Toluidine Blue Staining of Resin-Embedded Sections for Evaluation of Peripheral Nerve Morphology

Summary

Here we present a protocol to visualize fine structures of peripheral nerves by obtaining and staining 1-2 µm sections with toluidine blue

Abstract

Peripheral nerves extend throughout the body, innervating target tissues with motor or sensory axons. Due to widespread distribution, peripheral nerves are frequently damaged because of trauma or disease. As methods and strategies have been developed to assess peripheral nerve injury in animal models, function and regeneration, analyzing the morphometry of the peripheral nerve has become an essential terminal outcome measurement. Toluidine blue staining of nerve cross sections obtained from resin embedded nerve sections is a reproducible method for qualitative and quantitative assessments of peripheral nerves, enabling visualization of morphology number of axons and degree of myelination. This technique, as with many other histological methods, can be difficult to learn and master using standard written protocols. The intent of this publication is therefore to accentuate written protocols for toluidine blue staining of peripheral nerves with videography of the method, using sciatic nerves harvested from rats. In this protocol, we describe in vivo peripheral nerve fixation and collection of the tissue, and post-fixation with 2% osmium tetroxide, embedding of nerves in epoxy resin, and ultramicrotome sectioning of nerves to 1-2μm thickness. Nerve sections then transferred to a glass slide and stained with toluidine blue, after which they are quantitatively and qualitatively assessed. Examples of the most common problems are shown, as well as steps for mitigating these issues.

Introduction

Peripheral nerves extend throughout the body, innervating target tissues with motor or sensory axons¹. Peripheral nerve defects caused by medical disorders and trauma represent a major public health concern and have large economic impacts^2,3. Despite the advances in assessing the outcomes of peripheral nerve injuries and understanding nerve regeneration, traditional methods such as nerve histology and staining techniques are essential tools to qualitatively and quantitatively assess nerve health as a terminal outcome measurement in animal models or excised human tissue. This is often paired with electrophysiological measurements of peripheral nerve function, where morphometry can reveal why functional nerve regeneration did or did not occur.

Toluidine blue staining of resin embedded semi-thin peripheral nerve sections is a specialized method for imaging myelinated nerve fibers, providing high quality and clear detailed images of nerve structures^4,5,6. Toluidine blue is an acidophilic metachromatic stain, discovered by William Henry Perkin in 1856⁷, and has been used in several medical applications⁸. Toluidine blue-stained peripheral nerve sections obtained from resin-embedded nerve segments allows for clear visualization of nerve structures. Visualization of myelin sheath structure can be enhanced by the use of osmium tetroxide post-fixation^4,9. Osmium tetroxide is a toxic oxidant and lipid fixative agent that interacts with the double bonds in lipids, resulting in starkly defined lipid-rich myelin sheaths¹⁰. However, osmium tetroxide is toxic, expensive, requires a longer incubation of nerve segments, and is not always used.

Alternative methods of processing and staining have been developed for visualization of peripheral nerve morphology; Paraffin, cryogenic sectioning, and epoxy resin-embedded nerve sectioning followed by staining with toluidine blue or phenylenediamine solution has been used to quantify morphological changes of peripheral nerve regeneration ^11,12. These methods each have their advantages and yield essential data on the number of axons, myelin thickness, axon diameter, and axon diameter to myelinated fiber diameter (g-ratio) ^11,13,14,15.

The primary distinction of the resin-embedding in this protocol is that it facilitates obtaining 1-2 μm thickness cross-sections due to the hardness of the resin while maintaining the histological qualities of the nerve. These thin sections, as opposed to the 4-5 μm thickness sections obtained from paraffin embedding, provide peripheral nerve sections with higher resolution, allowing for a more accurate quantification of axon myelination, such as the g-ratio, that cannot be obtained from thicker sections¹⁶. While cryogenic sectioning can be used to obtain 1-2 µm sections, it has been our experience that it is more difficult to obtain sections without numerous large cracks. Such cracked sections can cause inaccurate counting of the number of axons and aspects of myelination.

