Live Cell Imaging during Mechanical Stretch

Summary

A novel imaging protocol was developed using a custom motor-driven mechanical actuator to allow the measurement of real time responses to mechanical strain in live cells. Relevant to mechanobiology, the system can apply strains up to 20% while allowing near real-time imaging with confocal or atomic force microscopy.

Abstract

There is currently a significant interest in understanding how cells and tissues respond to mechanical stimuli, but current approaches are limited in their capability for measuring responses in real time in live cells or viable tissue. A protocol was developed with the use of a cell actuator to distend live cells grown on or tissues attached to an elastic substrate while imaging with confocal and atomic force microscopy (AFM). Preliminary studies show that tonic stretching of human bronchial epithelial cells caused a significant increase in the production of mitochondrial superoxide. Moreover, using this protocol, alveolar epithelial cells were stretched and imaged, which showed direct damage to the epithelial cells by overdistention simulating one form of lung injury in vitro. A protocol to conduct AFM nano-indentation on stretched cells is also provided.

Introduction

Cells are subjected to mechanical loads in many tissues, and this mechanical stimulation has been shown to promote changes in patterns of gene expression, release of growth factors, cytokines, or remodeling of the extracellular matrix and cytoskeleton^1-4. The intracellular signals transduced from such mechanical stimuli occur through the process of mechanotransduction^5-7. In the respiratory system, one outcome of mechanotransduction is the increase in reactive oxygen species (ROS)^8,9 and pro-inflammatory cytokines¹⁰ in pulmonary epithelial cells in the presence of cyclic tensile strain. Strong evidence also suggests that excessive tensile strain leads to direct injury to the alveolar epithelium, in addition to the biochemical responses of cells^11-14. Although the focus here is primarily on the response of lung cells to mechanical deformation, pathways induced by mechanotransduction play a key role in the basic function of many tissues in the human body, including the regulation of vascular tone¹⁵ and the development of the growth plate¹⁶.

The growing interest in mechanotransduction has resulted in the development of numerous devices for the application of physiologically relevant mechanical loads to cultured cells and tissue. In particular, devices applying a tensile strain, which is a common form of mechanical loading experienced by tissue, are popular ^11,17-19. However, many of the available devices are either designed as a bioreactor for tissue engineering applications or are not conducive to real time imaging with stretch. As such, there is a need to develop tools and methods that can visualize cells and tissues in tension to facilitate the investigation of pathways of mechanotransduction.

Herein, an in-plane mechanical stretching device was designed and protocols were developed to apply multiple forms of strain to tissues and cells while allowing imaging of the biochemical and mechanical responses in real time (Figure 1A-D). The device utilizes six evenly spaced clamps arranged circumferentially to grasp a flexible membrane and apply an in-plane, radial distention up to approximately 20% (Figure 1B). The actuating device can be placed in a cell culture incubator for an extended period of time, while the motor (Figure 1C) is positioned outside the incubator and controlled by proprietary software provided by the motor supplier. The motor is connected to a linear driver, which rotates an internal cam, driving the six stretcher clamps uniformly in tension and relaxation.

In addition to the mechanical device, customized flexible membranes were created from commercially available cell culture ready membranes to be used in the mechanical system. Then circular walls (with a diameter of approximately 28 mm) were made and attached on to the flexible membrane so that cells could be cultured only in this region of well-described strain profile. In order to determine whether the placement of these membranes within the actuating device would provide uniform and isotropic strain in the center of the flexible membrane, finite element analysis was conducted using commercially available software (Figure 1E-F). The flexible membrane was modeled with symmetric boundary conditions and utilizing all quadrilateral elements for the mesh. The concentric rings seen in the contour plot of maximum principal strain shown in Figure 1F indicate the isotropic distribution of the strain.

The strain experienced by the membrane was measured by recording images of markings through loading (Figure 2). Figure 2D shows that the average membrane strain measured in radial and axial directions was approximately linear with respect to the applied motor counts up to a maximum linear strain of 20%. There was no significant difference between the strain levels measured during distention compared with those measured during retraction back to the resting position. Next, the displacement of human bronchial epithelial cells (16HBE) and their nuclei cultured on the custom flexible membrane were measured. Fluorescently labeled (DAPI) nuclei of the 16HBE cells were imaged using a 20X objective under a confocal microscope, whereas whole cell displacement was measured with phase contrast images recorded with a digital microscope. As seen in Figure 3, the strain measured by displacement of nuclei was similar to that measured by displacement of markings on the membrane, up to ~20% linear strain. This confirms that the strain applied to the membranes was transmitted to the adherent cells. The protocols describing the use of the custom device on a traditional microscope and an atomic force microscope are provided in the following steps.

