We thank Dr. Gilles Dupuis for critical reading of the manuscript. 
Funding
This work was supported by the Canadian Institutes for Health Research, grant # MOP-126173. C.M.D is a member of the Fonds de la Recherche en Sant&#233; (FRSQ)-funded Centre de Recherche Clinique &#201;tienne LeBel.

1. Preparazione di soluzioni per cellulare pH Calibrazione <ol><li> Aggiungere i seguenti composti da cinque tubi 50 ml coniche separati per preparare 5 soluzioni da utilizzare per la calibrazione: <ul><li> NaCl (1 ml di 1 M NaCl) (1 M NaCl = 0,58 g in 10 ml di H 2 0) </li><li> KCl (6,75 ml di 1 M KCl) (1 M KCl = 0,75 g in 10 ml di H 2 0) </li><li> Glucosio (1 ml di 1 M D-glucosio) (1M D-Glucosio = 1,80 g in 10 ml di H 2 0) </li><li> MgS0 4 (0,05 ml di 1 M MgSO 4) (1 M MgSO 4 = 1,20 g in 10 ml di H 2 0) </li><li> HEPES 20 mM (1 ml di 1M HEPES) (1 M HEPES = 2,38 g in 10 ml di H 2 0) </li><li> CaCl 2 (0,05 ml di 1M CaCl 2) (1 M CaCl 2 = 1,47 g in 10 ml di H 2 0) Preparare tutte le soluzioni a doppia distillata H 2 O (DDH 2 O). </li></ul></li><li> Completare ogni soluzione con 35 ml di DDH 2 O e mescolare con un agitatore magnetico fino a tantoluzione è raggiunto. </li><li> Regolare il pH di ciascuna soluzione con 1 N KOH o 1 N HCl per ottenere valori di pH 5.5, 6.0, 6.5, 7.0 e 7.5. Poi, regolare il volume con acqua deionizzata fino ad un volume finale di 50 ml. </li><li> Misura 5 mg di nigericin e aggiungerlo a 670 ml di EtOH assoluto per preparare un 10 mM nigericin soluzione stock. Attenzione: nigericin è altamente tossico e deve essere maneggiata con molta cura (guanti, occhiali di protezione e maschera). Miscelare la soluzione per inversione fino a quando il nigericin è completamente sciolto. </li><li> Aggiungere 0,05 ml di nigericin 10 mm (concentrazione finale 10 mM) ad ogni soluzione di taratura. Nigericina è uno ionoforo che aumenta la permeabilità della membrana cellulare e provoca equilibrazione di pH intracellulare ed extracellulare in presenza di una concentrazione depolarizzante di K + extracellulare. </li><li> Soluzioni di taratura possono essere memorizzati fino a 1 mese a 4 ° C </li></ol> 2. Preparazione cellulare <ol><li> Sotto un safet biologicoCappa y, cellule seme in 35 millimetri x 10 millimetri piatti di coltura in 2 ml di terreno di coltura supplementato con 10% di siero fetale bovino e antibiotici. Usare la quantità di cellule necessarie per garantire circa il 50% di confluenza dopo 24 ore. NOTA: Nei nostri esperimenti, usiamo la linea cellulare HT-1080 e la piastra 1 x 10 5 cellule per capsula di Petri. </li><li> Determinare il numero di piatti di coltura necessari per l&#39;esperimento e piastra 5 ulteriori piastre di coltura da utilizzare per la calibrazione. </li><li> Piatti di porre la cultura in un C 5% CO 2 incubatore 37 ° / per almeno 24 ore. </li></ol> 3. Preparazione di sonde pH-sensing <ol><li> Preparare una soluzione madre 1M della sonda pH fluorescente 8-idrossipirene-1, 3,6 acido trisolfonico, sale trisodico (HPTS / pyranine) in DDH 2 0. Questa soluzione deve essere conservato a temperatura ambiente e al riparo dalla luce. </li><li> Preparare una soluzione stock di 1 mM 5 - (e-6)-carbossilico seminaphthorhodafluor acetossimetilico estere acetato (C-SNARF-01:00; chiamato thereaopo SNARF-1) sciogliendo 1 mg di SNARF-1 in 1,76 ml di DMSO. Mescolare accuratamente pipettando ripetuta. SNARF-1 soluzione deve essere conservata a -20 ° C e al riparo dalla luce. </li></ol> 4. Etichettatura cellulare <ol><li> Sedici ore prima del live-cell imaging, aggiungere 2 ml di soluzione stock 1M HPTS (concentrazione finale 1 mm) per ogni piatto di coltura contenente 2 ml di terreno completo. </li><li> Riportare i piatti della cultura per l&#39;incubatore. La sonda HPTS è cell-impermeant, quindi etichetta organelli la sonda deve essere occupato da pinocitosi. Questa condizione richiede che incubazione delle cellule con HPTS vengono eseguite in medium siero supplementato cultura. </li><li> Dopo l&#39;incubazione con HPTS, lavare le cellule due volte con PBS sterile e aggiungere 2 ml di mezzo privo di siero per almeno 2 ore. Incubazione con SNARF-1 deve essere eseguita in terreno privo di siero perché siero può impedire l&#39;assorbimento della sonda. </li><li> Aggiungere 10 ml di un SNARF-1 soluzione stock 1 mm per ottenere afconcentrazione inale su 5 micron e consentono alle cellule di incubare per 20 min a 37 ° C, sotto la luce fioca. C-1-SNARF concentrazione e tempo di incubazione può variare a seconda del tipo cellulare. </li><li> Al termine dell&#39;incubazione, lavare le cellule due volte in PBS sterile e aggiungere 2 ml di mezzo privo di siero. </li></ol> 5. Aggiunta di pH modulatori <ol><li> Per valutare se il metodo può rilevare variazioni di pH nelle cellule, diversi reagenti che modulano pH intracellulare possono essere utilizzati: <ul><li> Bafilomycin A1, un inibitore specifico della V-ATPasi 5 </li><li> Na + / H + scambiatore isoforma 1 (NHE-1) 6 </li><li> NH 4 Cl, una base debole che aumenta intracellulare pH 7 </li></ul><ol><li> Preparare soluzioni madre dei reattivi di cui sopra: <ul><li> Bafilomycin A1: aggiungere 10 mg di bafilomycin A1 a 160 ml di DMSO per ottenere una soluzione stock di 100 micron </li><li> EIPA: aggiungere 25 mg di EIPA a 1.67 ml di metanolo per ottenuna concentrazione finale di 50 mM </li><li> NH 4 Cl: sciogliere 0,53 g di cloruro di ammonio in 10 ml di DDH 2 O per ottenere una concentrazione finale di 1 mM. </li></ul> Nota: Tutte le soluzioni di archivi devono essere conservati a 4 ° C ad eccezione di bafilomycin