RNA-Seq Analysis of Differential Gene Expression in Electroporated Chick Embryonic Spinal Cord

Summary

This video shows the basic steps for performing whole transcriptome analysis on dissected chick embryonic spinal cord samples after transfection with in ovo electroporation.

Abstract

In ovo electroporation of the chick neural tube is a fast and inexpensive method for identification of gene function during neural development. Genome wide analysis of differentially expressed transcripts after such an experimental manipulation has the potential to uncover an almost complete picture of the downstream effects caused by the transfected construct. This work describes a simple method for comparing transcriptomes from samples of transfected embryonic spinal cords comprising all steps between electroporation and identification of differentially expressed transcripts. The first stage consists of guidelines for electroporation and instructions for dissection of transfected spinal cord halves from HH23 embryos in ribonuclease-free environment and extraction of high-quality RNA samples suitable for transcriptome sequencing. The next stage is that of bioinformatic analysis with general guidelines for filtering and comparison of RNA-Seq datasets in the Galaxy public server, which eliminates the need of a local computational structure for small to medium scale experiments. The representative results show that the dissection methods generate high quality RNA samples and that the transcriptomes obtained from two control samples are essentially the same, an important requirement for detection of differential expression genes in experimental samples. Furthermore, one example is provided where experimental overexpression of a DNA construct can be visually verified after comparison with control samples. The application of this method may be a powerful tool to facilitate new discoveries on the function of neural factors involved in spinal cord early development.

Introduction

Genetic studies on live organisms frequently use the chicken embryo as a model because in ovo electroporation represents a fast and inexpensive way to partially transfect embryonic structures in vivo with DNA constructs^1-5. Bicistronic expression vectors that encode one transcript containing a fluorescent reporter together with the gene of interest, such as pCIG⁶ or pMES⁷, allow quick verification of transfection quality in the desired region under a stereomicroscope before processing embryos for downstream analysis.

With recent advances in DNA sequencing, it is now possible to obtain digital whole transcriptome expression profiles from RNA samples using RNA-Seq^8,9. Therefore, instead of time-consuming methods that enable analysis of only a few gene products in parallel, such as in situ hybridization, immunohistochemistry and qPCR, preparation of cDNA libraries for high-throughput sequencing can provide information of the whole transcriptome. Observation of the experimental effects on the expression levels of every single gene may in turn provide powerful insights on the pathways altered by the construct used. This is particularly easy if a genomic assembly for the organism used is available, thus the chick embryo again is a suitable model.

If the user has access to a reliable genome sequencing center, the main issue is obtaining high quality RNA samples. This work demonstrates a method for obtaining RNA samples from transfected neural tubes suitable for RNA-Seq, as well as the downstream steps for in silico analysis of the resulting datasets. After electroporation at HH12-13 followed by 48 hr incubation, transfected trunk spinal cord halves were dissected in ribonuclease-free conditions, immediately lysed and further protected from degradation by ultra-low freezing until RNA purification and library preparation.

The Galaxy public server¹⁰ provides access to free resources for analyzing high-throughput sequencing data. The amount of space offered for registered users is enough for small experiments, thus eliminating the need for local computational infrastructure. RNA-Seq data analysis includes filtering, alignment and quantitation/comparison of gene expression. Although there are general guidelines for RNA-Seq data analysis, filtering parameters will largely depend on the quality of sequencing and should be determined after quality control analysis of the raw data.

This protocol describes the steps to obtain and compare RNA-Seq profiles from chicken embryonic spinal cords transfected in vivo. As a representative result, comparison of datasets obtained from two independent control samples transfected with an empty vector showed that the method is reproducible and should allow identification of differentially expressed transcripts in experimental samples. Therefore, application of this method has the potential to greatly increase the number of discoveries after one single experiment and thus provide a large set of data for subsequent investigation.

Protocol

1. Electroporate the Construct of Interest in the Neural Tubes of HH12-13 Chicken Embryos In ovo

Use a fluorescent reporter, preferably in a bicistronic transcript or fused to the protein of interest with an intercalating viral 2a peptide¹¹, to enable quick identification of individuals with satisfactory levels of transfection. NOTE: Typical incubation time for this stage is around 48 hr at 37.8 °C.

