Name: a microfluidic model of biomimetically breathing pulmonary acinar airways
Uploaded: 2016-05-09T13:00:00.000+00:00
Duration: 9 min 39 s
Description: Watch this Scientific Journal Video about A Microfluidic Model of Biomimetically Breathing Pulmonary Acinar Airways at JoVE.com

This work was supported in part by the European Commission (FP7 Program) through a Career Integration Grant (PCIG09-GA-2011-293604), the Israel Science Foundation (Grant nr. 990/12) and the Technion Center of Excellence in Environmental Health and Exposure Science (TCEEH). Microfabrication of microfluidic chips was conducted at the Micro-Nano Fabrication Unit (MNFU) of the Technion and supported by a seed grant from the Russel Berrie Institute of Nanotechnology (RBNI) at Technion. The authors thank Avshalom Shai for assistance during deep reactive ion etching (DRIE) and Molly Mulligan and Philipp Hofemeier for helpful discussions.

1. Master Fabrication
<ol>
	<li>Use deep reactive ion etching (DRIE) of a silicon on insulator (SOI) wafer to fabricate a master silicon wafer as described in former works32, 33. 
	NOTE: DRIE is preferred to standard SU-8 micromachining due to the high aspect ratio features (40 &#181;m wide and 90 &#181;m deep trenches).</li>
</ol>
2. Casting and Sealing of the Microfluidic Device
<ol>
	<li>Mix PDMS and curing agent at a 10:1 weight ratio inside a clean small container such as a plastic weighing dish.</li>
	<li>Degas the mixture in a desiccator under vacuum until all air bubbles are removed. 
	NOTE: Prepare enough PDMS for all subsequent steps. Here below, the acronym &#34;PDMS&#34; refers always to the degassed 10:1 PDMS:curing-agent mixture that was prepared in steps 2.1 and 2.2.</li>
	<li>Pour the degassed-mixture to a height of approximately 1 mm above the master wafer. Degas once again for at least 40 min to remove all the air bubbles above the wafer and minimize the bubbles below the wafer. 
	NOTE: Make sure that the wafer is as close as possible to the bottom of the plate. If necessary press the wafer gently to the bottom using 2 stirring sticks and degas once again.</li>
	<li>Bake at 65 &#176;C for 20 min in a natural convection oven. 
	NOTE: After 20 min the PDMS is hardened and almost fully cured. While a longer baking time is possible baking for 20 min saves time and improves the adherence of the second PDMS layer (see below) to the first one.</li>
	<li>File the barrel section of a plastic 2 ml syringe using a fine grit sand paper to improve adherence to PDMS. In addition, use the sand paper to flatten the base of the syringe barrel by placing the sand paper on a flat surface and sliding the base of the syringe barrel on top of it. Clean the syringe using pressurized air.</li>
	<li>Place the barrel section of the syringe on top of the first PDMS layer with the large opening facing the surface of the PDMS, and pour a second layer of PDMS on top of the first one to a height of ~5 mm, and degas the PDMS once again in a desiccator. 
	NOTE: The second PDMS layer should be poured from the small container around the barrel, and should not enter within it.&#160;</li>
	<li>Bake the entire setup at 65&#176; C for at least 2 hr in a natural convection oven. 
	NOTE: There is no need to hold the barrel in place during the curing processes since the weight of the PDMS pressing against the wide base of the barrel holds the barrel firmly in place.</li>
	<li>Cut through the PDMS mold around the patterned region of the master wafer using a scalpel. While cutting, the scalpel should weakly touch the surface of the wafer. Then, gently insert a thin tool such as wafer forceps in the notch created by the scalpel, and peel off the PDMS cast from the master wafer.</li>
	<li>Place the cast on a soft surface covered with aluminum foil with the patterned side facing up (i.e., the barrel should hang from the edge of the table), and punch a hole in the PDMS at the chamber inlet and channel inlet using a 1 mm biopsy punch.&#160;</li>
	<li>Coat a clean glass slide with a (degassed) 10:1 PDMS:curing-agent mixture using a spin coater programmed at 3,000 rpm for 30 sec, and bake for &#62;1 hr at 65 &#176;C. Then, clean the slide and PDMS cast using clear tape.</li>
	<li>Treat the surface of the PDMS mold and PDMS coated glass slide with O2 plasma (e.g., using a hand-held corona treater) for 1 min, and then gently press the surfaces together and bake at 65 &#176;C overnight (O/N).</li>
</ol>
3. Device Filling and Actuation
<ol>
	<li>Mix water suspended fluorescent polystyrene particles with water and glycerol in a glass vial to obtain a 64/36 (v/v) glycerol/water mixture with 0.25% (w/w) particles..</li>
	<li>Place a drop of the glycerol solution on top of the channel inlet and a drop of DI water on the chamber inlet, then place the apparatus inside a desiccator and vacuum for ~5 min. 
	NOTE: Before releasing the vacuum wait for the bubbles that form in the drops of glycerol solution and DI water to pop. Upon vacuum release the liquids are sucked into the voids inside the device. If residual air remains inside the channels, eliminate it by applying external pressure on the fluids (e.g., using a syringe) and allowing the air to diffuse into the PDMS.</li>
	<li>Inject ~2 ml of DI water into the top chamber (i.e., the syringe barrel, Fig. 2b) until it is fully filled with water. Then cover the top chamber with a 19 gauge blunt syringe tip, cut the tip of another blunt 19 gauge syringe tip and insert this tip to the side chamber inlet. Connect both syringe tips to a 1 ml syringe via thin Teflon tubing and a T-shaped connector. 
	NOTE: Make sure that the 1 ml syringe, Teflon tubing, T-shaped connector and top chamber (2 ml syringe barrel) are all filled with water without bubbles. This may be achieved by opening connection points, pushing water through empty sections of tubing and reconnecting the connection points.</li>
	<li>Connect the 1 ml syringe to a syringe pump pre-programmed to mimic for example a quiet tidal breathing cycle (with a period of T&#160;= 4 sec) constructed of linear ramps, i.e., from zero to 1.8 ml/min in 1 sec, from 1.8 ml/min&#160;to -1.8 ml/min in 2 sec and from -1.8 ml/min back to zero in 1 sec.</li>
</ol>
4. Flow Visualization Experiments: Micro-particle Image Velocimetry (&#181;PIV)
<ol>
	<li>While the device is being actuated, obtain a series of 9 - 12 phase-locked, double-frame images of the particle-seeded flow using a micro-particle image velocimetry (&#181;PIV) system consisting for example of a dual frame-multiple exposure CCD camera (e.g., 1,600 &#215; 1,200 pixels to achieve sufficient resolution), a double pulsed Nd-YAG laser (wavelength: 532 nm, output energy: 400 mJ, pulse duration: 4 nsec), and an inverted microscope. 
	NOTE: Such a system is capable of obtaining frame pairs with a time lag of down to a few microseconds between the first and second frames. To achieve phase-locked double frame images, it is useful to acquire a double frame series at e.g., 10 Hz (frame pairs are separated by 0.1 sec from one another). Then, the data may be reorganized so that all frame pairs that are separated by a full cycle time (here T =&#160;4 sec) form a new time series. Image acquisition should be repeated several times while modifying the lag time between the first and second frames in each frame pair (i.e., 100&#160;&#181;sec to 0.1&#160;sec) for resolving different flow regions inside the alveolar cavity. 
	Note: alternative setups with regards to best combinations of image acquisition systems (i.e., camera) and illumination sources (i.e., lasers) to image such microflows are also available34, 35.</li>
	<li>Use a sum-of-correlation algorithm to compute phase-locked velocity vector maps of the resulting flow field from the image series for each time lag used. Repeat this process several times with varying lag times between the first and second frames in each frame pair for resolving different flow regions inside the alveolar cavity. Next, use a data analysis program to stitch together the individual flow maps into a complete and high-detailed map of flow patterns by averaging overlapping data points33.</li>
</ol>

