Photochemical Oxidative Growth of Iridium Oxide Nanoparticles on CdSe@CdS Nanorods

Summary

A protocol for the photochemical oxidative growth of small crystalline iridium oxide nanoparticles on the surface of CdSe@CdS seeded rod nanoparticles is presented.

Abstract

We demonstrate a procedure for the photochemical oxidative growth of iridium oxide catalysts on the surface of seeded cadmium selenide-cadmium sulfide (CdSe@CdS) nanorod photocatalysts. Seeded rods are grown using a colloidal hot-injection method and then moved to an aqueous medium by ligand exchange. CdSe@CdS nanorods, an iridium precursor and other salts are mixed and illuminated. The deposition process is initiated by absorption of photons by the semiconductor particle, which results with formation of charge carriers that are used to promote redox reactions. To insure photochemical oxidative growth we used an electron scavenger. The photogenerated holes oxidize the iridium precursor, apparently in a mediated oxidative pathway. This results in the growth of high quality crystalline iridium oxide particles, ranging from 0.5 nm to about 3 nm, along the surface of the rod. Iridium oxide grown on CdSe@CdS heterostructures was studied by a variety of characterization methods, in order to evaluate its characteristics and quality. We explored means for control over particle size, crystallinity, deposition location on the CdS rod, and composition. Illumination time and excitation wavelength were found to be key parameters for such control. The influence of different growth conditions and the characterization of these heterostructures are described alongside a detailed description of their synthesis. Of significance is the fact that the addition of iridium oxide afforded the rods astounding photochemical stability under prolonged illumination in pure water (alleviating the requirement for hole scavengers).

Introduction

Photocatalysis presents an attractive and promising solution for renewable energy generation and other environmental applications such as water treatment and air purification^1-3. Overall water splitting, driven by solar energy, could be a source of clean and renewable hydrogen fuel; however, despite decades of research, systems that are sufficiently stable and efficient for practical use have not yet been realized.

Both photodeposition and semiconductor-mediated photocatalysis rely on the same mechanism of separating photo-generated electron-hole pairs and driving them to the surface where they can initiate redox reactions. The similarities between these two processes make photodeposition an attractive synthetic tool for the field of photocatalysis^4-6. This method is expected to take photocatalyst production to new and unexplored frontiers. It might potentially offer pristine control over the spatial arrangement of the different components in a heterostructures, and advance the ability to construct sophisticated nanoparticle systems. Ultimately the method will bring us one step closer to realizing an efficient photocatalyst for direct solar-to-fuel energy conversion.

We investigated the growth of IrO₂ as a co-catalyst, as it is known to be an efficient catalyst for water oxidation^7-11. A tunable structure of quantum dot (CdSe) embedded in a rod (cadmium sulfide)^12,13 was used as our photocatalyst substrate^14,15. It is currently undetermined whether the oxidative pathway occurs via a mediated pathway, or by a direct hole attack. Here, our knowledge and control over the photogenerated holes in the semiconductor heterostructure can be harnessed for a mechanistic study of oxidation reactions. This is made possible by the substrate architecture, which facilitates localization of confined holes^16,17 and formation of a distinct oxidation reaction site on the rod. The use of nanoscale materials with localized charge carrier can be exploited for mechanistic studies of redox reactions by simple examination of the products. In this way photodeposition can be used as a unique probe of both reduction and oxidation reaction pathways. This is one example of the new and exciting possibilities afforded by the combination of photodeposition and cutting edge colloidal synthesis^18-20.

The quest to develop an efficient photocatalyst for water splitting and renewable energy conversion has become an important thrust within the materials community. This has spurred worldwide interest in CdS, which is known to be highly active for hydrogen production, though it is hampered by photochemical instability. Our work here treats the Achilles heel of the material. IrO₂ decorated CdSe@CdS rods demonstrate remarkable photochemical stability under prolonged illumination in pure water.