1. Open a small window in the eggs after removing 3 ml of albumin with a syringe coupled to a 18 G x 1 1/2 needle. To enhance embryo visualization, inject a small amount of Indian ink diluted 1:50 in sterile Ringer’s solution underneath the embryo^1-4.
2. After covering the embryo with sterile Ringer’s solution, inject a 10 mM Tris-HCl, pH 8.2 and 0.1% Food Dye (F, D & C) solution containing 2.5 µg/µl DNA through the posterior end of the neural tube until it fills up to the hindbrain region. To electroporate, position platinum electrodes (0.5 mm in diameter) separated by 4 mm¹ along the flank region and deliver 5 pulses of 50 msec and 20 V with an interval of 100 msec between them⁴.
3. After electroporation, incubate manipulated embryos for 48 hr more until they reach stage HH23 and identify individuals presenting high level of transfection at the flank region under a fluorescent stereomicroscope.
   NOTE: The duration of incubation after electroporation depends on the aim of the experiment. The electroporated plasmids can generate significant expression levels after 2 hr². Thus, if the interest lies in early onset genes the post-electroporation incubation period can be reduced.

2. Harvest Successfully Transfected Embryos and Dissect the Electroporated Spinal Cord Halves

NOTE: This procedure lasts from 2-3 hr for each 10 embryos and yields 1-2 µg total RNA per embryo. The dissection of neural tubes requires fine movements and some practice sessions may be necessary before applying it to experimental samples.

1. Decontaminate metallic dissection tools with RNase decontamination solution or by baking at 150 °C for 4 hr¹² and prepare DEPC-treated PBS. Use only new certified RNase-free plasticware.
   NOTE: After harvesting, it is important to follow standard care to prevent RNase contamination during dissection.
2. Harvest the embryos using a pair of fine dissecting scissors and a sieved collection spoon. Keep the embryos in cold DEPC-treated PBS in a 100 mm Petri dish.
3. With a pair of fine tweezers, cut out the whole flank region (between the posterior limit of the anterior limb bud and the anterior limit of the posterior limb bud) and transfer this section to a new dish containing cold DEPC-treated PBS.
4. Use two fine glass needles to perforate at three different points on each dorsolateral side of the embryo between the neural tube and the paraxial mesoderm.
5. Introduce the two glass needles in the central perforation and slowly move one of them away along the neural tube anterior-posterior axis. Repeat this for the perforations that were not reached by the first movements. Remove the detached paraxial mesoderm with a pair of fine tweezers.
6. Turn the embryo sideways, insert the tips of the tweezers between the neural tube and the notochord and slide them in opposite directions along the anterior-posterior axis to separate the two structures.
   NOTE: This should also remove most of the mesoderm still attached to the neural tube.
7. If necessary, remove any larger pieces of mesodermic tissue that remain attached by pulling with a pair of tweezers while lightly holding the neural tube with another pair of tweezers. When finished, gently transfer the neural tube to another dish containing cold DEPC-treated PBS using a RNase-free glass Pasteur pipette coupled to a manual pipette pump and keep on ice until all the tubes are dissected.
8. Divide the neural tubes into two halves. For this, insert the sharp tip of a closed pair of tweezers in the lumen and open the roof plate by moving the tweezers out through it. After this, separate the halves by cutting the floor plate with the tweezers tips.
9. Sort electroporated from non-electroporated halves under a fluorescent dissecting scope and transfer to a 1.5 ml tube filled with ice-cold DEPC-treated PBS. If necessary, flick the microtubes gently to release any tissue attached to the plastic walls and to promote sedimentation of the tubes.
10. Spin at 100 x g for 3 sec and remove very slowly as much PBS as possible with a 1 ml micropipette. Do this while looking at a light source that shines through the microtube to monitor if any embryonic material is sucked to the pipette tip; if this happens, slowly discharge and repeat the centrifugation.
11. Add 70 µl of lysis solution for RNA extraction per neural tube half and flick the tube to mix contents. Incubate at room temperature for 5 min and vortex vigorously. Repeat the 5 min incubation and vortexing two more times. Store at -80 °C.
12. Collect at least eight neural tube halves per sample to ensure an adequate yield for the next step. Pool smaller samples if several electroporation/dissection sessions are required to amass sufficient number of neural tubes. Store sufficient samples for duplicates or triplicates for each condition.

