Synthesis of Ligand-free CdS Nanoparticles within a Sulfur Copolymer Matrix

Podsumowanie

Herein we present a method to synthesize ligand-free cadmium sulfide (CdS) nanoparticles based on a unique sulfur copolymer. The sulfur copolymer operates as a high temperature solvent and a sulfur source during the nanoparticle synthesis and stabilizes the nanoparticles after the reaction.

Streszczenie

Aliphatic ligands are typically used during the synthesis of nanoparticles to help mediate their growth in addition to operating as high-temperature solvents. These coordinating ligands help solubilize and stabilize the nanoparticles while in solution, and can influence the resulting size and reactivity of the nanoparticles during their formation. Despite the ubiquity of using ligands during synthesis, the presence of aliphatic ligands on the nanoparticle surface can result in a number of problems during the end use of the nanoparticles, necessitating further ligand stripping or ligand exchange procedures. We have developed a way to synthesize cadmium sulfide (CdS) nanoparticles using a unique sulfur copolymer. This sulfur copolymer is primarily composed of elemental sulfur, which is a cheap and abundant material. The sulfur copolymer has the advantages of operating both as a high temperature solvent and as a sulfur source, which can react with a cadmium precursor during nanoparticle synthesis, resulting in the generation of ligand free CdS. During the reaction, only some of the copolymer is consumed to produce CdS, while the rest remains in the polymeric state, thereby producing a nanocomposite material. Once the reaction is finished, the copolymer stabilizes the nanoparticles within a solid polymeric matrix. The copolymer can then be removed before the nanoparticles are used, which produces nanoparticles that do not have organic coordinating ligands. This nascent synthesis technique presents a method to produce metal-sulfide nanoparticles for a wide variety of applications where the presence of organic ligands is not desired.

Wprowadzenie

Although proven useful for synthesis, conventional aliphatic ligands present a number of challenges for the implementation of nanoparticles in photonic and electrochemical devices. Aliphatic ligands are highly insulating, hydrophobic, and constitute a significant barrier to electrochemical surface reactions.¹ Accordingly, several studies have developed ligand exchange and ligand stripping protocols that replace these aliphatic ligands with functional moieties or that strip away the ligands to reveal a bare nanoparticle surface.^1-3 These reactions, however, pose several intrinsic problems. They significantly add to the complexity of the synthetic process, do not always go to completion, and can deteriorate the surface of the nanoparticles, which can in turn impose significant problems during device fabrication when using these techniques.⁴

We have developed a sulfur copolymer that can be used as both a high temperature solvent and sulfur source during the synthesis of CdS nanoparticles.⁵ This copolymer is based on a network copolymer developed by Chung et al. that uses elemental sulfur and 1,3-diisopropenylbenzene (DIB).⁶ In our case, a methylstyrene monomer is implemented instead of DIB. The methylstyrene monomer limits cross-linking reactions, which would otherwise produce a high molecular weight network copolymer.^5,6 The presence of only one vinylic functional group on the methylstyrene monomer promotes the formation of oligomeric radicals once heated, which allows the sulfur copolymer to operate as a liquid solvent and sulfur source in parallel during the nanoparticle synthesis.⁵ Specifically, the sulfur polymer is produced by heating elemental sulfur to 150 °C, which causes the S₈ rings to transition into a linearly structured liquid sulfur diradical form. Next, methylstyrene is injected into the liquid sulfur in a 1:50 molar ratio of methylstyrene molecules to sulfur atoms.⁵ The methylstyrene double bond reacts with the sulfur chains to produce the copolymer, as presented in Figure 1.⁵ The sulfur copolymer is then cooled and the cadmium precursor is added. This mixture is then reheated to 200 °C, during which, the sulfur copolymer melts and the nanoparticle nucleation and growth processes are initiated within the solution.⁵ A 20:1 molar ratio of sulfur to cadmium precursor is used, so that only some of the sulfur is consumed during the reaction.⁵ This copolymer stabilizes the nanoparticles by suspending them within a solid polymer matrix once the reaction has been terminated.⁵ The copolymer can be removed after the synthesis, resulting in the production of CdS nanoparticles that do not have organic coordinating ligands, as depicted in Figure 2.⁵

The synthetic method presented in this work is relatively simple in comparison with other methods presented in the literature.^1-3,7 It is applicable for a diverse range of applications where traditional ligated nanoparticles have proven problematic or undesirable. This technique can open doors to higher throughput testing, where one batch of nanoparticles can be used to examine a complete spectrum of subsequent functionalizations without the need for complex and time consuming ligand stripping or exchange procedures.^2,4,8,9 These unligated nanoparticles also offer opportunities to reduce the number of carbon defects commonly observed in printed nanoparticle devices, by eliminating the carbon source.^10-16 This detailed protocol is intended to help others implement this new method and to help spur its active use in a variety of fields that will find it of particular significance.

