floating fixed sections. Therefore, extensive efforts are required for serial sectioning and large-scale image reconstruction methods to recreate 3D for samples &#62;500 &#181;m using traditional methods. In addition, light scatters from macromolecules within tissues, particularly lipids, prevents imaging to a depth &#62;150 &#181;m with most confocal microscopes. To reduce light scatter and to allow for deep tissue imaging using simple confocal microscopy, various optical clearing methods have been developed that are relevant for rodent and human tissue samples fixed by immersion. Several methods are related and use protein crosslinking with acrylamide and tissue clearing with sodium dodecyl sulfate (SDS). Other optical clearing techniques used various solvents though each modification had various advantages and disadvantages. Here, an optimized passive optical clearing method is described for studies of the human pancreas innervation and specifically for interrogation of the innervation of human islets.

Here, we present a protocol to image human pancreas sections in three dimensions (3D) using optimized passive clearing methods. This manuscript demonstrates these procedures for passive optical clearing followed by multiple immunofluorescence staining to identify key elements of the autonomic and sensory neural networks innervating human islets.

인간의 췌 장 신경 섬 네트워크의 고해상도 3D 이미징

Using traditional histological methods, researchers are hampered in their ability to image whole tissues or organs in large-scale 3D. Histological ...

High-resolution Patterning Using Two Modes of Electrohydrodynamic Jet: Drop on Demand and Near-field Electrospinning

Electrohydrodynamic (EHD) jet printing has drawn attention in various fields because it can be used as a high-resolution and low-cost direct patterning tool. EHD printing uses a fluidic supplier to maintain the extruded meniscus by pushing the ink out of the nozzle tip. The electric field is then used to pull the meniscus down to the substrate to produce high-resolution patterns. Two modes of EHD printing have been used for fine patterning: continuous near-field electrospinning (NFES) and dot-based drop-on-demand (DOD) EHD printing. According to the printing modes, the requirements for the printing equipment and ink viscosity will differ. Even though two different modes can be implemented with a single EHD printer, the realization methods significantly differ in terms of ink, fluidic system, and driving voltage. Consequently, without a proper understanding of the jetting requirements and limitations, it is difficult to obtain the desired results. The purpose of this paper is to present a guideline so that inexperienced researchers can reduce the trial and error efforts to use the EHD jet for their specific research and development purposes. To demonstrate the fine-patterning implementation, we use Ag nanoparticle ink for the conductive patterning in the protocol. In addition, we also present the generalized printing guidelines that can be used for other types of ink for various fine-patterning applications.

Here, we present a protocol to produce high-resolution conductive patterns using electrohydrodynamic (EHD) jet printing. The protocol includes two modes of EHD jet printing: the continuous near-field electrospinning (NFES) and the dot-based drop-on-demand (DOD) EHD printing.

충돌기 제트의 두 가지 모드를 사용 하 여 패턴 고해상도: 수요와 근처-필드 전기에

Electrohydrodynamic (EHD) jet printing has drawn attention in various fields because it can be used as a high-resolution and low-cost direct patterning ...

High-resolution Patterned Biofilm Deposition Using pDawn-Ag43

Spatial structure and patterning play an important role in bacterial biofilms. Here we demonstrate an accessible method for culturing E. coli biofilms into arbitrary spatial patterns at high spatial resolution. The technique uses a genetically encoded optogenetic construct&#8212;pDawn-Ag43&#8212;that couples biofilm formation in E. coli to optical stimulation by blue light. We detail the process for transforming E. coli with&#160;pDawn-Ag43, preparing the required optical set-up, and the protocol for culturing patterned biofilms using pDawn-Ag43 bacteria. Using this protocol, biofilms with a spatial resolution below 25 &#956;m can be patterned on various surfaces and environments, including enclosed chambers, without requiring microfabrication, clean-room facilities, or surface pretreatment. The technique is convenient and appropriate for use in applications that investigate the effect of biofilm structure, providing tunable control over biofilm patterning. More broadly, it also has potential applications in biomaterials, education, and bio-art.

We demonstrate a method for depositing Escherichia coli bacterial biofilms in arbitrary spatial patterns with a high resolution using optical stimulation of a genetically encoded surface-adhesion construct.

고해상도 무늬 Biofilm 증 착을 사용 하 여 pDawn-Ag43

Spatial structure and patterning play an important role in bacterial biofilms. Here we demonstrate an accessible method for culturing E. coli biofilms ...

High-resolution Imaging of Nuclear Dynamics in Live Cells under Uniaxial Tensile Strain

Extracellular mechanical strain is known to elicit cell phenotypic responses and has physiological relevance in several tissue systems. To capture the effect of applied extracellular tensile strain on cell populations in vitro via biochemical assays, a device has previously been designed which can be fabricated simply and is small enough to fit inside tissue culture incubators, as well as on top of microscope stages. However, the previous design of the polydimethylsiloxane substratum did not allow high-resolution subcellular imaging via oil-immersion objectives. This work describes a redesigned geometry of the polydimethylsiloxane substratum and a customized imaging setup that together can facilitate high-resolution subcellular imaging of live cells while under applied strain. This substratum can be used with the same, earlier designed device and, hence, has the same advantages as listed above, in addition to allowing high-resolution optical imaging. The design of the polydimethylsiloxane substratum can be improved by incorporating a grid which will facilitate tracking the same cell before and after the application of strain. Representative results demonstrate high-resolution time-lapse imaging of fluorescently labeled nuclei within strained cells captured using the method described here. These nuclear dynamics data give insights into the mechanism by which applied tensile strain promotes differentiation of oligodendrocyte progenitor cells.&#160;

Using a previously designed device to apply mechanical strain to adherent cells, this paper describes a redesigned substratum geometry and a customized apparatus for high-resolution single-cell imaging of strained cells with a 100x oil immersion objective.

일축 인장 스트레인 하에서 살아있는 세포의 핵 역학에 대 한 고해상도 이미징

Extracellular mechanical strain is known to elicit cell phenotypic responses and has physiological relevance in several tissue systems. To capture the ...