A1, che deve essere conservato a -20 ° C e al riparo dalla luce. </li><li> In piatti della cultura separati, aggiungere uno dei reagenti come descritto di seguito: <ul><li> 2 ml di 100 mM bafilomycin A1 (concentrazione finale 100 nm) </li><li> 1 ml di 50 mM EIPA (concentrazione finale 25 pm) </li><li> 40 ml di 1M NH 4 Cl (concentrazione finale 20 mM) </li></ul></li><li> Incubare le cellule per 30 min a 37 ° C. </li></ol></li><li> Procedere alla acquisizione delle immagini. </li></ol> 6. Specifiche tecniche di imaging microscopio live-cell e impostazioni di acquisizione <ol><li> Eseguire live-cell imaging usando un obiettivo 40X montato su una spettrale invertito confocale a scansione microscope dotato di un palco XY motorizzato, una camera che ospita fondo di vetro piatti della cultura in un (temperatura, umidità, CO 2) fase di incubatore ambiente controllato. </li><li> Lo strumento confocale (Olympus FV1000) qui usato è dotato di: <ul><li> Un diodo laser 405 nm </li><li> Un laser ad argon 40 mW (458 nm, 488 nm, 515 nm) </li><li> Un laser elio neon (543 nm) </li><li> Obiettivo Fluorite 10X, NA0.4 </li><li> Un obiettivo LUCPLFLN 40X, NA0.60 </li><li> Un obiettivo olio PLAPONSC PIANO APO 60X, NA1.4 </li><li> Uno specchio dicroico DM 405/458/488/543 </li><li> Un SDM 560 e un SDM 640 filtri dicroici </li><li> Un filtro barriera BA655-755 </li><li> Un BS20/80 divisore di fascio </li><li> Software di analisi dei dati per acquisizione ed elaborazione, </li></ul></li><li> Una volta che l&#39;incubatore fase si è riscaldata fino a 37 ° C e il microscopio è istituito, mettere un piatto di coltura precedentemente incubate con HPTS e SNARF-1 nella camera di imaging fase confocale. </li><li> Laopo l&#39;individuazione di una zona di interesse, regolare le impostazioni di acquisizione del software Figura 1. <ul><li> Impostare due set di canali virtuali. </li><li> Avviare la prima fase che corrisponde al HPTS eccitazione a 405 nm e la raccolta emissione a 505-525 nm e SNARF-1 eccitazione a 543 nm e la raccolta emissione a 570-600 nm. </li><li> Avviare la seconda fase che corrisponde alla HPTS eccitazione a 458 nm e la raccolta emissione a 505-525 nm e SNARF-1 eccitazione a 543 nm e la raccolta emissione a 640-650 nm. </li><li> L&#39;apertura confocale è impostato a 175 micron per default e apertura ottimale deve essere impostata manualmente a 300 micron. </li><li> Prendere Immagine impilando seriali sezioni ottiche orizzontali (800 x 800 pixel) da 0,4 micron di spessore. </li></ul></li></ol> NOTA: Un obiettivo 40X è utile osservare più celle contemporaneamente e funziona bene per la visualizzazione organello. Tuttavia, la risoluzione spaziale e l&#39;intensità del segnale sono better ottenuto utilizzando un obiettivo 60X olio. Inoltre, non c&#39;è eccitazione o di emissione di diafonia tra i due coloranti. 7. Taratura delle sonde di pH-sensing <ol><li> Prima della taratura, rimuovere terreno dalla piastra di coltura precedentemente incubate con HPTS e SNARF-1, lavare due volte con PBS sterile e poi aggiungere 2 ml di una delle cinque soluzioni di taratura. </li><li> Posizionare il piatto cultura nella camera di fase confocale. </li><li> Procedere al time-lapse acquisizione delle immagini secondo le seguenti impostazioni: <ol><li> Impostare il numero di immagini e tempi di durata degli intervalli per l&#39;esperimento. NOTA: Usiamo tipicamente un intervallo di 1 minuto tra le immagini fino a 30 min. </li><li> Programmare l&#39;otturatore per chiudere tra l&#39;acquisizione di ogni immagine. </li></ol></li><li> Registrare l&#39;intensità di fluorescenza per min in un foglio elettronico e determinare il momento in cui l&#39;intensità di fluorescenza è costante. PH intracellulare è generalmente stabile dopo 15 - 20 min. </li><li> Ripetere passaggi 7,1-7,4 utilizzando un nuovo piatto di coltura per ogni soluzione di calibrazione rimanente. </li></ol> 8. Acquisizione dati <ol><li> Una volta che la calibrazione è stato fatto, acquisire dati di esempio 4-5 campi scelti a caso contengono 15-20 cellule per campo. Due immagini sono ottenute per ciascun campo: uno per l&#39;etichettatura HPTS (vescicole) e il secondo per SNARF-1 etichettatura (citosol). </li><li> Fluorescenza di fondo (zona extracellulare) viene digitalmente sottratto dalle immagini fluorescenti di entrambe le sonde. Vescicole etichettati e citoplasma dei rispettivi immagini memorizzate sono state selezionate usando una maschera binaria. Per ogni sonda pH-sensing, intensità di fluorescenza sono misurati su una scala numerica (0-4,095 scala di livelli di grigio). Una intensità medio per tutti i pixel del organello o citoplasma è calcolato ei valori vengono utilizzati per calcolare i rapporti di fluorescenza. </li></ol> 9. Analisi dei dati <ol><li> I vari pacchetti software sono disponibili in commercio per l&#39;analisi dei dati. EsempioFluoView Software. </li><li> In un foglio di calcolo, i valori dei record e calcolare rapporti di fluorescenza come segue: Nel caso di HPTS, R = (F 458 nm / F 405 nm) e, nel caso di SNARF-1, R = (F 644 nm / F 584 nm ). </li><li> Tracciare i dati utilizzando software grafici scientifici come GraphPad Prism. La trama dovrebbe ritrarre rapporti di fluorescenza (asse y) in funzione del pH (asse X). Curva di raccordo è realizzato utilizzando la regressione non lineare. </li><li> Raccogliere intensità di fluorescenza dei campioni come descritto al punto 8.2 e calcolare rapporti di fluorescenza. Usare curve di calibrazione per trasformare i rapporti in valori di pH. </li></ol>