Protocol

1. Construction of Membrane with Well Walls for Retention of Cell Culture Media (see Figure 1D for the final product)

1. Using polydimethylsiloxane (PDMS) sheets coated with Collagen I, cut the outline of the flexible membrane with a scalpel or a die.
2. Place each membrane in a 60 mm Petri dish for storage.
3. Creation of walls:
   1. Mix PDMS at a 10:1 weight ratio of elastomer A to elastomer B (curing agent).
   2. Pour 5 ml of fully mixed PDMS into 50 ml tubes.
   3. Place 50 ml tubes with uncured PDMS horizontally in a hybridization oven.
   4. Use the rotor function to coat the inner walls of the tubes at 8 rpm during the curing time. At RT, the PDMS will be fully cured in 2 days.
   5. Remove the PDMS from the tube in a sterile cell culture hood.
   6. Using a new razor blade, partition the cylinder of PDMS into sections 4 mm in height.
   7. Place the sections, which will serve as the membrane walls, into a Petri dish container without allowing the walls to become creased.
4. Select and center one wall of PDMS on one membrane while maintaining the two in the Petri dish.
5. Gently place uncured PDMS (10:1 ratio) on the outside perimeter of the wall to be used as glue. Prevent formation of gaps between the wall and the membrane since it is there to retain liquid.
6. Place each Petri dish containing the completed membrane and covered in an oven at 70 °C for 24 hr to cure.

2. Correlation of Motor Rotations with Clamp Displacement or Radial Growth for Calibration (Figure 2)

1. Start the software controlling the motor.
2. Displace the clamps of the device using the manual setting in the motor software.
3. Measure the distance and record the motor count position between opposing clamps at both minimum and maximum displacement of the clamps.
4. Calculate the percent change in the distance between the clamps as a function of the motor count (~0-75k counts). This will indicate the maximum potential strain achieved on the membrane.

3. Application of Stretch on Mouse Lung Epithelial Cell Line (MLE12)

1. Seed MLE12 cells at 2.5 million cells on the flexible membrane (Step 1) per well to be confluent within two days. The seeding density may vary for different cell types.
2. Make sure the mechanical actuator is in a fully relaxed position.
   1. Remove cell culture media.
   2. Using 1.5 mm biopsy punches, punch two holes in each of the six clamp (see Figure 1D) tabs of the membrane. The radial placement of the holes determines the amount of pre-tension the membrane experiences initially. Punch the holes at a radius of 20.5 mm on the membrane tabs if no pre-tension is desired.
   3. Position the membrane on the stretcher with the punched holes lining up with the pins within the clamps. Place top clamps in place. Tighten the screws one at a time alternating sides.
   4. Add 1 ml cell culture media.
3. Place the device on the microscope stage centering the middle of the membrane with the light path.
4. Use tape or magnets (if possible) to fix the device to the stage. Once fixed, control the in-plane (parallel to the membrane) and vertical (z-direction) of the mechanical device with the stage controller of the microscope.
5. Apply stretch with the software provided by the manufacturer by manually controlling the position and speed of motor rotation²⁰.

4. Measurement of Mitochondrial Reactive Oxygen Species (ROS)

1. Once cells are confluent, add 1-2 ml of RT DMEM with mitochondrial superoxide indicator (5 µM final concentration) directly on the cells.
2. Incubate for 10 min at 37 °C.
3. Wash cells gently three times with buffer warmed in a water bath to 37 °C.
4. Immediately place the flexible membrane on the stretcher (Step 2.2) already in place under an upright confocal microscope.
5. Add 1 ml of DMEM with phenol-red free medium and 25 mM of HEPES.
6. Set excitation/emission filters to 510/580 nm.
7. Image multiple fields every 15 min to create the desired time course of mitochondrial superoxide production.
8. From captured images, record fluorescence intensity histograms at each time interval using software capable of quantifying fluorescence intensity.

5. Application of Stretch and Atomic Force Microscopy (AFM)

NOTE: These steps are provided for a specific AFM and optical microscope combination (Figure 4 and Materials List).