Protokół

Caution: Cadmium precursors are highly toxic and must be handled with great care. Wear proper protective equipment, use appropriate engineering controls and consult relevant materials safety data sheets (MSDS). In addition, the formation of nanoparticles may present additional hazards. The reactions described herein are conducted with a standard vacuum gas manifold, in order to conduct the experiments within an inert atmosphere. All chemicals were purchased commercially and used as received. This protocol is based upon a previously developed synthetic method, which we recently described elsewhere.⁵

1. Sulfur Copolymer Synthesis

1. Preparation of Molten Elemental Sulfur
   1. Place elemental sulfur (4 g, 124.8 mmol, S₈, 99.5%) in a 50 ml three neck flask with an attached condenser and temperature probe. Perform pump and purge cycles with vacuum and nitrogen several times.
   2. Heat under nitrogen to 150 °C with stirring, which will cause the sulfur to become a yellow colored liquid.
2. Preparation of Sulfur Copolymer
   1. Once all of the sulfur has dissolved into the liquid, immediately inject α-methylstyrene (330 µl, 2.5 mmol, 99%) into the solution.
   2. Heat solution to 185 °C with stirring at 500 rpm for 10 min. As the copolymer forms, the solution will change color from yellow to orange, finally producing a deep red color.
   3. Remove the solution from heat and cool to room temperature. As it cools, the copolymer will slowly crystallize to form an orange rubbery solid. At this stage, the copolymer can be stored at room temperature for a subsequent synthesis or it can be used immediately.

2. CdS Nanoparticle Synthesis

1. Add cadmium acetylacetonate (Cd(acac), 900 mg, 2.9 mmol 99.9%) to the three neck flask from the previous step, so that the powder is placed evenly on top of the solid sulfur copolymer (4.0 g, 116 mmol).
2. Perform pump and purge cycles on the flask with nitrogen and vacuum several times.
3. Heat the solution to 200 °C under nitrogen with stirring. The sulfur copolymer will melt and mix with the cadmium precursor, and the nanoparticle nucleation and growth processes will begin.
4. Allow the nanoparticles to grow for 30 min.
   Note: Varying the reaction time will influence the growth of the nanoparticles, so it is possible to tune the final size of the nanoparticles.⁵ A 30 min reaction time will with a size range of 7-10 nm.⁵
5. Remove the solution from heat and allow to cool to room temperature.
6. Once cooled, remove the solid nanocomposite from the flask and store at room temperature.

3. Remove the Sulfur Copolymer and Isolate the Nanoparticles 

1. Removal of the Sulfur Copolymer
   1. Place the nanocomposite (200 mg) in a 20 ml glass vial and add chloroform (20 ml).
   2. Place the vial in an ultrasonicator and sonicate for 1 hr, to break up the nanocomposite and suspend the nanoparticles within the solution.
   3. Separate the solution into two 30 ml centrifuge tubes and add another 20 ml of chloroform to each.
   4. Centrifuge the solution at 8,736 x g (relative centrifugal force) for 15 min.
   5. Decant the sulfur copolymer from the centrifuge tubes, making sure to not disturb the settled nanoparticles.
2. Isolation of the Nanoparticles
   1. Re-disperse the settled nanoparticles by adding chloroform to each centrifuge tube (30 ml) and sonicate for 15 min.
   2. Repeat the steps described in sections 3.1.4, 3.1.5 and 3.2.1 three more times to ensure that all of the sulfur copolymer has been removed. Once all of the sulfur copolymer is removed, the decanted solution will no longer have an orange color.
   3. Collect the final nanoparticles by adding chloroform (2 ml) to each centrifuge tube.
   4. Combine the collected nanoparticles in one 20 ml glass vial (4 ml solution total) and place the glass vial under vacuum to remove all of the chloroform and to dry the nanoparticles. At this stage, the mass of the resulting nanoparticles can be determined and compared to the starting mass of the precursors in order to determine the yield of the reaction using molar ratios of the starting material and product.