In addition to toluidine blue staining¹⁷, a silver staining method¹⁸ and Masson's trichrome staining⁴ can also be used to show nerve axons. However, using resin embedding of rat median nerve sections stained with either hematoxylin and eosin or Masson's trichrome showed faint myelin sheaths and unrecognized structures, whereas toluidine blue staining showed clear myelin sheath image and easily can be quantified⁴. Despite some limitations, toluidine blue staining of resin embedded peripheral nerves is a valuable technique that can be used when high resolution images of nerve morphology are required.

The primary disadvantage for resin embedding is that it is time-consuming and does not allow for immunostaining of the same tissue due to the difficulty of antigen retrieval when compared to paraffin and frozen embedded sections techniques. Thus, it is not generally possible to utilize the same tissue for immunostaining that is processed via resin-embedding for toluidine blue staining. Although not used here, if immunohistochemistry is desired in resin embedded sections, the use of glycol methacrylate embedding resins allows for immunohistochemistry to be performed on tissue sections, but it is relatively expensive¹⁹. This can be somewhat mitigated by cutting the peripheral nerve into separate segments, some for resin-embedding and others for immunostaining directly after fixation.

The process of toluidine blue staining of resin embedded peripheral nerves, as with most histopathological analysis, can be broken up into five stages, including fixation, dehydration, embedding, sectioning, and staining²⁰. We aim here to provide a protocol and practical guideline for using resin embedded rat sciatic nerve sections stained with toluidine blue to acquire high quality images.

Protocol

Adult Sprague Dawley rats were used in this project and all procedures were approved by the University of Wyoming Institutional Animal Care and Use Committee.

1. Surgery and In Vivo Nerve Fixation

NOTE: Vendor information for all materials and equipment used in this protocol are listed in the Table of Materials.

NOTE: In vivo nerve fixation is used to preserve the tissue and reduce structural degradation that can occur between the time of death and collection of the nerves. In vivo tissue fixation is a standard practice for preparation of nervous system tissue for histology, where perfusion is often a precursor to this. The placement and size of peripheral nerves allowed for in situ fixation. We do not recommend collection and fixation of tissue after euthanasia due to the possibility of tissue degradation.

1. Prepare the rat for general anesthesia by placing it in an induction chamber with 2-3% isoflurane, then place the anesthetized rat in the prone position on the top of a dissection mat and maintain at 1-2% of isoflurane via anesthetic nose cone. To ensure adequate depth of anesthesia, test animals for pedal withdrawal at the hind feet and check for the absence of palpebral reflexes at the eyes by touching the medial canthus of the eye.
   NOTE: Intraperitoneal injection of ketamine is a commonly used alternative to inhaled isoflurane.
2. To expose the sciatic nerve, shave the hair of the hind limb(s) and clean the shaved areas with 70% ethanol. With a scalpel or scissors, make a 2-3 cm incision in the skin along the hind limb from the knee up to the greater trochanter, where palpation of the femur using the sterile scalpel to ensure the proper location of the incision. The femur is located just proximal to the most accessible segment of the sciatic nerve. Even though this is a non-survival surgery, maintain sterile techniques.
3. After making the skin incision, locate the plane between the biceps femoris muscle and the gluteus maximus muscle, and using microdissection scissors separate the underlying fascia and expose 2-3 cm of the underline sciatic nerve. To expose a clear section of the sciatic nerve, use a retractor to widen the gap between the two muscles (Figure 1A). With fine forceps and iris scissors, carefully separate the nerve from surrounding connective tissue, taking great care not to compress or cut the nerve.
4. Add sufficient Trump’s fixative (4% formaldehyde, 1% glutaraldehyde in 1x PBS (phosphate buffered saline) with 1.16 g of NaH2PO4·H2O per 100 mL) into the cavity containing the exposed nerve to cover the nerve and let sit for 10 min. If necessary, place gauze under the hind leg to improve the angle so that more fixative can be added into the cavity. Remove the fixative after 10 min and repeat this step two more times.
5. Using a dissecting microscope, cut the nerve from both sides using fine dissection scissors, making sure not to stretch or pinch the sciatic nerve, and immediately put the nerve sections in 15 mL tubes containing Trump's fixative at 4 °C for one week, changing the fixative every 48 h.
6. Do not leave animals unattended during any part of the surgical procedure. After removal of the nerve, euthanize animals by cervical dislocation while under anesthesia.