Protocol

1. Synthesis of Quantum Dots²¹

1. Preparation of TOP:Se Precursor
   1. Combine 58 mg of Se powder with 0.360 g of Tri-n-octylphosphine (TOP) in a vial with a septum.
   2. Sonicate the TOP:Se mixture until it is clear with no solids.
2. Synthesis of CdSe
   1. Combine 3.0 g trioctylphosphine oxide (TOPO), 280 mg n-octadecylphosphonic acid (ODPA), and 60 mg CdO with a 3 mm x 8 mm cylindrical stir bar in a 25 ml 3-neck round bottom flask equipped with a thermocouple (inserted in a custom glass adapter), a reflux condenser with a T-joint (center neck), and a rubber septum. Assemble all glass-to-glass joints with high temperature vacuum grease. Connect the T-joint to a Schlenk line on one end that can be switched between a clean inert gas and vacuum, while connecting the other end to a bubbler.
      Caution: CdO is very toxic and should be weighed and added to the round bottom flask inside an enclosed environment such as a glovebox.
   2. Place the round bottom flask apparatus in a heating mantle, and purge with inert gas.
   3. Heat the solids in the round bottom flask to 150 °C, making sure to start stirring vigorously once the compounds melt (around 60-80 °C). In order to avoid overshooting the target temperature, heat to 100 °C and then 150 °C once the heating rate slows down or stabilizes.
   4. Degas the mixture under vacuum (at 150 °C) for at least 1 hr while still stirring. Make sure the T-joint is not open to the bubbler or the oil will get sucked into the flask and Schlenk line. When moving from gas to vacuum be careful to transition slowly to avoid more than a rolling boil.
   5. Refill the flask with inert gas (and continue to flow gas over the sample) and increase the temperature to 350 °C. The solution should turn clear as it heats up, and excess solids on the flask wall can be collected by careful swirling of the flask.
   6. Inject 1.5 g of TOP into the flask through the septum. Allow the solution temperature to stabilize before proceeding.
      Note: Try to minimize the amount of air/moisture injected by keeping the TOP in a septa vial under inert atmosphere, and injecting it as quickly as possible.
   7. Inject all of the TOP:Se mixture (prepared in section 1.1) into the flask through the septum, using a wide needle to inject the TOP:Se as quickly and uniformly as possible.
   8. Let the reaction proceed for the desired time, and remove from the heating mantle.
      1. For very small seeds remove from heat just before injecting. For larger seeds remove the flask from heat immediately after injecting TOP:Se or after waiting up to 3 min. Longer wait result in larger seeds.
   9. Let the reaction cool to approximately 100 °C and inject approximately 5 ml of degassed toluene. Transfer the solution to a vial under inert atmosphere for cleaning.
      Note: To simplify this process 10 ml of toluene can be placed in a 20 ml vial with a septa under constant flow of inert gas. Use approximately half of this toluene to inject into the cooling mixture, and then transfer the cooled mixture back into this vial.
   10. Cleaning of seeds
       1. Put the solution in a 50 ml centrifuge tube.
       2. Add methanol (approximately 5 ml) to precipitate out the seeds from the toluene mixture.
       3. Centrifuge at 3,400 x g for 5 min.
       4. Decant clear supernatant and re-dissolve the pellet in toluene (5-10 ml).
       5. Repeat steps 1.2.10.2 through 1.2.10.4 at least three times total.
   11. Dilute a small aliquot of the seeds in toluene in order to measure Ultraviolet-Visible (UV-Vis) absorbance between 350-800 nm. Use the peaks to determine the concentration and size of the CdSe seeds as described in the literature²².