<ol>
	<li>Demaurex, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=pH+Homeostasis+of+cellular+organelles.">pH Homeostasis of cellular organelles.</a> News Physiol Sci. 17, 1-5 (2002).</li><li>Webb, B. A., Chimenti, M., Jacobson, M. P., Barber, D. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dysregulated+pH:+a+perfect+storm+for+cancer+progression.">Dysregulated pH: a perfect storm for cancer progression.</a> Nat Rev Cancer. 11, 671-677 (2011).</li><li>Hinton, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Function+of+a+subunit+isoforms+of+the+V-ATPase+in+pH+homeostasis+and+in+vitro+invasion+of+MDA-MB231+human+breast+cancer+cells.">Function of a subunit isoforms of the V-ATPase in pH homeostasis and in vitro invasion of MDA-MB231 human breast cancer cells.</a> J Biol Chem. 284, 16400-16408 (2009).</li><li>Overly, C. C., Lee, K. D., Berthiaume, E., Hollenbeck, P. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantitative+measurement+of+intraorganelle+pH+in+the+endosomal-lysosomal+pathway+in+neurons+by+using+ratiometric+imaging+with+pyranine.">Quantitative measurement of intraorganelle pH in the endosomal-lysosomal pathway in neurons by using ratiometric imaging with pyranine.</a> Proc Natl Acad Sci U S A. 92, 3156-3160 (1995).</li><li>Drose, S., Altendorf, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bafilomycins+and+concanamycins+as+inhibitors+of+V-ATPases+and+P-ATPases.">Bafilomycins and concanamycins as inhibitors of V-ATPases and P-ATPases.</a> J Exp Biol. 200, 1-8 (1997).</li><li>Pedersen, S. F., King, S. A., Nygaard, E. B., Rigor, R. R., Cala, P. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=NHE1+inhibition+by+amiloride-+and+benzoylguanidine-type+compounds.+Inhibitor+binding+loci+deduced+from+chimeras+of+NHE1+homologues+with+endogenous+differences+in+inhibitor+sensitivity.">NHE1 inhibition by amiloride- and benzoylguanidine-type compounds. Inhibitor binding loci deduced from chimeras of NHE1 homologues with endogenous differences in inhibitor sensitivity.</a> J Biol Chem. 282, 19716-19727 (2007).</li><li>Alfonso, A., Cabado, A. G., Vieytes, M. R., Botana, L. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Calcium-pH+crosstalks+in+rat+mast+cells:+cytosolic+alkalinization,+but+not+intracellular+calcium+release,+is+a+sufficient+signal+for+degranulation.">Calcium-pH crosstalks in rat mast cells: cytosolic alkalinization, but not intracellular calcium release, is a sufficient signal for degranulation.</a> Br J Pharmacol. 130, 1809-1816 (2000).</li><li>Han, J., Burgess, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fluorescent+indicators+for+intracellular+pH.">Fluorescent indicators for intracellular pH.</a> Chem Rev. 110, 2709-2728 (2010).</li><li>Giuliano, K. A., Gillies, R. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Determination+of+intracellular+pH+of+BALB/c-3T3+cells+using+the+fluorescence+of+pyranine.">Determination of intracellular pH of BALB/c-3T3 cells using the fluorescence of pyranine.</a> Anal Biochem. 167, 362-371 (1987).</li><li>Willoughby, D., Thomas, R., Schwiening, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+effects+of+intracellular+pH+changes+on+resting+cytosolic+calcium+in+voltage-clamped+snail+neurones.">The effects of intracellular pH changes on resting cytosolic calcium in voltage-clamped snail neurones.</a> J Physiol. 530, 405-416 (2001).</li></ol>

No conflict of interest declared.