3. Purify RNA and Prepare Libraries for Illumina Sequencing

1. Remove samples from -80 °C storage and place on ice for 15-30 min. Resume thawing at room temperature until complete.
2. Vortex well and leave at room temperature for 5 min. Vortex again and centrifuge at 15,000 x g for 1 min to pellet insoluble material.
3. Transfer the supernatant to a new tube and proceed to RNA extraction according to the total RNA isolation kit manual instructions. Elute in the minimum recommended volume to increase concentration.
   NOTE: DNase treatment after clean-up is recommended in order to avoid potential contamination of genomic DNA sequences in RNA-Seq datasets.
4. Flick the tube to mix contents and remove 5 µl for quality control analysis. Store the remaining sample at -80 °C until library preparation; these samples should be thawed only once to avoid RNA degradation.
5. Run purified RNA in a Bioanalyzer instrument using the RNA 6000 Nano kit; RIN value must be at least above 7 to proceed.
6. Generate libraries using an Illumina compatible RNA-Seq library preparation kit and multiplex up to 4 libraries in one lane of a HiSeq instrument set to generate 100 bp single reads. If possible, include all samples in the same run to minimize potential technical artifacts.
   NOTE: This should yield up to 50 million reads per sample, which is more than enough to obtain coverage for most genes¹³.

4. Compare RNA-Seq Datasets in the Galaxy Public Server¹⁰.

NOTE: Server storage space is limited and experiments comparing many samples may require deletion of intermediate files generated in the filtering steps.

1. Create a user account in the Galaxy public server (https://usegalaxy.org) and FTP upload the Illumina datasets in fastq format.
2. Prepare uploaded files with the FastqGroomer¹⁴ tool under the NGS:QC and manipulation menu; if the quality scores are already encoded in Phred+33 (Sanger), skip this step by simply changing the file type to fastqsanger under the Attributes for each dataset.
3. Analyze the general quality of each dataset using the FastQC tool under the NGS:QC and manipulation menu.
   NOTE: Special attention should be given to the resulting graphics for per base sequence quality and per base sequence content, as these will provide estimates for the parameters used for trimming the ends of the reads.
4. Trim reads to discard 3’ ends with low quality data using the tool FASTQ Quality Trimmer¹⁴ under the NGS:QC and manipulation menu. Set the tool to process only 3’ ends for quality score below 20.
5. Remove adapter sequences from reads using the Clip tool (http://hannonlab.cshl.edu/fastx_toolkit/) under the NGS:QC and manipulation menu. Set the tool to discard reads with less than 45 bp left, input the sequence of the adapter used and choose the output to include both clipped and non-clipped sequences. Additionally, opt not to discard sequences with unknown bases since most low quality bases were already removed in the last step.
6. Using the tool Trim sequences (http://hannonlab.cshl.edu/fastx_toolkit/) under the NGS:QC and manipulation menu, trim the first bases of the reads to remove 5’ sequence bias detected by FastQC (typically 10).
   NOTE: At this point, it is a good idea to run FastQC again and compare with the previous analysis to determine if the dataset quality was improved.
7. Download and unpack the latest chicken genome assembly for the UCSC genome browser from Illumina iGenomes (http://support.illumina.com/sequencing/sequencing_software/igenome.ilmn) and upload the whole genome fasta format file and the genes annotation gtf format file to the Galaxy history using the tool Upload File under the Get Data menu.
8. Map reads for each sample to the chicken genome using the aligner TopHat2¹⁵ under the NGS: RNA Analysis menu. Choose to use a genome from History (select the fasta file uploaded in step 4.7).
9. Build a predicted transcriptome for each sample using Cufflinks¹⁶ under the NGS: RNA Analysis menu. Choose to use reference annotation as a guide (select the gtf file uploaded in step 4.7) and turn on the options Perform Bias Correction (from History, fasta file from step 4.7) and Use multi-read correct.
10. Merge predicted transcriptomes for all samples using Cuffmerge¹⁶ under the NGS: RNA Analysis menu. Choose to use reference annotation (gtf file from step 4.7) and sequence data (from History, fasta file from step 4.7).
11. Compare BAM files generated by TopHat2 for each sample using Cuffdiff¹⁶ under the NGS: RNA Analysis menu. In the field Transcripts select the merged transcriptome generated by Cuffmerge and turn on the options Perform Bias Correction (from History, fasta file from step 4.7) and Use multi-read correct.
12. Sort differential expression testing tables numerically ascending in column 13 (q value) using the tool Sort under the Filter and Sort menu.
    NOTE: Genes/transcripts showing significant differential expression between experimental conditions will present the lowest q values.
13. To check results visually with coverage graphs, first convert BAM files to bedGraph format using the tool Create a BedGraph of genome coverage¹⁷ under the BEDTools menu. Disable reporting of regions without coverage, choose to treat spliced entries as distinct intervals and scale the coverage by a factor that normalizes sequencing depth for all the datasets being compared.
14. Convert the resulting bedGraph file to bigWig format using the tool Wig/BedGraph-to-bigWig (http://www.genome.ucsc.edu/) under the Convert Formats menu. Upload the bigwig files as custom tracks in the UCSC genome browser (http://www.genome.ucsc.edu/) for the galGal4 assembly and search a gene of interest to visualize the coverage in the datasets.