2. Synthesis of Seeded Rods ²¹

1. Preparation of TOP:S Precursor
   1. Combine 1.2 g of S with 15 g of TOP in a vial with a stir bar.
   2. Stir until clear with no solids (usually at least 24 hr).
   3. Measure 0.62 g of this mixture into a vial with a septum.
2. Preparation of TOP:CdSe Precursor
   1. Measure the appropriate volume of CdSe seeds from step 1 (based on UV-Vis peak) into a vial with a septum.
      Note: For a calculated concentration of 5x10^-5 with 2.25 nm seeds (both values calculated from the UV-Vis spectra²²), use 300 µl of solution.
   2. Evaporate the toluene using a vacuum line until the seeds are dry. Do not leave under vacuum for more than 5-10 min once dry, as this can degrade the quality of the seeds.
   3. Re-dissolve all of the dried seeds in 0.5 g of TOP.
3. Synthesis of CdSe@Cds
   1. Combine 60 mg propylphosphonic acid (PPA), 3.35 g TOPO, 1.080 g ODPA, and 230 mg CdO with a 3 mm x 8 mm cylindrical stir bar in a 25 ml 3-neck round bottom flask equipped with a thermocouple (inserted in a custom glass adapter), a reflux condenser with a T-joint (center neck), and a rubber septum. Assemble all glass-to-glass joints with high temperature vacuum grease. Connect the T-joint to a Schlenk line on one end that can be switched between a clean inert gas and vacuum, while connecting the other end to a bubbler.
      Caution: CdO is very toxic and should be weighed and added to the round bottom inside an enclosed environment, such as a glovebox. PPA is regulated in some countries and can be replaced by butylphosphonic acid (BPA, 72 mg) or hexylphosphonic acid (HPA, 80 mg), though BPA and HPA usually result in shorter rods.
   2. Place the round bottom flask apparatus in a heating mantle, and purge with inert gas.
   3. Heat the solids in the round bottom flask to 120 °C, making sure to start stirring vigorously once the compounds melt (around 60-80 °C). In order to avoid overshooting the target temperature, heat to 90 °C and then 120 °C once the heating rate slows down or stabilizes.
   4. Degas the mixture under vacuum (at 120 °C) for at least ½ hr while still stirring.
      1. Make sure the T-joint is not open to the bubbler or the oil will get sucked into the flask and Schlenk line. When moving from gas to vacuum be careful to transition slowly to avoid more than a rolling boil. Use a cold trap with liquid nitrogen (LN₂) for a better vacuum.
   5. Refill the flask with inert gas (and continue to flow gas over the sample) and increase the temperature to 320 °C. The solution should turn clear as it heats up, and excess solids on the flask wall can be collected by careful swirling of the flask.
   6. Cool back down to 120 °C and degas under vacuum as in step 1.2.4.
   7. Refill and reheat the flask as in step 1.2.5.
   8. Inject 1.5 g of TOP into the flask through the septum. Allow the solution temperature to stabilize at 340 °C before proceeding.
      Note: Try to minimize the amount of air/moisture injected by keeping the TOP in a septa vial under inert atmosphere, and injecting it as quickly as possible.
   9. Inject the TOP:S mixture into the flask through the septum, using a wide needle to inject the TOP:S as quickly and uniformly as possible. Start a timer.
   10. Exactly 20 sec after injecting the TOP:S, inject the TOP:CdSe mixture into the flask through the septum, using a wide needle to inject the TOP:CdSe as quickly and uniformly as possible.
       Note: The temperature should have dropped to below 330 °C by this point due to the addition of RT TOP solutions.
   11. Set the temperature to 320 °C and let the reaction proceed for the desired time (8-15 min), and remove from the heating mantle.
   12. Let the reaction cool away from the heating mantle and inject approximately 5 ml of degassed toluene when the temperature reaches approximately 100 °C. Transfer the solution to a vial under inert atmosphere for cleaning.
       Note: To simplify this process 10 ml of toluene can be placed in a 20 ml vial with a septa under constant flow of inert gas. Use approximately half of this toluene to inject into the cooling mixture, and then transfer the cooled mixture back into this vial.
   13. Cleaning of rods
       1. Put the solution in a 50 ml centrifuge tube.
       2. Add methanol (approximately 5 ml) to precipitate out the seeds from the toluene mixture.
       3. Centrifuge at 3,400 x g for 5 min.
       4. Decant clear supernatant and re-dissolve the pellet in approximately 10 ml hexane.
       5. Add 1-2 ml each of n-octylamine and nonanoic acid to the solution. The solution should be transparent.
       6. Add 5 ml methanol and centrifuge for 5 min at 3,400 x g.
       7. Repeat steps 2.3.13.4 through 2.3.13.6 at least twice more.
       8. Re-dissolve pellet in 10 ml of toluene. If the pellet does not easily dissolve, more cleaning steps are likely needed, in which case repeat steps 2.3.13.4 through 2.3.13.6.
       9. Add approximately 7 ml of IPA, 1 ml at a time, until the solution is slightly cloudy even when mixed.
       10. Centrifuge for 30 min at 2,200 x g in order to separate longer rods from everything else.
       11. Re-dissolve pellet in 10-15 ml of toluene.
   14. Dilute a small aliquot of the seeds in toluene in order to measure UV-Vis absorbance and/or photoluminescence (PL) of the rods.
       Note: Any aliquot volume is acceptable as long as the dilution factor is known, however, a typical dilution factor would be 20. For PL, the absorption should be at or below 0.1 at the chosen excitation wavelength (typically use 450 nm). 