Misura di pH quantitativa in live-cell imaging di diversi compartimenti cellulari è necessaria per misurare con precisione le variazioni di pH nelle risposte cellulari alle sfide esterne. Tuttavia, uno dei principali ostacoli che rimane è facile e specificamente i compartimenti cellulari. A questo proposito, alcuni studi hanno evidenziato l&#39;uso di HPTS come indicatore di pH intracellulare introdotto in cellule mediante elettroporazione o microiniezione 8-10. Queste tecniche soffrono di gravi inconvenien...

<table border="0" cellpadding="0" cellspacing="0" width="872">
	<tbody>
		<tr height="20">
			<td colspan="4" height="20" style="height:20px;width:872px;">Solutions for calibration</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Sodium chloride</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">L-11621</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Potassium chloride</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">M-12445</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">D-Glucose (dextrose)</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">D16-1</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Magnesium sulfate</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">M65-500</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">HEPES</td>
			<td style="width:136px;">Sigma-Aldrich</td>
			<td style="width:119px;">H3375</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Calcium chloride dihydrate</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">M-1612</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Deionized water</td>
			<td style="width:136px;">N/A</td>
			<td style="width:119px;">N/A</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Nigericin</td>
			<td style="width:136px;">Calbiochem</td>
			<td align="right" style="width:119px;">481990</td>
			<td>Toxic by inhalation or in contact with skin</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;"></td>
			<td style="width:136px;"></td>
			<td style="width:119px;"></td>
			<td style="width:315px;">Keep protected from the light at 4&#176;C</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;"></td>
			<td style="width:136px;"></td>
			<td style="width:119px;"></td>
			<td style="width:315px;"></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Culture dishes &#8709; 35mm</td>
			<td style="width:136px;">BD Biosciences</td>
			<td align="right" style="width:119px;">354456</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;"></td>
			<td style="width:136px;"></td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="20">
			<td colspan="4" height="20" style="height:20px;width:872px;">pH-sensing probes</td>
		</tr>
		<tr height="40">
			<td height="40" style="height:40px;width:303px;">8-Hydroxypyrene-1,3,6-trisulfonic acid (HPTS)</td>
			<td style="width:136px;">Life technologies</td>
			<td style="width:119px;">H-348</td>
			<td>Keep away from the light at room temperature</td>
		</tr>
		<tr height="40">
			<td height="40" style="height:40px;width:303px;">5-(and-6)-Carboxy SNARF&#174;-1, Acetoxymethyl Ester, Acetate</td>
			<td style="width:136px;">Life technologies</td>
			<td style="width:119px;">C-1271</td>
			<td>Keep away from the light and humidity at -20&#176;C</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;"></td>
			<td style="width:136px;"></td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Dimethyl Sufoxide (DMSO)</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">BP231-1&#160;</td>
			<td>Harmful</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;"></td>
			<td style="width:136px;"></td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="20">
			<td colspan="4" height="20" style="height:20px;width:872px;">Phosphate buffered saline (PBS) 100X</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Potassium chloride</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">M-12445</td>
			<td>20 g</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Sodium phosphate monobasic</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">S369-1</td>
			<td>115 g</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Potassium phosphate monobasic</td>
			<td style="width:136px;">J.T Baker</td>
			<td style="width:119px;">3246-01</td>
			<td>20 g</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Deionized water</td>
			<td style="width:136px;">N/A</td>
			<td style="width:119px;">N/A</td>
			<td>Bring to 1 L</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Autoclave and adjust pH to 7.4</td>
			<td style="width:136px;"></td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;"></td>
			<td style="width:136px;"></td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="20">
			<td colspan="4" height="20" style="height:20px;width:872px;">Phosphate buffered saline (PBS) 1X</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">PBS 100X</td>
			<td style="width:136px;">N/A</td>
			<td style="width:119px;">N/A</td>
			<td>50 mL</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Sodium chloride</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">L-11621</td>
			<td>40,5 g</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Deoinized water</td>
			<td style="width:136px;">N/A</td>
			<td style="width:119px;">N/A</td>
			<td>Bring to 5 L</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;"></td>
			<td style="width:136px;"></td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="20">
			<td colspan="4" height="20" style="height:20px;width:872px;">pH modulators</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">&#160;Bafilomycin A1</td>
			<td style="width:136px;">Sigma-Aldrich</td>
			<td style="width:119px;">B-1793</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">5-(N-Ethyl-N-isopropyl)amiloride (EIPA)</td>
			<td style="width:136px;">Sigma-Aldrich</td>
			<td style="width:119px;">A3085</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;width:303px;">Ammonium chloride</td>
			<td style="width:136px;">Fischer</td>
			<td style="width:119px;">A649-500</td>
			<td></td>
		</tr>
	</tbody>
</table>

simultaneous ph measurement in endocytic and cytosolic compartments in living cells using confocal microscopy

Intracellular pH is tightly regulated and differences in pH between the cytoplasm and organelles have been reported1. Regulation of cellular pH is crucial for homeostatic control of physiological processes that include: protein, DNA and RNA synthesis, vesicular trafficking, cell growth and cell division. Alterations in cellular pH homeostasis can lead to detrimental functional changes and promote progression of various diseases2. Various methods are available for measuring intracellular pH but very few of these allow simultaneous measurement of pH in the cytoplasm and in organelles. Here, we describe in detail a rapid and accurate method for the simultaneous measurement of cytoplasmic and organellar pH by using confocal microscopy on living cells3. This goal is achieved with the use of two pH-sensing ratiometric dyes that possess selective cellular compartment partitioning. For instance, SNARF-1 is compartmentalized inside the cytoplasm whereas HPTS is compartmentalized inside endosomal/lysosomal organelles. Although HPTS is commonly used as a cytoplasmic pH indicator, this dye can specifically label vesicles along the endosomal-lysosomal pathway after being taken up by pinocytosis3,4. Using these pH-sensing probes, it is possible to simultaneously measure pH within the endocytic and cytoplasmic compartments. The optimal excitation wavelength of HPTS varies depending on the pH while for SNARF-1, it is the optimal emission wavelength that varies. Following loading with SNARF-1 and HPTS, cells are cultured in different pH-calibrated solutions to construct a pH standard curve for each probe. Cell imaging by confocal microscopy allows elimination of artifacts and background noise. Because of the spectral properties of HPTS, this probe is better suited for measurement of the mildly acidic endosomal compartment or to demonstrate alkalinization of the endosomal/lysosomal organelles. This method simplifies data analysis, improves accuracy of pH measurements and can be used to address fundamental questions related to pH modulation during cell responses to external challenges.