<ol>
	<li>Kleinstreuer, C., Zhang, Z. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Airflow+and+Particle+Transport+in+the+Human+Respiratory+System.">Airflow and Particle Transport in the Human Respiratory System.</a> Annu. Rev. Fluid Mech. 42 (1), 301-334 (2010).</li><li>Sznitman, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Respiratory+microflows+in+the+pulmonary+acinus.">Respiratory microflows in the pulmonary acinus.</a> J. Biomech. 46 (2), 284-298 (2013).</li><li>Tsuda, A., Henry, F. S., Butler, J. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Gas+and+aerosol+mixing+in+the+acinus.">Gas and aerosol mixing in the acinus.</a> Respir. Physiol. Neurobiol. 163 (1-3), 139-149 (2008).</li><li>Kleinstreuer, C., Zhang, Z., Donohue, J. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Targeted+Drug-Aerosol+Delivery+in+the+Human+Respiratory+System.">Targeted Drug-Aerosol Delivery in the Human Respiratory System.</a> Annu. Rev. Biomed. Eng. 10 (1), 195-220 (2008).</li><li>Semmler-Behnke, M., Kreyling, W. G., Schulz, H., Takenaka, S., Butler, J. P., Henry, F. S., Tsuda, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nanoparticle+delivery+in+infant+lungs.">Nanoparticle delivery in infant lungs.</a> Proc. Natl. Acad. Sci. 109 (13), 5092-5097 (2012).</li><li>Sznitman, J., Heimsch, F., Heimsch, T., Rusch, D., Rosgen, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Three-Dimensional+Convective+Alveolar+Flow+Induced+by+Rhythmic+Breathing+Motion+of+the+Pulmonary+Acinus.">Three-Dimensional Convective Alveolar Flow Induced by Rhythmic Breathing Motion of the Pulmonary Acinus.</a> J. Biomech. Eng. 129 (5), 658-665 (2007).</li><li>Tsuda, A., Henry, F. S., Butler, J. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Chaotic+mixing+of+alveolated+duct+flow+in+rhythmically+expanding+pulmonary+acinus.">Chaotic mixing of alveolated duct flow in rhythmically expanding pulmonary acinus.</a> J. Appl. Physiol. 79 (3), 1055-1063 (1995).</li><li>Henry, F. S., Butler, J. P., Tsuda, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Kinematically+irreversible+acinar+flow:+a+departure+from+classical+dispersive+aerosol+transport+theories.">Kinematically irreversible acinar flow: a departure from classical dispersive aerosol transport theories.</a> J. Appl. Physiol. 92 (2), 835-845 (2002).</li><li>Kumar, H., Tawhai, M. H., Hoffman, E. A., Lin, C. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+effects+of+geometry+on+airflow+in+the+acinar+region+of+the+human+lung.">The effects of geometry on airflow in the acinar region of the human lung.</a> J. Biomech. 42 (11), 1635-1642 (2009).</li><li>Lee, D. Y., Lee, J. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Characteristics+of+particle+transport+in+an+expanding+or+contracting+alveolated+tube.">Characteristics of particle transport in an expanding or contracting alveolated tube.</a> J. Aerosol Sci. 34 (9), 1193-1215 (2003).</li><li>Tsuda, A., Butler, J. P., Fredberg, J. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effects+of+alveolated+duct+structure+on+aerosol+kinetics.+I.+Diffusional+deposition+in+the+absence+of+gravity.">Effects of alveolated duct structure on aerosol kinetics. I. Diffusional deposition in the absence of gravity.</a> J. Appl. Physiol. 76 (6), 2497-2509 (1994).</li><li>Tsuda, A., Butler, J. P., Fredberg, J. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effects+of+alveolated+duct+structure+on+aerosol+kinetics.+II.+Gravitational+sedimentation+and+inertial+impaction.">Effects of alveolated duct structure on aerosol kinetics. II. Gravitational sedimentation and inertial impaction.</a> J. Appl. Physiol. 76 (76), 2510-2516 (1994).</li><li>Ma, B., Darquenne, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Aerosol+bolus+dispersion+in+acinar+airways&#8212;influence+of+gravity+and+airway+asymmetry.">Aerosol bolus dispersion in acinar airways&#8212;influence of gravity and airway asymmetry.</a> J. Appl. Physiol. 113 (3), 442-450 (2012).</li><li>Ma, B., Darquenne, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Aerosol+deposition+characteristics+in+distal+acinar+airways+under+cyclic+breathing+conditions.">Aerosol deposition characteristics in distal acinar airways under cyclic breathing conditions.</a> J. Appl. Physiol. 110 (5), 1271-1282 (2011).</li><li>Heimsch, J., Sznitman, T., Wildhaber, J. H., Tsuda, A., R&#246;sgen, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Respiratory+Flow+Phenomena+and+Gravitational+Deposition+in+a+Three-Dimensional+Space-Filling+Model+of+the+Pulmonary+Acinar+Tree.">Respiratory Flow Phenomena and Gravitational Deposition in a Three-Dimensional Space-Filling Model of the Pulmonary Acinar Tree.</a> J. Biomech. Eng. 131 (3), 031010 (2009).</li><li>Litzlbauer, H. D., Korbel, K., Kline, T. L., Jorgensen, S. M., Eaker, D. R., Bohle, R. M., Ritman, E. L., Langheinrich, A. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Synchrotron-Based+Micro-CT+Imaging+of+the+Human+Lung+Acinus.">Synchrotron-Based Micro-CT Imaging of the Human Lung Acinus.</a> Anat. Rec. Adv. Integr. Anat. Evol. Biol. 293 (9), 1607-1614 (2010).</li><li>Tsuda, A., Filipovic, N., Haberth&#252;r, D., Dickie, R., Matsui, Y., Stampanoni, M., Schittny, J. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Finite+element+3D+reconstruction+of+the+pulmonary+acinus+imaged+by+synchrotron+X-ray+tomography.">Finite element 3D reconstruction of the pulmonary acinus imaged by synchrotron X-ray tomography.</a> J. Appl. Physiol. 105 (3), 964-976 (2008).</li><li>Berg, E. J., Weisman, J. L., Oldham, M. J., Robinson, R. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Flow+field+analysis+in+a+compliant+acinus+replica+model+using+particle+image+velocimetry+(PIV).">Flow field analysis in a compliant acinus replica model using particle image velocimetry (PIV).</a> J. Biomech. 43 (6), 1039-1047 (2010).