9.4K Views
•
08:51 min
•
October 24th, 2017
DOI :
October 24th, 2017
•0:05
Title
0:45
Synthesis of 2,8-Bis(3,6-di-tert-butyl-9H-carbazol-9-yl)dibenzothiophene-S,S-dioxide (Compound 4)
4:39
Synthesis of 2,8-Bis(10H-phenothiazin-10-yl)dibenzothiophene-S,S-dioxide (Compound 5)
6:44
Results: Characterization of Thermally Activated Delayed Fluorescence (TADF) Emitters
7:38
Conclusion
필기록
The overall goal of this procedure is the chemical synthesis of highly efficient organic materials for organic light emitting diode applications, from commercially available starting materials. This method can help answer key questions in organic electronics, but use of family activited delayed florescence, and lighting applications. And an advantage of this technique is that it uses regularly available materials and is accessible to researchers with little experience in synthetic organic chemistry.
Demonstrating the procedure will be Oleh Vybornyi, a PhD student from the Schibello Research Group and a member of the excellent project. To begin the synthesis of Compound 4 in a three neck round bottom flask, dissolve 0.80 grams of Compound 1 and 0.45 grams of Compound 3 in 250 milliliters of Anhydrous Tellurite. Open a Nitrogen source and connect to the reaction flask.
Then, open up Nitrogen valve and place a needle into the solution. Degas the mixture by bubbling nitrogen gas through the mixture for 15 minutes while stirring vigorously. Add 0.025 grams of Palladium DBA and 0.06 grams of Xfos.
And degas the mixture for another 15 minutes, while stirring. It was cut and go stuff with the procedure as the addition of the Palladium catalyst and the Xfos followed by degassing for 15 minutes. This must be done quickly, to avoid degradation of the chemicals and the arc bio station.
Next, add 0.32 grams of Sodium Turputoxide and six milliliters of tert-Butanol and degas the mixture for 15 minutes. Then, put the mixture under a nitrogen atmosphere. Stir the degassed reaction mixture for 18 hours at 110 degrees Celsius.
Check the completion of the reaction by looking at the solution with a UV lamp. When complete, the solution should glow with a blue light. Then, allow the mixture to cool to room temperature.
Dilute the mixture with 150 milliliters of water and extract the product into 250 milliliters of DCM. Check the separation of the organic and aqueous layers by looking with a UV lamp. The organic layer should glow with a green light.
Wash the organic layer with 150 milliliters of water, twice. Dry the organic layer over 15 grams of Magnesium Sulfate. Filter the product mixture and remove the solvent under vacuum.
Dissolve the residue in a one to one mixture by volume of DCM and Petroleum Ether. Purify the crude product by Column Chromatography. For easier purification, use a UV lamp.
The solution of the compound should glow with a bright green light. Remove volatiles under vacuum to obtain Compound 4 as a white solid. The resulting compound must glow with a blue light, under the UV a radiation.
To begin synthesizing Compound 5 in a 250 milliliter three neck round bottom flask, dissolve 0.67 grams of Compound 3 and 0.75 grams of Phenothiazine in 60 milliliter of Anhydrous Toluene. Degas the mixture, by bubbling Nitrogen gas for 15 minutes while stirring vigorously. Then, add 0.11 grams of Palladium DBA and 0.12 grams of Xfos.
And degas the mixture for 15 minutes. Add 0.38 grams of Sodium tert butoxide and degas the mixture for another 15 minutes. Then, under a nitrogen atmosphere, stir the reaction mixture for 18 hours at 110 degrees Celsius.
Allow the mixture to cool to room temperature. Dilute the mixture with 150 milliliter of water. Extract the product into 250 milliliter of DCM and wash with two 150 milliliter portions of water.
Dry the organic layer over 15 grams of Magnesium Sulfate. And filter the mixture. Remove the solvent under vacuum.
And dissolve the crude product in a two to one mixture by volume of DCM and Hexanes. Purify the compound with Column Chromatography and remove volatiles to obtain Compound 5 as a white solid, which glows with a green light under the UV a radiation. Toluene solution has an orange luminescence, due to the solvatochromism.
Two TADF emitters were prepared by a palladium catalyzed amination cross coupling reaction. Compound 4 was obtained in 63%yield and Compound 5 was obtained in 55%yield. Increasing the amounts of starting materials did not negatively impact the yields, suggesting that the reactions can be carried out on an even larger scale.
The difference in photo physical properties between compounds is attributed to the different properties of the electron donating groups. Alko groups are introduced in the carbazole units used in Compound 4 to improve the compound solubility in organic solvents. The synthesis of Compound 5 uses commercially available Phenothiazine without modifications.
After its development this technique paved the way for non chemistry sectors in optoelectronics to become familiar with the preparation of these TADF emitters. Which could help them investigate the potential lighting applications for these compounds. Once mustered, the reaction can be set up in one hour if it's performed properly.
The isolation of the product should take three hours. Following this procedure, other palladium catalyzed cross coupling reactions can be performed to answer additional questions about the sensors of TADF emitters. After watching this video, you should have a good idea of how to obtain and purify TADF emitters for further study.
While attempting this procedure, remember to carefully weigh the starting materials and degas the reaction mixture properly. Don't forget, that working with chemicals can be extremely hazardous. Please remember to follow all appropriate safety rules.
Including the use of a fume head and personal protective equipment while performing this procedure.
Scale-up synthesis of highly efficient thermally activated delayed fluorescence emitters is described in the presented article.
JoVE 소개
Copyright © 2024 MyJoVE Corporation. 판권 소유