Per la misura simultanea di pH sia intracellulare e compartimenti cellulari endosomal / lisosomiali, sono stati usati i fluorescenti sonde pH-sensing raziometrici Snarf-1 e HPTS. SNARF-1 è limitata al compartimento citosolico che HPTS permette di misurare raziometrica pH del vano endosomale / lisosomiale. Carico delle cellule con HPTS per 16 ore permette la sua localizzazione selettiva negli endosomi / lisosomi 4. Un tipico esempio di fluorescenza registrata da cellule HT-1080 caricato con le sonde pH-sensib...

Watch this Scientific Journal Video about Simultaneous pH Measurement in Endocytic and Cytosolic Compartments in Living Cells using Confocal Microscopy at JoVE.com

Simultaneous pH Measurement in Endocytic and Cytosolic Compartments in Living Cells using Confocal Microscopy

Several methods are available for measuring intracellular pH but very few of these allow simultaneous measurement of cytoplasmic and organellar pH. Here, we describe in detail a rapid and accurate methodology to simultaneously measure cytoplasmic and vesicular pH by ratiometric imaging of living cells.

La misurazione simultanea di pH in endocitosi e citosoliche scomparti nelle cellule viventi usando Microscopia confocale

Intracellular pH is tightly regulated and differences in pH between the cytoplasm and organelles have been reported1. Regulation of cellular pH is crucial ...

simultaneous-ph-measurement-endocytic-cytosolic-compartments-living

Research

JoVE Journal

Biology

14.9K Views.  Université de Sherbrooke. Several methods are available for measuring intracellular pH but very few of these allow simultaneous measurement of cytoplasmic and organellar pH. Here, we describe in detail a rapid and accurate methodology to simultaneously measure cytoplasmic and vesicular pH by ratiometric imaging of living cells. 

Video: Simultaneous pH Measurement in Endocytic and Cytosolic Compartments in Living Cells using Confocal Microscopy

Fluorescence-based Measurement of Store-operated Calcium Entry in Live Cells: from Cultured Cancer Cell to Skeletal Muscle Fiber

Store operated Ca2+ entry (SOCE), earlier termed capacitative Ca2+ entry, is a tightly regulated mechanism for influx of extracellular Ca2+ into cells to replenish depleted endoplasmic reticulum (ER) or sarcoplasmic reticulum (SR) Ca2+ stores1,2. Since Ca2+ is a ubiquitous second messenger, it is not surprising to see that SOCE plays important roles in a variety of cellular processes, including proliferation, apoptosis, gene transcription and motility. Due to its wide occurrence in nearly all cell types, including epithelial cells and skeletal muscles, this pathway has received great interest3,4. However, the heterogeneity of SOCE characteristics in different cell types and the physiological function are still not clear5-7.
The functional channel properties of SOCE can be revealed by patch-clamp studies, whereas a large body of knowledge about this pathway has been gained by fluorescence-based intracellular Ca2+ measurements because of its convenience and feasibility for high-throughput screening. The objective of this report is to summarize a few fluorescence-based methods to measure the activation of SOCE in monolayer cells, suspended cells and muscle fibers5,8-10. The most commonly used of these fluorescence methods is to directly monitor the dynamics of intracellular Ca2+ using the ratio of F340nm and F380nm (510 nm for emission wavelength) of the ratiometric Ca2+ indicator Fura-2. To isolate the activity of unidirectional SOCE from intracellular Ca2+ release and Ca2+ extrusion, a Mn2+ quenching assay is frequently used. Mn2+ is known to be able to permeate into cells via SOCE while it is impervious to the surface membrane extrusion processes or to ER uptake by Ca2+ pumps due to its very high affinity with Fura-2. As a result, the quenching of Fura-2 fluorescence induced by the entry of extracellular Mn2+ into the cells represents a measurement of activity of SOCE9. Ratiometric measurement and the Mn+2 quenching assays can be performed on a cuvette-based spectrofluorometer in a cell population mode or in a microscope-based system to visualize single cells. The advantage of single cell measurements is that individual cells subjected to gene manipulations can be selected using GFP or RFP reporters, allowing studies in genetically modified or mutated cells. The spatiotemporal characteristics of SOCE in structurally specialized skeletal muscle can be achieved in skinned muscle fibers by simultaneously monitoring the fluorescence of two low affinity Ca2+ indicators targeted to specific compartments of the muscle fiber, such as Fluo-5N in the SR and Rhod-5N in the transverse tubules9,11,12.

The extent of store-operated Ca2+ entry (SOCE) can be monitored using fluorescent Ca2+ indicators. Mn2+ quenching of such indicators assays SOCE in cultured cells and skeletal muscle fibers. A technique allowing spatial and temporal resolution of SOCE by confocal imaging of mechanically skinned muscle fibers is also described.