</li><li>Sznitman, J., Sutter, R., Altorfer, D., Stampanoni, M., R&#246;sgen, T., Schittny, J. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Visualization+of+respiratory+flows+from+3D+reconstructed+alveolar+airspaces+using+X-ray+tomographic+microscopy.">Visualization of respiratory flows from 3D reconstructed alveolar airspaces using X-ray tomographic microscopy.</a> J. Vis. 13 (4), 337-345 (2010).</li><li>Henry, F. S., Haber, S., Haberth&#252;r, D., Filipovic, N., Milasinovic, D., Schittny, J. C., Tsuda, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+Simultaneous+Role+of+an+Alveolus+as+Flow+Mixer+and+Flow+Feeder+for+the+Deposition+of+Inhaled+Submicron+Particles.">The Simultaneous Role of an Alveolus as Flow Mixer and Flow Feeder for the Deposition of Inhaled Submicron Particles.</a> J. Biomech. Eng. 134 (12), 121001 (2012).</li><li>Chhabra, S., Prasad, A. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Flow+and+Particle+Dispersion+in+Lung+Acini:+Effect+of+Geometric+and+Dynamic+Parameters+During+Synchronous+Ventilation.">Flow and Particle Dispersion in Lung Acini: Effect of Geometric and Dynamic Parameters During Synchronous Ventilation.</a> J. Fluids Eng. 133 (7), 071001 (2011).</li><li>Cinkotai, F. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fluid+flow+in+a+model+alveolar+sac.">Fluid flow in a model alveolar sac.</a> J. Appl. Physiol. 37 (2), 249-251 (1974).</li><li>Karl, A., Henry, F. S., Tsuda, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Low+reynolds+number+viscous+flow+in+an+alveolated+duct.">Low reynolds number viscous flow in an alveolated duct.</a> J. Biomech. Eng. 126 (4), 420-429 (2004).</li><li>Tippe, A., Tsuda, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=recirculating+flow+in+an+expanding+alveolar+model:+experimental+evidence+of+flow-induced+mixing+of+aerosols+in+the+pulmonary+acinus.">recirculating flow in an expanding alveolar model: experimental evidence of flow-induced mixing of aerosols in the pulmonary acinus.</a> J. Aerosol Sci. 31 (8), 979-986 (2000).</li><li>Berg, E. J., Robinson, R. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Stereoscopic+particle+image+velocimetry+analysis+of+healthy+and+emphysemic+alveolar+sac+models.">Stereoscopic particle image velocimetry analysis of healthy and emphysemic alveolar sac models.</a> J. Biomech. Eng. 133 (6), 061004 (2011).</li><li>Ma, B., Ruwet, V., Corieri, P., Theunissen, R., Riethmuller, M., Darquenne, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=CFD+simulation+and+experimental+validation+of+fluid+flow+and+particle+transport+in+a+model+of+alveolated+airways.">CFD simulation and experimental validation of fluid flow and particle transport in a model of alveolated airways.</a> J. Aerosol Sci. 40 (5), 403-414 (2009).</li><li>Kumar Mahto, S., Tenenbaum-Katan, J., Sznitman, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Respiratory+Physiology+on+a+Chip.">Respiratory Physiology on a Chip.</a> Scientifica. 2012, e364054 (2012).</li><li>Huh, D., Fujioka, H., Tung, Y. C., Futai, N., Paine, R., Grotberg, J. B., Takayama, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acoustically+detectable+cellular-level+lung+injury+induced+by+fluid+mechanical+stresses+in+microfluidic+airway+systems.">Acoustically detectable cellular-level lung injury induced by fluid mechanical stresses in microfluidic airway systems.</a> Proc. Natl. Acad. Sci. 104 (48), 18886-18891 (2007).</li><li>Song, Y., Baudoin, M., Manneville, P., Baroud, C. N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+air&#8211;liquid+flow+in+a+microfluidic+airway+tree.">The air&#8211;liquid flow in a microfluidic airway tree.</a> Med. Eng. Phys. 33 (7), 849-856 (2011).</li><li>Tavana, H., Huh, D., Grotberg, J. B., Takayama, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidics,+Lung+Surfactant,+and+Respiratory+Disorders.">Microfluidics, Lung Surfactant, and Respiratory Disorders.</a> Lab Med. 40 (4), 203-209 (2009).</li><li>Huh, D., Matthews, B. D., Mammoto, A., Montoya-Zavala, M., Hsin, H. Y., Ingber, D. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Reconstituting+Organ-Level+Lung+Functions+on+a+Chip.">Reconstituting Organ-Level Lung Functions on a Chip.</a> Science. 328 (5986), 1662-1668 (2010).</li><li>Pihl, J., Sinclair, J., Sahlin, E., Karlsson, M., Petterson, F., J, O. l. o. f. s. s. o. n., Orwar, O. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+Gradient-Generating+Device+for+Pharmacological+Profiling.">Microfluidic Gradient-Generating Device for Pharmacological Profiling.</a> Anal. Chem. 77 (13), 3897-3903 (2005).</li><li>Fishler, R., Mulligan, M. K., Sznitman, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acinus-on-a-chip:+A+microfluidic+platform+for+pulmonary+acinar+flows.">Acinus-on-a-chip: A microfluidic platform for pulmonary acinar flows.</a> J. Biomech. 46 (16), 2817-2823 (2013).</li><li>Lindken, R., Rossi, M., Grosse, S., Westerweel, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Micro-Particle+Image+Velocimetry+(microPIV):+recent+developments,+applications,+and+guidelines.">Micro-Particle Image Velocimetry (microPIV): recent developments, applications, and guidelines.</a> Lab. Chip. 9 (17), 2551-2567 (2009).</li><li>Wereley, S. T., Meinhart, C. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Recent+Advances+in+Micro-Particle+Image+Velocimetry.">Recent Advances in Micro-Particle Image Velocimetry.</a> Annu. Rev. Fluid Mech. 42 (1), 557-576 (2010).</li><li>Bruus, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Theoretical+Microfluidics.">Theoretical Microfluidics.</a> Oxford Master Series in Condensed Matter Physics. , (2008).</li><li>Haefeli-Bleuer, B., Weibel, E. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Morphometry+of+the+human+pulmonary+acinus.">Morphometry of the human pulmonary acinus.</a> Anat. Rec. 220 (4), 401-414 (1988).</li></ol>