4. Characterize the CdS Nanoparticles

1. Transmission Electron Microscopy
   1. Dilute the isolated nanoparticles (20 mg) in chloroform (20 ml) and ultrasonicate for 1 hr.
   2. Dilute this solution in chloroform (5 drops/5 ml) and sonicate for 15 min.
   3. Drop the final solution onto an ultrathin carbon film substrate with holey carbon support films on a 400 mesh copper Transmission Electron Microscopy (TEM) grid.
   4. Place the TEM grid in a glass vial and hold under vacuum overnight, to remove any residual solvent from the sample.
   5. Once the drying is completed, acquire TEM images using a 200 kV accelerating voltage, a spot size of 3 and an attached Energy Dispersive X-ray Spectroscopy (EDS) detector.
2. X-ray Diffraction 
   1. Dilute the isolated nanoparticles in chloroform (10 mg/ml).
   2. Clean molybdenum coated soda lime glass substrates (1 cm²) by sonicating in detergent, deionized water, acetone and isopropyl alcohol, each for 10 min. Finally, clean the substrates in an air plasma cleaner for 10 min prior to drop casting.
   3. Drop cast the solution from 4.2.1 onto the substrates from 4.2.2 in 7 µl increments.
   4. Once the films have dried, acquire X-ray Diffraction (XRD) data. Collect data using 7,000 data points at a scan rate of 1 data point per second with a Cu-Kα X-ray source and an incident wavelength of 1.54059 Å.
3. Solution Spectroscopy
   1. Disperse the isolated nanoparticles (0.1 mg/ml) in chloroform and sonicate for 30 min and place samples in a sealed quartz cuvette.
   2. Disperse the nanocomposite from section 2.6 and the sulfur copolymer from section 1.2.3 in formamide (1 mg/ml), stir at 700 rpm, and heat to 70 °C to facilitate suspension of the material.
   3. Acquire photoluminescence (PL) and absorbance spectra for all three samples. Conduct optical absorbance measurements using a spectrometer with a triple detector that extends across the ultraviolet, visible and near infrared ranges (UV-Vis-NIR). Conduct PL measurements using a fluorescence spectrophotometer with an excitation wavelength of 330 nm.
      NOTE: The specific protocol for characterizing nanoparticles using the techniques discussed in sections 4.1.5, 4.2.4, and 4.3.2 varies widely depending on the nature of the specific equipment used, so we present only general characterization parameters here. The interested reader is directed to several review papers for more information regarding using these analysis techniques for CdS nanoparticles.^17-19

Wyniki

The TEM image in Figure 3a shows small CdS nanoparticles (3-4 nm) that have nucleated within the sulfur copolymer before the sulfur copolymer has been completely removed. The image in Figure 3a was acquired by taking an aliquot of the nanoparticle solution immediately after the solution reached 200 °C. Figure 3b shows larger nanoparticles (7-10 nm) that have grown in solution for 30 min before the sulfur copolymer has been completely removed. Figure 3c

Dyskusje

We have developed a method to synthesize CdS nanoparticles within a sulfur copolymer matrix. This sulfur copolymer is composed of elemental sulfur and methylstyrene.⁵ An important feature of this method is that the copolymer can be used as both a high-temperature solvent and a sulfur source that reacts with a cadmium precursor to produce CdS nanoparticles in solution.⁵ The critical step in the procedure is the synthesis of the sulfur copolymer with a suitable ratio of methylstyrene and sulfur. The u...

Materiały

Name	Company	Catalog Number	Comments
Sulfur (S8), 99.5%	Sigma Aldrich	84683
α-methylstyrene, 99%	Sigma Aldrich	M80903
Cadmium acetylacetonate (Cd(acac)), 99.9%	Sigma Aldrich	517585	Highly Toxic
Chloroform (CHCl3), 99.5%	Sigma Aldrich	C2432
Hotplate / magnetic stirrer	IKA RCT	3810001
Temperature controller with probe and heating mantle	Oakton Temp 9000	WD-89800
Centrifuge	Beckman Coulter Allegra X-22	392186
Centrifuge Tubes	Thermo Scientific	3114	Teflon for resistance to chlorinated solvents
TEM with attached EDS detector	FEI Tecnai G2 F-20 with EDAX detector
TEM Sample Grid	Ted Pella	1824	Ultrathin carbon film substrate with holey carbon support films on a 400 mesh copper grid
XRD	Bruker F-8 Focus Diffractometer
Molybdenum coated soda lime glass substrates			750 nm thick sputtered molybdenum layer
Quartz Fluorescence Cuvettes	Sigma Aldrich	Z803073	10 mm by 10 mm, 4 polished sides with screw top
UV-Vis-NIR	Perkin Elmer Lambda 1050 Spectrometer		With 3D WB Detector Module
PL	Horiba FL3-21tau Fluorescence Spectrophotometer