Basato sulla fluorescenza Misura Store-Entry operato di calcio in cellule vive: dal Cancer Cell coltura per fibra muscolare scheletrica

Store operated Ca2+ entry (SOCE), earlier termed capacitative Ca2+ entry, is a tightly regulated mechanism for influx of extracellular Ca2+ into cells to ...

Ricerca

Biologia

Measurement of Vacuolar and Cytosolic pH In Vivo in Yeast Cell Suspensions

Vacuolar and cytosolic pH are highly regulated in yeast cells and occupy a central role in overall pH homeostasis. We describe protocols for ratiometric measurement of pH in vivo using pH-sensitive fluorophores localized to the vacuole or cytosol. Vacuolar pH is measured using BCECF, which localizes to the vacuole in yeast when introduced into cells in its acetoxymethyl ester form. Cytosolic pH is measured with a pH-sensitive GFP expressed under control of a yeast promoter, yeast pHluorin. Methods for measurement of fluorescence ratios in yeast cell suspensions in a fluorimeter are described. Through these protocols, single time point measurements of pH under different conditions or in different yeast mutants have been compared and changes in pH over time have been monitored. These methods have also been adapted to a fluorescence plate reader format for high-throughput experiments. Advantages of ratiometric pH measurements over other approaches currently in use, potential experimental problems and solutions, and prospects for future use of these techniques are also described.

Measurement of Vacuolar and Cytosolic pH In Vivo in Yeast Cell Suspensions

Vacuolar and cytosolic pH can be measured in live yeast (S. cerevisiae) cells using ratiometric fluorescent dyes localized to specific cellular compartments. We describe procedures for measuring vacuolar pH with BCECF-AM, which localizes to the vacuole in yeast, and cytosolic pH with a cytosolic ratiometric pH-sensitive GFP (yeast pHluorin).

Misurazione di pH vacuolare e di Cytosolic<em&gt; In Vivo</em&gt; In Lievito Cell Sospensioni

Vacuolar and  cytosolic pH are highly regulated in yeast cells and occupy a central role in  overall pH homeostasis. We describe  protocols for ...

Analyzing Craniofacial Morphogenesis in Zebrafish Using 4D Confocal Microscopy

Time-lapse imaging is a technique that allows for the direct observation of the process of morphogenesis, or the generation of shape. Due to their optical clarity and amenability to genetic manipulation, the zebrafish embryo has become a popular model organism with which to perform time-lapse analysis of morphogenesis in living embryos. Confocal imaging of a live zebrafish embryo requires that a tissue of interest is persistently labeled with a fluorescent marker, such as a transgene or injected dye. The process demands that the embryo is anesthetized and held in place in such a way that healthy development proceeds normally. Parameters for imaging must be set to account for three-dimensional growth and to balance the demands of resolving individual cells while getting quick snapshots of development. Our results demonstrate the ability to perform long-term in vivo imaging of fluorescence-labeled zebrafish embryos and to detect varied tissue behaviors in the cranial neural crest that cause craniofacial abnormalities. Developmental delays caused by anesthesia and mounting are minimal, and embryos are unharmed by the process. Time-lapse imaged embryos can be returned to liquid medium and subsequently imaged or fixed at later points in development. With an increasing abundance of transgenic zebrafish lines and well-characterized fate mapping and transplantation techniques, imaging any desired tissue is possible. As such, time-lapse in vivo imaging combines powerfully with zebrafish genetic methods, including analyses of mutant and microinjected embryos.

Time-lapse confocal imaging is a powerful technique useful for characterizing embryonic development. Here, we describe the methodology and characterize craniofacial morphogenesis in wild-type, as well as pdgfra, smad5, and smo mutant embryos.

Analizzando craniofacciale morfogenesi in Zebrafish Uso 4D Microscopia confocale

Time-lapse imaging is a technique that allows for the direct observation of the process of morphogenesis, or the generation of shape. Due to their optical ...

In vivo Clonal Tracking of Hematopoietic Stem and Progenitor Cells Marked by Five Fluorescent Proteins using Confocal and Multiphoton Microscopy

We developed and validated a fluorescent marking methodology for clonal tracking of hematopoietic stem and progenitor cells (HSPCs) with high spatial and temporal resolution to study in vivo hematopoiesis using the murine bone marrow transplant experimental model. Genetic combinatorial marking using lentiviral vectors encoding fluorescent proteins (FPs) enabled cell fate mapping through advanced microscopy imaging. Vectors encoding five different FPs: Cerulean, EGFP, Venus, tdTomato, and mCherry were used to concurrently transduce HSPCs, creating a diverse palette of color marked cells. Imaging using confocal/two-photon hybrid microscopy enables simultaneous high resolution assessment of uniquely marked cells and their progeny in conjunction with structural components of the tissues. Volumetric analyses over large areas reveal that spectrally coded HSPC-derived cells can be detected non-invasively in various intact tissues, including the bone marrow (BM), for extensive periods of time following transplantation. Live studies combining video-rate multiphoton and confocal time-lapse imaging in 4D demonstrate the possibility of dynamic cellular and clonal tracking in a quantitative manner.

In vivo Clonal Tracking of Hematopoietic Stem and Progenitor Cells Marked by Five Fluorescent Proteins using Confocal and Multiphoton Microscopy

Combinatorial 5 fluorescent proteins marking of hematopoietic stem and progenitor cells allows in vivo clonal tracking via confocal and two-photon microscopy, providing insights into bone marrow hematopoietic architecture during regeneration. This method allows non-invasive fate mapping of spectrally-coded HSPCs-derived cells in intact tissues for extensive periods of time following transplantation.