The authors have nothing to disclose.

A critical feature of the microfluidic acinar platform presented here is its ability to reproduce physiologically-realistic breathing motions that give rise to physiological flow profiles and velocities within acinar ducts and within alveoli. Since the microfluidic channels are produced with a relatively low aspect ratio (i.e., wd/h &#8776; 3.9, where wd is the duct width and h is the duct height), the measured flows show more plug-like ...

A detailed quantification of respiratory flow dynamics in the distal, alveolated regions of the lungs is paramount towards understanding airflow mixing in the pulmonary acinus and predicting the fate of inhaled aerosols in the deepest airways1&#8211;3. This latter aspect is of particular concern when addressing on the one hand the hazards of inhaled pollutant particles or conversely in seeking novel strategies for improved and targeted drug delivery of inhaled therapeutics to localized lung sites4, 5&#160;as well as for systemic delivery.
To date, respiratory flows in the deep pulmonary acinar regions have been typically investigated in silico using computational fluid dynamics (CFD) or alternatively in vitro with scaled-up experimental models following hydrodynamic similarity matching. In the past few decades, CFD methods have been increasingly applied to study acinar flow phenomena, from single alveolar models6, 7&#160;and alveolated ducts8&#8211;12&#160;to more elaborate in silico models that capture anatomically-realistic acinar tree structures with multiple generations of alveolated ducts and up to several hundreds of individual alveoli13&#8211;15.
Together, numerical efforts have been pivotal in shedding light on the role and influence of wall motion during breathing movements on ensuing acinar airflow patterns. In the absence of breathing motion, static alveoli feature recirculating flows within their cavities that exhibit no convective exchange of air between the acinar duct and the alveolus6, 7; in other words, alveolar flows would be entirely isolated from flows within the acinar trees and exchange of air would result uniquely from diffusive mechanisms. With the existence of cyclic expansions of the alveolar domain, however, alveolar flow topologies are drastically modified and the resulting flow patterns inside alveoli are intimately tied to the location of an alveolus along the acinar tree (e.g., proximal vs. distal generations).
In particular, it has been hypothesized in simulations that alveolar flow patterns are strongly influenced by the ratio of alveolar to ductal flow rates such that proximal generations of the pulmonary acinar tree, where this ratio is relatively large following mass conservation across a tree structure, feature complex recirculating flows inside the alveolar cavities with irreversible fluid pathlines. With each deeper acinar generation, the ratio of alveolar to ductal flow rates gradually decreases such that distal acinar generations exhibit more radial-like streamlines that are reminiscent of simple inflations and deflations of a balloon. With advances in modern imaging modalities, lung imaging data16, 17&#160;of rodents, including rat and mouse, have given rise to some of the first CFD simulations of anatomically-reconstructed acinar flows in reconstructed alveoli. Despite such promising progress, these recent studies are still limited to addressing airflow phenomena in terminal alveolar sacs only18, 19&#160;or a few alveoli surrounding a single duct20. As a result, state-of-the-art investigations of respiratory flow phenomena in the acinus remain dominated by studies focusing on generic anatomically-inspired geometries of the acinar environment2.
On the experimental side, various setups featuring an airway with one or several alveoli have been developed over the years21&#8211;24. Yet, there exists no experimental models of bifurcating alveolated airways that are capable of mimicking physiological respiration by expanding and contracting in a breathing-like fashion. Given a lack of attractive experimental platforms at hand, the study of acinar transport phenomena remains limited with regards to validating computational studies and critically, there remains a dearth of experimental data available. In recent years, Ma et al. (2009) have constructed a scaled-up rigid-wall model of an acinus consisting of three acinar generations; however, the lack of wall motion in this model limited its capability to capture realistic alveolar flow patterns under breathing conditions.
Other scaled-up experiments including a moving wall model based on anatomical data from cast replica were recently introduced25; however, since the model only captured the last two acinar generations (i.e., terminal sacs), it failed to capture the complex recirculating flows that characterize more proximal acinar generations. These latter examples of scaled-up experiments further underline the ongoing limitations with such approaches. Specifically, no existing experiment has thus far demonstrated the hypothesized transition from recirculating to radial flows along the acinus and thereby confirm numerical predictions of flow topologies hypothesized to exist in real pulmonary acinar trees7, 15. Perhaps most critically, scaled-up experiments are extremely limited in investigating inhaled particle transport and deposition dynamics26&#160;due to difficulties in matching all relevant non-dimensional parameters (e.g., particle diffusion, a critical transport mechanism for sub-micron particles, is completely neglected).
With ongoing experimental challenges, new experimental platforms that permit investigations of respiratory air flows and particle dynamics in complex moving walls acinar networks are sought. Here, an anatomically-inspired in vitro acinar model is introduced. This microfluidic platform mimics pulmonary acinar flows directly at the representative acinar scale, and broadens the growing range of pulmonary microfluidic models27, including bronchial liquid plug-flows28&#8211;30&#160;and the alveolar-capillary barrier31.
Namely, the present design features a simplified five generation alveolated airway tree with cyclically expanding and contracting walls, where cyclic motions are achieved by controlling pressure inside a water chamber which surrounds the thin PDMS lateral walls and where the top wall is deformed by an additional water chamber sitting directly above the acinar structure. Unlike common multilayer microfluidic devices, this chamber is simply formed by embedding the barrel section of a syringe inside the PDMS Device, and does not require preparation of an additional PDMS mold.
The miniaturized approach presented here offers a simple and versatile means for reproducing complicated acinar structures with moving walls as compared to scaled-up models while capturing the underlying characteristics of the acinar flow environment. This platform can be used for flow visualization using fluid-suspended particles inside the airways (see Representative Results below). In the near future, the model will be used with airborne particles for studying inhaled acinar particle dynamics.