2. Osmium Tetroxide Treatment and Resin Embedding

1. Post fixation, carefully remove any remaining fat and connective tissues from the nerve and use a sharp scalpel to cut the nerve into segments approximately 5 mm in length (nerve segments can be separated and labeled in different tubes). Prepare fresh 2% osmium tetroxide diluted in Trump's fixative solution and keep in a glass tube. Immerse nerve segments in 2% osmium tetroxide for 2 h, which can be in plastic tubes for this short period of time.
   NOTE: Some plastic tubes react with osmium tetroxide, causing a darkening of the solution, so prolonged storage of osmium tetroxide in plastic tubes is not recommended.
2. Using an epoxy embedding medium kit, prepare the final embedding formula:
   1. Mix the epoxy embedding medium with DDSA solution (dodecenylsuccinic anhydride; mixture A) and mix the epoxy embedding medium with NMA solution (methylnadic anhydride; mixture B). Let both mixtures A and B mix at least 20 min by stirring with a magnetic stirrer.
   2. Immediately before use, mix mixture A and B and add the accelerator DPM-30 (2,4,6-tris(dimethylaminomethyl)phenol) in the proportion of 1.5 to 2.0% of the total volume of the mixture. Note that the DPM-30 solution should be measured precisely to prevent the block from becoming dark in color and brittle. All resin chemicals are toxic; take extra care to prevent skin contact or inhalation.
3. Using 1.5 mL tubes, wash nerve segments with PBS and start the dehydration process by placing the nerve segments in different acetone/distilled water passages: 30%, 60%, 90%, concentrations for 10 min each, then in 100% acetone 3 times for 10 min each.  Note that ethanol can be used in the place of acetone.
4. For resin infiltration, place the nerve segments in a mixture of 1 part of the final embedding mixture and 1 part 100% acetone for 30 min, then in a mixture of 2 parts of the final embedding mixture and 1 part 100% acetone for 30 min, and finally place the nerve segments in the final embedding mixture for 30 min.
5. Put the nerve segments into silicone rubber embedding molds (we have used 106 mm length x 71 mm width x 7 mm depth; block size 11 mm length x 6 mm width x 3 mm depth). Gently add the resin on top of the nerves, making sure to cover the whole nerve segments and avoid making air bubbles. Leave the mold containing nerve segments with the resin to polymerize at 60 °C overnight.

3. Sectioning by Ultramicrotome

1. Prepare glass knives using a glass knife maker (Figure 1B) and make glass knives with boats(Figure 1C), which are used to collect nerve sections floating on the distilled water.
2. Place resin embedded nerve blocks into the ultramicrotome holder with the trapezoidal side facing up. Using the ultramicrotome scope, trim any excess resin surrounding the nerve tissue, and make the block face a trapezoid shape and as close to the longitudinal surface of the nerve as possible using a single-edged blade, such as a razor blade. Do not penetrate the longitudinal surface of the nerve segment, which is recognizable by its dark staining by osmium tetroxide.
   NOTE: Trimming of excess resin will reduce the area of resin to be sectioned and improve blade performance and cutting in subsequent steps.
3. Using the ultramicrotome, make multiple cross sections sufficient to expose a uniform cross section surface of the nerve tissue using a plain glass knife. Once this is done, switch to a glass knife whose boat is filled with distilled water at room temperature and adjust the ultramicrotome to 1-2 μm to cut thin sections.
4. Transfer floating thin sections from the glass knife boat to a drop of deionized water on glass slide using metal loop (Figure 1D). Dry slides containing sections by passing several times over a flame for a few seconds, making sure not to overheat the sections. Stain dried sections immediately with toluidine blue or store at room temperature for several days before staining.
   NOTE: Sections can also be dried using a plate warmer at 60 °C for 15 min. A slow drying process makes the sections smooth.