In vivo clonale Monitoraggio di staminali ematopoietiche e cellule progenitrici Contrassegnato da cinque proteine ​​fluorescenti che utilizzano confocale e microscopia Multiphoton

We developed and validated a fluorescent marking methodology for clonal tracking of hematopoietic stem and progenitor cells (HSPCs) with high spatial and ...

Cytosolic Calcium Measurements in Renal Epithelial Cells by Flow Cytometry

A variety of cellular processes, both physiological and pathophysiological, require or are governed by calcium, including exocytosis, mitochondrial function, cell death, cell metabolism and cell migration to name but a few. Cytosolic calcium is normally maintained at low nanomolar concentrations; rather it is found in high micromolar to millimolar concentrations in the endoplasmic reticulum, mitochondrial matrix and the extracellular compartment. Upon stimulation, a transient increase in cytosolic calcium serves to signal downstream events. Detecting changes in cytosolic calcium is normally performed using a live cell imaging set up with calcium binding dyes that exhibit either an increase in fluorescence intensity or a shift in the emission wavelength upon calcium binding. However, a live cell imaging set up is not freely accessible to all researchers. Alternative detection methods have been optimized for immunological cells with flow cytometry and for non-immunological adherent cells with a fluorescence microplate reader. Here, we describe an optimized, simple method for detecting changes in epithelial cells with flow cytometry using a single wavelength calcium binding dye. Adherent renal proximal tubule epithelial cells, which are normally difficult to load with dyes, were loaded with a fluorescent cell permeable calcium binding dye in the presence of probenecid, brought into suspension and calcium signals were monitored before and after addition of thapsigargin, tunicamycin and ionomycin.

Calcium is involved in numerous physiological and pathophysiological signaling pathways. Live cell imaging requires specialized equipment and can be time consuming. A quick, simple method using a flow cytometer to determine relative changes in cytosolic calcium in adherent epithelial cells brought into suspension was optimized.

Misure calcio citosolico nelle cellule epiteliali renali mediante citometria di flusso

A variety of cellular processes, both physiological and pathophysiological, require or are governed by calcium, including exocytosis, mitochondrial ...

High-resolution Time-lapse Imaging and Automated Analysis of Microtubule Dynamics in Living Human Umbilical Vein Endothelial Cells

The physiological process by which new vasculature forms from existing vasculature requires specific signaling events that trigger morphological changes within individual endothelial cells (ECs). These processes are critical for homeostatic maintenance such as wound healing, and are also crucial in promoting tumor growth and metastasis. EC morphology is defined by the organization of the cytoskeleton, a tightly regulated system of actin and microtubule (MT) dynamics that is known to control EC branching, polarity and directional migration, essential components of angiogenesis. To study MT dynamics, we used high-resolution fluorescence microscopy coupled with computational image analysis of fluorescently-labeled MT plus-ends to investigate MT growth dynamics and the regulation of EC branching morphology and directional migration. Time-lapse imaging of living Human Umbilical Vein Endothelial Cells (HUVECs) was performed following transfection with fluorescently-labeled MT End Binding protein 3 (EB3) and Mitotic Centromere Associated Kinesin (MCAK)-specific cDNA constructs to evaluate effects on MT dynamics. PlusTipTracker software was used to track EB3-labeled MT plus ends in order to measure MT growth speeds and MT growth lifetimes in time-lapse images. This methodology allows for the study of MT dynamics and the identification of how localized regulation of MT dynamics within sub-cellular regions contributes to the angiogenic processes of EC branching and migration.

Protocols for Human Umbilical Vein Endothelial Cell (HUVEC) culture, transient transfection of fluorescently-labeled markers of microtubule growth, live-cell imaging and automated analysis of interphase microtubule growth dynamics are detailed.

Ad alta risoluzione Time-lapse imaging e analisi automatizzata dei microtubuli Dynamics in Living ombelicale umano cellule endoteliali Vena

The physiological process by which new vasculature forms from existing vasculature requires specific signaling events that trigger morphological changes ...

Simultaneous Measurement of Mitochondrial Calcium and Mitochondrial Membrane Potential in Live Cells by Fluorescent Microscopy

Apart from their essential role in generating ATP, mitochondria also act as local calcium (Ca2+) buffers to tightly regulate intracellular Ca2+ concentration. To do this, mitochondria utilize the electrochemical potential across their inner membrane (&#916;&#936;m) to sequester Ca2+. The influx of Ca2+ into the mitochondria stimulates three rate-limiting dehydrogenases of the citric acid cycle, increasing electron transfer through the oxidative phosphorylation (OXPHOS) complexes. This stimulation maintains &#916;&#936;m, which is temporarily dissipated as the positive calcium ions cross the mitochondrial inner membrane into the mitochondrial matrix.
We describe here a method for simultaneously measuring mitochondria Ca2+ uptake and &#916;&#936;m in live cells using confocal microscopy. By permeabilizing the cells, mitochondrial Ca2+ can be measured using the fluorescent Ca2+ indicator Fluo-4, AM, with measurement of &#916;&#936;m using the fluorescent dye tetramethylrhodamine, methyl ester, perchlorate (TMRM). The benefit of this system is that there is very little spectral overlap between the fluorescent dyes, allowing accurate measurement of mitochondrial Ca2+ and &#916;&#936;m simultaneously. Using the sequential addition of Ca2+ aliquots, mitochondrial Ca2+ uptake can be monitored, and the concentration at which Ca2+ induces mitochondrial membrane permeability transition and the loss of &#916;&#936;m determined.

Mitochondria can utilize the electrochemical potential across their inner membrane (&#916;&#936;m) to sequester calcium (Ca2+), allowing them to shape cytosolic Ca2+ signaling within the cell. We describe a method for simultaneously measuring mitochondria Ca2+ uptake and &#916;&#936;m in live cells using fluorescent dyes and confocal microscopy.