3. Transfer of Seeded Rods to Aqueous Solution

1. Preparation of Methanol Solution
   1. Pour approximately 10 ml of methanol into a centrifuge tube.
   2. Add approximately 250 mg mercaptoundecanoic acid (MUA) and 400 mg tetramethylammonium hydroxide (TMAH).
   3. Vortex or let sit until all solids fully dissolved.
2. Ligand Exchange
   1. Add methanol (5-10 ml, or enough to precipitate the rods) to ¼ to ½ of rods synthesized from step 2 in a centrifuge tube.
      Note: The volume of rods used will be dependent on the amount of toluene used to dissolve the rods for storage. If 10-15 ml are used as suggested in step 2.3.13.11, then 3-6 ml of the rod solution should be appropriate.
   2. Centrifuge at 3,400 x g for 5 min.
   3. Decant the clear supernatant.
   4. Add all of the methanol solution from section 3.1 to the pellet.
   5. Vortex or shake by hand to fully dissolve. Allow the solution to sit at least 1 hr to allow maximum ligand exchange to occur.
      Note: The solution should be allowed to sit for at least 1 hr even if it appears to dissolve immediately and completely
   6. Separate the solution into two halves in two centrifuge tubes.
      Note: Save the centrifuge tube used for step 3.1 and transfer half of the solution into there.
   7. Add 20 ml of toluene to each half. If there is a phase separation between the alcohol and toluene add methanol drop wise until the phases recombine.
   8. Centrifuge at 7,700 x g for 15 min.
   9. Very carefully decant the clear supernatant from pellet.
   10. Invert the centrifuge tube carefully in order to dry the sample.
   11. Add 5 ml ultrapure water to the pellet and store in a vial wrapped well in Al foil (or other opaque covering).
       Note: Once moved from toluene to water, the rods are not photostable, which is why they are covered. Even if kept in the dark the rods should be used as soon as possible, and it is not recommended to store rods in water for more than one month.