4. Toluidine Blue Staining

1. Prepare 1% solution of toluidine blue by dissolving 2 g of sodium borate in 100 mL of deionized water, then add 1 g of toluidine blue and stir until dissolved. Filter the solution using filter paper (pore size: 11 µm) and keep the solution in an opaque bottle at room temperature for up to two weeks.
2. Using a plastic pipette or micro pipettor, add a drop of toluidine blue solution on the top of the nerve sections and leave for 20-30 s.
3. Rinse off all toluidine blue solution excess by gently dipping the slides into deionized water jar and repeat 3-4 times until sections are clear. Dry the slides at least 15 min at 60 °C or overnight at room temperature and then cover the sections with a coverslip using regular mounting medium. Examine the mounted slides immediately or store at room temperature.
4. Examine under a light microscope. A 100X oil immersion lens is recommended for detailed images used to calculate g-ratios.

Results

Resin embedded peripheral nerve sections stained with toluidine blue allow for accurate histological data quantifications. An overview of the procedure is shown in (Figure 2). Sciatic nerves sections embedded in resin medium and stained with toluidine blue showed clear images with optimal resolution (Figures 3). Nerve damage can cause many changes in nerve morphological structures, for example, changes in nerve fiber, axon diameter, and myeli...

Discussion

Examinations of the morphological structures of peripheral nerve injury and regeneration are frequent subjects of study¹³. In this protocol, we describe the steps to obtain high quality images for histological data quantifications using rat sciatic nerve tissue embedded in resin blocks and stained with toluidine blue. This technique provides an image of nerve morphology in which the nerve regeneration can be quantified by measuring the number of axons, degree of myelination, presence of infiltrati...

Materials

Name	Company	Catalog Number	Comments
Dulbecco's Phosphate Buffer Saline	Gibco	14200-075
Glutaraldehyde Solution	Sigma-Aldrich	G6257
Paraformaldehyde	Sigma-Aldrich	P6148
Sodium Phosphate Monobasic Monohydrate	Sigma-Aldrich	S9638
Toluidine Blue O	Sigma-Aldrich	T3260
Sodium Tetraborate Decahydrate	Acros Organics	205950010
Isoflurane	Piramal	NDC 66794-013-25
Epoxy Embedding Medium Kit	Sigma-Aldrich	45359
Sodium Hydroxide Solution	Sigma-Aldrich	72068	To adjust Trump's fixative pH
Acetone	Fisher Chemical	170942
Osmium Tetroxide Solution	Sigma-Aldrich	75632
VWR Micro Slides, Superfrost Plus	VWR	48311-703
Microscope Cover Glass	Fisher Scientific	12545102
Pelco Embedding Cast	Fisher Scientific	NC9671811
Glass Knife Maker	RMC Products	GKM-2
Ultramicrotome	RMC Products	MT-XL
15 mL Conical Tube	Falcon	ISO 9001
Eppendorf 1.5 mL microcentrifuge tubes	Sigma-Aldrich	T9661
4 mL Glass Vial	Sigma-Aldrich	854190
Razor Blades	VWR	55411-050	For trimming resin block
Perfect Loop	Electron Microscopy Sciences	70944	For picking up thin resin sections
Ultra Glass Knife Strips 6.4 mm x 25 mm x 400 mm	Electron Microscopy Sciences	71012
100 Watt Oven	Millipore	6350115
Whatman Filter Paper	Sigma-Aldrich	WHA10010155
3 mL plastic pipette	Sigma-Aldrich	Z331740
Micro-surgical Kit	World precision instruments
Olympus fluorescence microscope			Dual CCD Color and Monochrome Camera, DP80