1. Prepare the AFM for the experiment.
   1. Increase the height of the AFM head to its maximum position in the z-direction.
   2. Put extenders on the legs of the AFM to lift the plane at which AFM cantilever contacts the sample. The specimen and the AFM head needs to be lifted to accommodate the height of the mechanical device.
2. Prepare the optical microscope (if available).
   1. Remove the AFM scanner plate. Remove the desired objective.
   2. Add a spacer to the objective. The height of the spacer would depend on the objective and the specific AFM set-up, but it is necessary if optical imaging is desired since observation plane will be shift in the z-direction by an amount equal to the stretcher and adapter height (Figure 5A). Note that the AFM usually provides low magnification imaging from an optical path above the device.
   3. Mount the desired objective back in its location. Place the scanner back on to the AFM.
   4. Start the AFM software. Start all necessary light sources including the light source for fluorescence measurements.
   5. Mount a chip with a cantilever beam that is appropriate for the desired measurements. 200 pN/nm or less stiffness is preferred when measuring the elastic modulus of live cells.
   6. Align the laser and calibrate the cantilever stiffness according to manufacturer’s suggestions on a glass coverslip mounted on the device.
3. Prepare a membrane as in Step 1, but with the following modifications.
   1. Immediately before mounting the membrane on to the stretching device, cut the walls to about 1 mm in height. This prevents the interference experienced between the membrane walls and the load cell.
   2. Mount the membrane on the mechanical device as described 3.2.1-3.2.3.
   3. Remove cell culture media to prevent damage to the AFM scanner in case of a spill.
   4. Couple the device with an adapter (Figure 5A). Place the mechanical device with the adapter on the scanner.
   5. Stretch the membrane to the desired tensile strain level.
4. Nano-indentation of stretched cells.
   1. Add a limited (<0.5 ml) volume of media on the cells to avoid AFM scanner or microscope damage due to a spill.
   2. Engage the cantilever beam with the membrane.
   3. Follow the protocol of the particular AFM device to scan areas of interest. 

Results

Reactive Oxygen Species and Deformation

Previous studies have shown increases in reactive oxygen species (ROS) in airway and alveolar epithelial cells in response to cyclic stretch²¹. Reactive oxygen species include molecules and free radicals derived from molecular oxygen with high reactivity to lipids, proteins, polysaccharides, and nucleic acids^22-24. ROS serve as a common intracellular signal to regulate ion channel function, protein kinase/phosphatase activa...

Discussion

A unique device for live cell imaging during mechanical stretch was developed; and this device was used in a protocol to study lung epithelial cell mechanobiology. In preliminary studies, it was found that a single held stretch stimulated the production of mitochondrial superoxide in bronchial epithelial cells. In addition, it was demonstrated that increased levels of mechanical strain caused direct damage to the integrity of a monolayer of alveolar epithelial cells.

To conduct these prelimina...

Materials

Name	Company	Catalog Number	Comments
SmartMotor NEMA 34: 3400 Series	MOOG Animatics	SM3416D	Integrated motor, controller, amplifier, encoder and communications bus
Flexcell Membrane (Collagen I coated)	Flexcell International Corp	SM2-1010C	3.5" x 5.25" x 0.020"
Sylgard 184	Dow Corning Corporation		10:1
Hoechst 33342	Sigma-Aldrich	H1399	DAPI stain
MitoSOX	Sigma-Aldrich	M36008
Tiron	Sigma-Aldrich	D7389	mitochondrial superoxide label
DMEM			superoxide inhibitor
FBS
HEPES
50 ml tubes	Fisher Scientific	06-443-19	Any centriguge tube can be used to create an area for imaging.
Hybridization oven	Bellco Glass
MLE12 Cells	ATCC	CRL-2110	Mouse Lung Epithelial Cells
16HBE cells	ATCC	CRL-2741	Human Bronchial Epithelial Cells
AFM Indentation Experiments
Cantilever Beams for Nano-indentation	Budget Sensors	Si-Ni30
AFM	Asylum Research	MFP3D
Olympus microscope	Olympus	IX-71	Inverted microscope with 20X and 40X objectives.
AFM Leg Extenders	Asylum Research	Not available	AFM microscope
Finite Element Analyses
ABAQUS	Simulia	6.12
Software
ImageJ	NIH
Microscopes
Digital microscope	Life Technologies	EVOS XL Core	Initially a self standing company, now owned by Life Technologies.
Confocal microscope	Zeiss	LSM 710	2-photon upright microscope