<table><tbody><tr><td>Polydimethylsiloxane (PDMS) and curing agent</td><td>Dow Corning</td><td>(240)4019862</td><td>Sylgard&amp;reg; 184 Silicone Elastomer Kit</td></tr><tr><td>Plastipak 2 ml syringe</td><td>BD</td><td>300185</td><td></td></tr><tr><td>Norm-Ject Luer slip 1 ml syringe</td><td>Henke Sass Wolf </td><td>4010-200V0</td><td></td></tr><tr><td>1 mm Biopsy punch</td><td>Kai Medical</td><td>BP-10F</td><td></td></tr><tr><td>Laboratory Corona Treater</td><td>Electro-Technic Products</td><td>BD-20AC</td><td></td></tr><tr><td>PHD Ultra Syringe pump</td><td>Harvard apparatus</td><td>703006</td><td></td></tr><tr><td>Dyed red rqueous fluorescent particles</td><td>Thermo-Scientific</td><td></td><td>Uncatalloged 0.86 &amp;micro;m beads were used</td></tr><tr><td>Glycerin AR</td><td>Gadot</td><td>830131320</td><td></td></tr><tr><td>FlowMaster MITAS micro-particle image velocimetry (&amp;micro;PIV) system </td><td>LaVision</td><td>1108630</td><td></td></tr></tbody></table>

a microfluidic model of biomimetically breathing pulmonary acinar airways

Quantifying respiratory flow characteristics in the pulmonary acinar depths and how they influence inhaled aerosol transport is critical towards optimizing drug inhalation techniques as well as predicting deposition patterns of potentially toxic airborne particles in the pulmonary alveoli. Here, soft-lithography techniques are used to fabricate complex acinar-like airway structures at the truthful anatomical length-scales that reproduce physiological acinar flow phenomena in an optically accessible system. The microfluidic device features 5 generations of bifurcating alveolated ducts with periodically expanding and contracting walls. Wall actuation is achieved by altering the pressure inside water-filled chambers surrounding the thin PDMS acinar channel walls both from the sides and the top of the device. In contrast to common multilayer microfluidic devices, where the stacking of several PDMS molds is required, a simple method is presented to fabricate the top chamber by embedding the barrel section of a syringe into the PDMS mold. This novel microfluidic setup delivers physiological breathing motions which in turn give rise to characteristic acinar air-flows. In the current study, micro particle image velocimetry (&#181;PIV) with liquid suspended particles was used to quantify such air flows based on hydrodynamic similarity matching. The good agreement between &#181;PIV results and expected acinar flow phenomena suggest that the microfluidic platform may serve in the near future as an attractive in vitro tool to investigate directly airborne representative particle transport and deposition in the acinar regions of the lungs.

Computer-aided design (CAD) and microscope images of the in vitro acinar platform are presented in Fig. 1. The biomimetic acinar model features five generations of branching rectangular channels lined with alveolar-like cylindrical cavities (Fig. 1). Here, the model generations are numbered from generation 1 (for the most proximal generation) to generation 5 (for the most distal generation). Note that only the channel inlet leading to generation 1 is open to the outer environmen...

Watch this Scientific Journal Video about A Microfluidic Model of Biomimetically Breathing Pulmonary Acinar Airways at JoVE.com

A Microfluidic Model of Biomimetically Breathing Pulmonary Acinar Airways

Soft-lithography was utilized to produce a representative true-scale model of pulmonary alveolated airways that expand and contract periodically, mimicking physiological breathing motion. This platform recreates respiratory acinar flows on a chip, and is anticipated to facilitate experimental investigation of inhaled aerosol dynamics and deposition in the pulmonary acinus.