Misurazione simultanea di mitocondriale calcio e mitocondriale potenziale di membrana in cellule vive di Microscopia fluorescente

Apart from their essential role in generating ATP, mitochondria also act as local calcium (Ca2+) buffers to tightly regulate intracellular Ca2+ ...

A Graphical User Interface for Software-assisted Tracking of Protein Concentration in Dynamic Cellular Protrusions

Filopodia are dynamic, finger-like cellular protrusions associated with migration and cell-cell communication. In order to better understand the complex signaling mechanisms underlying filopodial initiation, elongation and subsequent stabilization or retraction, it is crucial to determine the spatio-temporal protein activity in these dynamic structures. To analyze protein function in filopodia, we recently developed a semi-automated tracking algorithm that adapts to filopodial shape-changes, thus allowing parallel analysis of protrusion dynamics and relative protein concentration along the whole filopodial length. Here, we present a detailed step-by-step protocol for optimized cell handling, image acquisition and software analysis. We further provide instructions for the use of optional features during image analysis and data representation, as well as troubleshooting guidelines for all critical steps along the way. Finally, we also include a comparison of the described image analysis software with other programs available for filopodia quantification. Together, the presented protocol provides a framework for accurate analysis of protein dynamics in filopodial protrusions using image analysis software.

We present a software solution for semi-automated tracking of relative protein concentration along the length of dynamic cellular protrusions.

Un&#39;interfaccia utente grafica per il monitoraggio assistito della concentrazione di proteine ​​in protrusioni cellulari dinamiche

Filopodia are dynamic, finger-like cellular protrusions associated with migration and cell-cell communication. In order to better understand the complex ...

Probing mRNA Kinetics in Space and Time in Escherichia coli using Two-Color Single-Molecule Fluorescence In Situ Hybridization

Single-molecule fluorescence in situ hybridization (smFISH) allows for counting the absolute number of mRNAs in individual cells. Here, we describe an application of smFISH to measure the rates of transcription and mRNA degradation in Escherichia coli. As smFISH is based on fixed cells, we perform smFISH at multiple time points during a time-course experiment, i.e., when cells are undergoing synchronized changes upon induction or repression of gene expression. At each time point, sub-regions of an mRNA are spectrally distinguished to probe transcription elongation and premature termination. The outcome of this protocol also allows for analyzing intracellular localization of mRNAs and heterogeneity in mRNA copy numbers among cells. Using this protocol many samples (~50) can be processed within 8 h, like the amount of time needed for just a few samples. We discuss how to apply this protocol to study the transcription and degradation kinetics of different mRNAs in bacterial cells.

Probing mRNA Kinetics in Space and Time in Escherichia coli using Two-Color Single-Molecule Fluorescence In Situ Hybridization

This protocol describes an application of single-molecule fluorescence in situ hybridization (smFISH) to measure the in vivo kinetics of mRNA synthesis and degradation.

Sondare la cinetica dell'mRNA nello spazio e nel tempo in Escherichia coli utilizzando la fluorescenza a singola molecola a due colori in ibridazione situ

Single-molecule fluorescence in situ hybridization (smFISH) allows for counting the absolute number of mRNAs in individual cells. Here, we describe an ...

Measurement of 3-Dimensional cAMP Distributions in Living Cells using 4-Dimensional (x, y, z, and &lambda;) Hyperspectral FRET Imaging and Analysis

Cyclic AMP is a second messenger that is involved in a wide range of cellular and physiological activities. Several studies suggest that cAMP signals are compartmentalized, and that compartmentalization contributes to signaling specificity within the cAMP signaling pathway. The development of F&#1255;rster resonance energy transfer (FRET) based biosensors has furthered the ability to measure and visualize cAMP signals in cells. However, these measurements are often confined to two spatial dimensions, which may result in misinterpretation of data. To date, there have been only very limited measurements of cAMP signals in three spatial dimensions (x, y, and z), due to the technical limitations in using FRET sensors that inherently exhibit low signal to noise ratio (SNR). In addition, traditional filter-based imaging approaches are often ineffective for accurate measurement of cAMP signals in localized subcellular regions due to a range of factors, including spectral crosstalk, limited signal strength, and autofluorescence. To overcome these limitations and allow FRET-based biosensors to be used with multiple fluorophores, we have developed hyperspectral FRET imaging and analysis approaches that provide spectral specificity for calculating FRET efficiencies and the ability to spectrally separate FRET signals from confounding autofluorescence and/or signals from additional fluorescent labels. Here, we present the methodology for implementing hyperspectral FRET imaging as well as the need to construct an appropriate spectral library that is neither undersampled nor oversampled to perform spectral unmixing. While we present this methodology for measurement of three-dimensional cAMP distributions in pulmonary microvascular endothelial cells (PMVECs), this methodology could be used to study spatial distributions of cAMP in a range of cell types.

Measurement of 3-Dimensional cAMP Distributions in Living Cells using 4-Dimensional x, y, z, and &amp;lambda; Hyperspectral FRET Imaging and Analysis

Due to inherent low signal-to-noise ratio (SNR) of F&#1255;rster resonance energy transfer (FRET) based sensors, measurement of cAMP signals has been challenging, especially in three spatial dimensions. Here, we describe a hyperspectral FRET imaging and analysis methodology that allows measurement of cAMP distribution in three spatial dimensions.

Misurazione di distribuzioni cAMP tridimensionali in cellule viventi utilizzando imaging e analisi FRET iperspettrale a 4 dimensioni (x, y, z e λ)

Cyclic AMP is a second messenger that is involved in a wide range of cellular and physiological activities. Several studies suggest that cAMP signals are ...