4. Growth of Iridium Nanocrystalline Particles

1. Sodium Hydroxide
   1. In a plastic vial weigh out 1,450 mg NaOH. Dissolve NaOH in 20 ml ultrapure water. Solution should be clear with no solids. 
2. Sodium Persulfate
   1. In a plastic vial weigh out 950 mg NaS₂O₈. Dissolve NaS₂O₈ in 20 ml ultrapure water. Solution should be clear with no solids.
3. Sodium Nitrate
   1. In a plastic vial weigh out 300 mg NaNO_3. Dissolve NaNO₃ in 18 ml ultrapure water. Solution should be clear with no solids.
4. Iridium Precursor Solution
   1. In a plastic vial weigh out 50 mg Na₃IrCl₆. Dissolve Na₃IrCl₆ in 5.0 ml ultrapure water. Solution should be transparent brown (like scotch) with no solids.
5. Preparation of sample
   1. Place a spectroscopic stirrer in a standard polystyrene cuvette.
      Note: Because the solution is very basic, quartz and other glass cuvettes should not be used.
   2. Add 0.20 ml iridium precursor solution from step 4.4.1.
   3. Add 0.50 ml nitrate solution from step 4.3.1.
   4. Add 0.30 ml of seeded rods in water from section 3 (trace toluene from the ligand exchange may cause clouding of the cuvette wall).
   5. Add 0.50 ml of persulfate solution from step 4.2.1.
   6. Add 0.50 ml of sodium hydroxide solution from step 4.1.1.
6. Illumination of sample
   1. Place the cuvette in a holder with stirring capabilities.
   2. Illuminate with 450 nm light at 100 mW for up to 4 hr. The solution should turn green and later blue.
7. Collecting sample
   1. Pour solution (but not stir bar) into a centrifuge tube.
   2. Centrifuge at 7,700 x g for 10 min.
   3. Carefully decant the supernatant from the pellet, which should be green or blue depending on the reaction time selected.
      Note: The pellet can now be collected or dispersed in a polar solvent through sonication for use in other experiments.

Results

Transmission electron micrographs (TEM) were collected in order to see the distribution of iridium oxide on the seeded rods (Figure 1). TEM samples were prepared by pipetting a drop of dissolved particles onto a TEM grid. X-ray diffraction (XRD, Figure 2) and X-ray photoelectron spectra (XPS, Figure 3) were used to characterize the observed growth as a mix of crystalline IrO₂ and Ir₂O₃. Preparation of XRD ...

Discussion

The synthesis of CdSe seeds and CdSe@CdS seeded rods has been well studied^21,24,25. Slight modifications to the amounts, temperatures, and times for steps of the synthesis of these substrate particles can be used to tune their length, diameter, and/or morphology. The synthetic protocol described herein yields highly photoluminescent seeded-rods of uniform dimensions.

The ligand exchange procedure allows for the use of seeded rods in polar environments, in this case water. At the fin...

Materials

Name	Company	Catalog Number	Comments
Sulfur (S)	Sigma	84683
Selenium (Se)	Sigma	229865
Cadmium Oxide (CdO)	Sigma	202894	Highly Toxic
n-Octadecylphosphonic acid (ODPA)	Sigma	715166
Propylphosphonic acid (PPA)	Sigma	305685	Highly regulated in some countries and regions
Butylphosphonic acid (BPA)	Sigma	737933	Alternative to PPA
Hexylphosphonic acid (HPA)	Sigma	750034	Alternative to PPA
Trioctylphosphonic oxide (TOPO)	Sigma	346187
Tri-n-octylphosphine, 97% (TOP)	Sigma	718165	Air sensitive
Spectrochemical Stirbar	Sigma	Z363545
Sodium Hydroxide	Sigma	S5881
Methanol	Sigma	322415
Toluene	Sigma	244511
Hexane	Sigma	296090
Octylamine	Sigma	74988
Nonanoic Acid	Sigma	N5502
Isopropanol	Sigma	278475
Mercaptoundecanoic Acid (MUA)	Sigma	674427
Tetramethylammonium Hydroxide (TMAH)	Sigma	T7505
Apiezon H Grease (high temperature grease)	Sigma	Z273562
Sodium Persulfate	Sigma	216232
Sodium Nitrate	Sigma	229938
Sodium Hexachloroiridate(III) hydrate	Sigma	288160
Mounted 455 nm LED	Thorlabs	M455L3
Cuvette Holder	Thorlabs	CVH100
25 ml 3-neck Round Bottom Flask	Chemglass	CG-1524-A-02
Liebig Condensor	Chemglass	CG-1218-A-20
T-Joint Adapter	Chemglass	AF-0509-10