Quantifying respiratory flow characteristics in the pulmonary acinar depths and how they influence inhaled aerosol transport is critical towards ...

a-microfluidic-model-biomimetically-breathing-pulmonary-acinar

Research

JoVE Journal

Bioengineering

7.9K Views.  Technion - Israel Institute of Technology. Soft-lithography was utilized to produce a representative true-scale model of pulmonary alveolated airways that expand and contract periodically, mimicking physiological breathing motion. This platform recreates respiratory acinar flows on a chip, and is anticipated to facilitate experimental investigation of inhaled aerosol dynamics and deposition in the pulmonary acinus.

Video: A Microfluidic Model of Biomimetically Breathing Pulmonary Acinar Airways

The WinCF Model - An Inexpensive and Tractable Microcosm of a Mucus Plugged Bronchiole to Study the Microbiology of Lung Infections

Many chronic airway diseases result in mucus plugging of the airways. Lungs of an individual with cystic fibrosis are an exemplary case where their mucus-plugged bronchioles create a favorable habitat for microbial colonization. Various pathogens thrive in this environment interacting with each other and driving many of the symptoms associated with CF disease. Like any microbial community, the chemical conditions of their habitat have a significant impact on the community structure and dynamics. For example, different microorganisms thrive in differing levels of oxygen or other solute concentrations. This is also true in the CF lung, where oxygen concentrations are believed to drive community physiology and structure. The methods described here are designed to mimic the lung environment and grow pathogens in a manner more similar to that from which they cause disease. Manipulation of the chemical surroundings of these microbes is then used to study how the chemistry of lung infections governs its microbial ecology. The method, called the WinCF system, is based on artificial sputum medium and narrow capillary tubes meant to provide an oxygen gradient similar to that which exists in mucus-plugged bronchioles. Manipulating chemical conditions, such as the media pH of the sputum or antibiotics pressure, allows for visualization of the microbiological differences in those samples using colored indicators, watching for gas or biofilm production, or extracting and sequencing the nucleic acid contents of each sample.

The mucus plugged airways of cystic fibrosis (CF) patients are an ideal environment for microbial pathogens to thrive. The manuscript describes a novel method for studying the CF lung microbiome in an environment that mimics where they cause disease and how alterations of chemical conditions can drive microbial dynamics.

Many chronic airway diseases result in mucus plugging of the airways. Lungs of an individual with cystic fibrosis are an exemplary case where their ...

Immunology and Infection

Label-free Neutrophil Enrichment from Patient-derived Airway Secretion Using Closed-loop Inertial Microfluidics

Airway secretions contain a large number of immune-related cells, e.g., neutrophils, macrophages, and lymphocytes, which can be used as a major resource to evaluate a variety of pulmonary diseases, both for research and clinical purposes. However, due to the heterogeneous and viscous nature of patient mucus, there is currently no reliable dissociation method that does not damage the host immune cells in the patient airway secretion. In this research, we introduce a sample preparation method that uses inertial microfluidics for the patient&#39;s immune assessment. Regardless of the heterogeneous fluidic properties of the clinical samples, the proposed method recovers more than 95% of neutrophils from airway secretion samples that are diluted 1,000-fold with milliliters of clean saline. By recirculating the concentrated output stream to the initial sample reservoir, a high concentration, recovery, and purity of the immune cells are provided; recirculation is considered a trade-off to the single-run syringe-based operation of inertial microfluidics. The closed-loop operation of spiral microfluidics provides leukocytes without physical or chemical disturbance, as demonstrated by the phorbol 12-myristate 13-acetate (PMA)-induced elastase release of sorted neutrophils.

In this research, we demonstrate a label-free neutrophil separation method from clinical airway secretions using closed-loop operation of spiral inertial microfluidics. The proposed method would expand the clinical in vitro assays for various respiratory diseases.

Airway secretions contain a large number of immune-related cells, e.g., neutrophils, macrophages, and lymphocytes, which can be used as a major resource ...

Evaluating Regional Pulmonary Deposition using Patient-Specific 3D Printed Lung Models

Development of targeted therapies for pulmonary diseases is limited by the availability of preclinical testing methods with the ability to predict regional aerosol delivery. Leveraging 3D printing to generate patient-specific lung models, we outline the design of a high-throughput, in vitro experimental setup for quantifying lobular pulmonary deposition. This system is made with a combination of commercially available and 3D printed components and allows the flow rate through each lobe of the lung to be independently controlled. Delivery of fluorescent aerosols to each lobe is measured using fluorescence microscopy. This protocol has the potential to promote the growth of personalized medicine for respiratory diseases through its ability to model a wide range of patient demographics and disease states. Both the geometry of the 3D printed lung model and the air flow profile setting can be easily modulated to reflect clinical data for patients with varying age, race, and gender. Clinically relevant drug delivery devices, such as the endotracheal tube shown here, can be incorporated into the testing setup to more accurately predict a device&#8217;s capacity to target therapeutic delivery to a diseased region of the lung. The versatility of this experimental setup allows it to be customized to reflect a multitude of inhalation conditions, enhancing the rigor of preclinical therapeutic testing.

We present a high-throughput, in vitro method for quantifying regional pulmonary deposition at the lobe level using CT scan-derived, 3D printed lung models with tunable air flow profiles.

Development of targeted therapies for pulmonary diseases is limited by the availability of preclinical testing methods with the ability to predict ...

