1. Bringing Items into the Glovebox

1. Make sure that the item(s) to be brought in have been oven-dried (if glassware), and that containers are open.
2. Check the antechamber log to ensure that it is empty.
3. Fill the antechamber, either manually or electronically. Once filled with 1 atm of inert gas, close the inlet valve to isolate the chamber.
4. Open the antechamber to the outside, and place the items in the chamber.
5. Close the chamber, and evacuate (manually or electronically).
6. Fill in the log. Typically, users include their initials, items, and times of each cycle.
7. After the pressure dial reaches the minimum pressure, leave the antechamber under dynamic vacuum for 5 min for a small antechamber, and 20 min for a large antechamber.
8. Refill the antechamber with inert gas; typically, users will backfill to ~ 0.75 atm, as the inlet valve connects the main chamber to the antechamber.
9. Evacuate, and note the time.
10. Repeat steps 1.8-1.9, so that in total the antechamber has been evacuated 3x.
11. After 3 cycles, fill the antechamber with inert gas, and close off the insert gas supply.
12. Open the antechamber from inside the glovebox, and bring the items into the antechamber.
13. Close the antechamber door, and evacuate the chamber. When the glovebox is in its resting state, the chambers should be left under dynamic vacuum.
14. Note on the log that the procedure is complete, so that other users know that the antechamber is free.

2. Removing Items from the Glovebox

1. Look at the logbook to see the status of the antechamber. Be sure that it is not in use, and that the last operation was to bring an item into the antechamber. If the last operation was to bring an item out, quickly fill/evacuate the antechamber 3x with inert gas. This is to ensure no residual air is present (Equation 1) when opening the antechamber to the glovebox.
2. Fill the antechamber with inert gas, and close the valve connecting the inert gas supply to the chamber.
3. Open the antechamber from the inside of the glovebox.
4. Load the items into the chamber, and close the door.
5. From the outside of the glovebox, open the antechamber door and remove the items.
6. Evacuate the chamber.
7. Note that items were removed and the time on the logbook.

3. Ensuring a Good Working Environment

1. Testing the environment
   1. Turn off the circulator.
   2. Turn off any fans in the main glovebox chamber.
   3. Open a bottle of diethylzinc solution in hexanes (frequently 1.0 M).
   4. Gently swirl the bottle to replace the gas atmosphere in the bottle with the atmosphere in the box. If smoke emerges from the bottle, this is an indication that O₂, water, or an ether solvent is present in the atmosphere. If the atmosphere is compromised, the source of unwanted impurities should be identified.
   5. Turn the purge on for 5 min.
   6. Turn the purge off and the circulator on.
2. Making the radical indicator
   1. Turn off the circulator.
   2. In the glovebox, weigh out 5 mg of benzophenone and transfer this to a 20-mL scintillation vial.
   3. Weigh out ~ 500-1,000 mg of sodium and transfer this to the scintillation vial. Cap the vial.
   4. Add 20 mL of dry tetrahydrofuran (THF) and a stir bar. Cap the vial.
   5. Turn the purge on for at least 15 min before turning the circulator back on.
   6. Let the reaction stir for 48 h, or until the solution turns into a dark, inky purple solution. The solution should go from colorless to blue to purple, and there should be excess sodium at the bottom of the vial. This should give a solution with ~ 1.4 mM radical.
3. Testing solvent with the di-radical indicator
   Note: The newly synthesized radical can be used to test for O₂ and water impurities in solvents.
   1. If testing an ether solvent, turn the circulator off. Some groups require that the circulator is turned off before opening any chemical in the box.
   2. Add one drop of the radical solution to 10 mL of the test solvent. Solvents that can be tested using the radical include THF, diethyl ether, toluene, benzene, hexanes, and pentane. The radical will react with chlorinated solvents, pyridine, and other solvents that react with alkali metals.
   3. Observe the color of the solution over 1-2 min. A dry solvent will hold the color of the ketyl radical indefinitely. Realistically, the sample should hold the color for at least 1-2 min. Positive test colors are given in Table 1 below.
   4. Close all solvent bottles and turn the purge on for at least 15 min. Turn the circulator on again.