Microfluidic Model to Mimic Initial Event of Neovascularization

Neovascularization is usually initialized from an existing normal vasculature and the biomechanical microenvironment of endothelial cells (ECs) in the initial stage varies dramatically from the following process of neovascularization. Although there are plenty of models to simulate different stages of neovascularization, an in vitro 3D model that capitulates the initial process of neovascularization under the corresponding stimulations of normal vasculature microenvironments is still lacking. Here, we reconstructed an in vitro 3D model that mimics the initial event of neovascularization (MIEN). The MIEN model contains a microfluidic sprouting chip and an automatic control, highly efficient circulation system. A functional, perfusable microchannel coated with endothelium was formed and the process of sprouting was simulated in the microfluidic sprouting chip. The initially physiological microenvironment of neovascularization was recapitulated with the microfluidic control system, by which ECs would be exposed to high luminal shear stress, physiological transendothelial flow, and various vascular endothelial growth factor (VEGF) distributions simultaneously. The MIEN model can be readily applied to the study of neovascularization mechanism and holds a potential promise as a low-cost platform for drug screening and toxicology applications.

Here, we provide a microfluidic chip and an automatically controlled, highly efficient circulation microfluidic system that recapitulates the initial microenvironment of neovascularization, allowing endothelial cells (ECs) to be stimulated by high luminal shear stress, physiological level of transendothelial flow, and various vascular endothelial growth factor (VEGF) distribution simultaneously.

Neovascularization is usually initialized from an existing normal vasculature and the biomechanical microenvironment of endothelial cells (ECs) in the ...

A Microphysiological System to Study Leukocyte-Endothelial Cell Interaction during Inflammation

Leukocyte-endothelial cell interactions play an important role in inflammatory diseases such as sepsis. During inflammation, excessive migration of activated leukocytes across the vascular endothelium into key organs can lead to organ failure. A physiologically relevant biomimetic microfluidic assay (bMFA) has been developed and validated using several experimental and computational techniques, which can reproduce the entire leukocyte rolling/adhesion/migration cascade to study leukocyte-endothelial cell interactions. Microvascular networks obtained from in vivo images in rodents were digitized using a Geographic Information System (GIS) approach and microfabricated with polydimethylsiloxane (PDMS) on a microscope slide. To study the effect of shear rate and vascular topology on leukocyte-endothelial cell interactions, a Computational Fluid Dynamics (CFD) model was developed to generate a corresponding map of shear rates and velocities throughout the network. The bMFA enables the quantification of leukocyte-endothelial cells interactions, including rolling velocity, number of adhered leukocytes in response to different shear rates, number of migrated leukocytes, endothelial cell permeability, adhesion molecule expression and other important variables. Furthermore, by using human-related samples, such as human endothelial cells and leukocytes, bMFA provides a tool for rapid screening of potential therapeutics to increase their clinical translatability.

In this protocol, a biomimetic microfluid assay, which can reproduce a physiologically relevant microvascular environment and reproduce the entire leukocyte adhesion/migration cascade, is employed to study leukocyte-endothelial cell interactions in inflammatory disease.

Leukocyte-endothelial cell interactions play an important role in inflammatory diseases such as sepsis. During inflammation, excessive migration of ...

Imaging-Guided Bioreactor for Generating Bioengineered Airway Tissue

Repeated injury to airway tissue can impair lung function and cause chronic lung disease, such as chronic obstructive pulmonary disease. Advances in regenerative medicine and bioreactor technologies offer opportunities to produce lab-grown functional tissue and organ constructs that can be used to screen drugs, model disease, and engineer tissue replacements. Here, a miniaturized bioreactor coupled with an imaging modality that allows in situ visualization of the inner lumen of explanted rat trachea during in vitro tissue manipulation and&#160;culture is described. Using this bioreactor, the protocol demonstrates imaging-guided selective removal of endogenous cellular components while preserving the intrinsic biochemical features and ultrastructure of the airway tissue matrix. Furthermore, the delivery, uniform distribution, and subsequent prolonged culture of exogenous cells on the decellularized airway lumen with optical monitoring in situ are shown. The results highlight that the imaging-guided bioreactor can potentially be used to facilitate the generation of functional in vitro airway tissues.

The protocol describes an imaging-enabled bioreactor that allows the selective removal of the endogenous epithelium from the rat trachea and homogenous distribution of exogenous cells on the lumen surface, followed by long-term in vitro culture of the cell-tissue construct.

Repeated injury to airway tissue can impair lung function and cause chronic lung disease, such as chronic obstructive pulmonary disease. Advances in ...

Preparation and Structural Evaluation of Epithelial Cell Monolayers in a Physiologically Sized Microfluidic Culture Device

In vitro microfluidic experimentation holds great potential to reveal many insights into the microphysiological phenomena occurring in conditions such as acute respiratory distress syndrome (ARDS) and ventilator-induced lung injury (VILI). However, studies in microfluidic channels with dimensions physiologically relevant to the terminal bronchioles of the human lung currently face several challenges, especially due to difficulties in establishing appropriate cell culture conditions, including media flow rates, within a given culture environment. The presented protocol describes an image-based approach to evaluate the structure of NCI-H441 human lung epithelial cells cultured in an oxygen-impermeable microfluidic channel with dimensions physiologically relevant to the terminal bronchioles of the human lung. Using phalloidin-based filamentous-actin staining, the cytoskeletal structures of the cells are revealed by confocal laser scanning microscopy, allowing for the visualization of individual as well as layered cells. Subsequent quantification determines whether the cell culture conditions being employed are producing uniform monolayers suitable for further experimentation. The protocol describes cell culture and layer evaluation methods in microfluidic channels and traditional fixed-well environments. This includes channel construction, cell culture and requisite conditions, fixation, permeabilization and staining, confocal microscopic imaging, image processing, and data analysis.

The presented protocol describes the development and use of a phalloidin-based filamentous-actin staining technique with confocal laser scanning microscopy (CLSM) to visualize adherent cell layer structure in microfluidic dynamic-culture channels and traditional fixed-well static-culture chambers. This approach aids in evaluating cell layer confluency, monolayer formation, and layer-thickness uniformity.

In vitro microfluidic experimentation holds great potential to reveal many insights into the microphysiological phenomena occurring in conditions such as ...

Establishing a Lung-on-Chip Model for Respiratory Infection Studies

Immunocompetent Alveolus-on-Chip Model for Studying Alveolar Mucosal Immune Responses

We introduce an advanced immunocompetent lung-on-chip model designed to replicate the human alveolar structure and function. This innovative model employs a microfluidic-perfused biochip that supports an air-liquid interface mimicking the environment in the human alveoli. Tissue engineering is used to integrate key cellular components, including endothelial cells, macrophages, and epithelial cells, to create a representative tissue model of the alveolus. The model facilitates in-depth examinations of the mucosal immune responses to various pathogens, including viruses, bacteria, and fungi, thereby advancing our understanding of lung immunity. The primary goal of this protocol is to provide details for establishing this alveolus-on-chip model as a robust in vitro platform for infection studies, enabling researchers to closely observe and analyze the complex interactions between pathogens and the host's immune system within the pulmonary environment. This is achieved through the application of microfluidic-based techniques to simulate key physiological conditions of the human alveoli, including blood flow and biomechanical stimulation of endothelial cells, alongside maintaining an air-liquid interface crucial for the realistic exposure of epithelial cells to air. The model system is compatible with a range of standardized assays, such as immunofluorescence staining, cytokine profiling, and colony-forming unit (CFU)/plaque analysis, allowing for comprehensive insights into immune dynamics during infection. The Alveolus-on-chip is composed of essential cell types, including human distal lung epithelial cells (H441) and human umbilical vein endothelial cells (HUVECs) separated by porous polyethylene terephthalate (PET) membranes, with primary monocyte-derived macrophages strategically positioned between the epithelial and endothelial layers. The tissue model enhances the ability to dissect and analyze the nuanced factors involved in pulmonary immune responses in vitro. As a valuable tool, it should contribute to the advancement of lung research, providing a more accurate and dynamic in vitro model for studying the pathogenesis of respiratory infections and testing potential therapeutic interventions.

Author Spotlight: Developing a Microfluidic Lung-on-Chip Model for In-Depth Study of Human Immune Response and Infection Mechanisms

Lung-on-chip models surpass traditional 2D cultures by mimicking the air-liquid interface and endothelial cell perfusion, simulating blood flow and nutrient exchange crucial for lung physiology studies. This enhances lung research relevance, offering a dynamic, physiologically accurate environment to advance the understanding and treatment of respiratory infections.

We introduce an advanced immunocompetent lung-on-chip model designed to replicate the human alveolar structure and function. This innovative model employs ...

Multicellular Human Alveolar Model Composed of Epithelial Cells and Primary Immune Cells for Hazard Assessment

A human alveolar cell coculture model is described here for simulation of the alveolar epithelial tissue barrier composed of alveolar epithelial type II cells and two types of immune cells (i.e., human monocyte-derived macrophages [MDMs] and dendritic cells [MDDCs]). A protocol for assembling the multicellular model is provided. Alveolar epithelial cells (A549 cell line) are grown and differentiated under submerged conditions on permeable inserts in two-chamber wells, then combined with differentiated MDMs and MDDCs. Finally, the cells are exposed to an air-liquid interface for several days. As human primary immune cells need to be isolated from human buffy coats, immune cells differentiated from either fresh or thawed monocytes are compared in order to tailor the method based on experimental needs. The three-dimensional models, composed of alveolar cells with either freshly isolated or thawed monocyte-derived immune cells, show a statistically significant increase in cytokine (interleukins 6 and 8) release upon exposure to proinflammatory stimuli (lipopolysaccharide and tumor necrosis factor &#945;) compared to untreated cells. On the other hand, there is no statistically significant difference between the cytokine release observed in the cocultures. This shows that the presented model is responsive to proinflammatory stimuli in the presence of MDMs and MDDCs differentiated from fresh or thawed peripheral blood monocytes (PBMs). Thus, it is a powerful tool for investigations of acute biological response to different substances, including aerosolized drugs or nanomaterials.

Presented here is a protocol for primary human blood monocyte isolation as well as their differentiation into macrophages and dendritic cells and assembly with epithelial cells into a multicellular human lung model. Biological responses of cocultures composed of immune cells differentiated from either freshly isolated or thawed monocytes, upon exposure to proinflammatory stimuli, are compared.

A human alveolar cell coculture model is described here for simulation of the alveolar epithelial tissue barrier composed of alveolar epithelial type II ...

Biology

An Air-liquid Interface Bronchial Epithelial Model for Realistic, Repeated Inhalation Exposure to Airborne Particles for Toxicity Testing

For toxicity testing of airborne particles, air-liquid interface (ALI) exposure systems have been developed for in vitro tests in order to mimic realistic exposure conditions. This puts specific demands on the cell culture models. Many cell types are negatively affected by exposure to air (e.g., drying out) and only remain viable for a few days. This limits the exposure conditions that can be used in these models: usually relatively high concentrations are applied as a cloud (i.e., droplets containing particles, which settle down rapidly) within a short period of time. Such experimental conditions do not reflect realistic long-term exposure to low concentrations of particles. To overcome these limitations the use of a human bronchial epithelial cell line, Calu-3 was investigated. These cells can be cultured at ALI conditions for several weeks while retaining a healthy morphology and a stable monolayer with tight junctions. In addition, this bronchial model is suitable for testing the effects of repeated exposures to low, realistic concentrations of airborne particles using an ALI exposure system. This system uses a continuous airflow in contrast to other ALI exposure systems that use a single nebulization producing a cloud. Therefore, the continuous flow system is suitable for repeated and prolonged exposure to airborne particles while continuously monitoring the particle characteristics, exposure concentration, and delivered dose. Taken together, this bronchial model, in combination with the continuous flow exposure system, is able to mimic realistic, repeated inhalation exposure conditions that can be used for toxicity testing.

Described is the cell culture and exposure method of an in vitro bronchial model for realistic, repeated inhalation exposure to particles for toxicity testing.

For toxicity testing of airborne particles, air-liquid interface (ALI) exposure systems have been developed for in vitro tests in order to mimic realistic ...