Results

To validate the method described, two control samples were generated from embryos electroporated with the empty vector pMES⁷ and one sample from embryos transfected with the same vector containing the insert construct SCRT2-ZNF, which encodes the zinc-finger domains of chicken SCRT2¹⁸. Samples yielding 11-22 µg total RNA each were obtained from pools of 8 to 12 embryos. All three samples scored an optimal RIN value of 10 in a quality check performed with the Bioanalyzer instrument (Figu...

Discussion

Here we provide guidelines for analyzing effects after electroporation of the chicken spinal cord. Although electroporation of DNA vectors is more frequently used to overexpress a gene of interest, one can also use constructs encoding dominant negatives, quimeric proteins or precursors for siRNAs to generate gene function knock-down conditions^19-21. In fact, comparison of transcriptome profiles resulting from both gain- and loss-of-function analysis may point out genes differentially expressed in opposite ways...

Materials

Name	Company	Catalog Number	Comments
Indian ink	Any supplier
18G x 1 1/2 needle	BD	305196
3 ml syringe	BD	309657
Tris	MP Biomedicals	819620
F D & C Blue 1	Spectra Colors Corporation	5.FC.0010P0	Food Dye used to visualize DNA injection
Ringer's solution (1 L)
- 7.2 g NaCl	Sigma-Aldrich	S-9888
- 0.37 g KCl	Sigma-Aldrich	P-4504
- 0.225 g CaCl2•2H2O	Fisher Scientific	10043-52-4
- 0.217 g Na2HPO4.7H2O	Sigma-Aldrich	S-9390
- 0.02 g KH2PO4	Sigma-Aldrich	P-5379
- ddH2O to 800 ml and adjust pH to 7.4
- ddH2O to 1 L
- Filter and autoclave
PBS (Phosphate Buffered Solution) (1 L)
- 8 g NaCl	Sigma-Aldrich	S-9888
- 0.2 g KCl	Sigma-Aldrich	P-4504
- 1.15 g Na2HPO4•7H2O	Sigma-Aldrich	S-9390
- 0.2 g KH2PO4	Sigma-Aldrich	P-5379
- ddH2O to 800 ml and adjust pH to 7.2
- ddH2O to 1 L and filter
- 1 ml DEPC (Diethylpyrocarbonate)	Sigma-Aldrich	D-5758
- Shake vigorously and let stand overnight at room temperature
- Autoclave
Sieved spoon	Any supplier
Sterile 60 x 15 mm polystirene Petri dishes	Corning Life Sciences	351007
RNaseZap RNase decontamination solution	Life Technologies	AM9780
Fine point surgical scissors	Any supplier
Straight fine point tweezers	Any supplier
Pulled glass needle made from 1.1 x 75 mm glass capillary tubes	Kimble Chase	40A502
9'' glass Pasteur pipette	Any supplier
Manual pipette pump	Any supplier
Clear 1.5 ml microcentrifuge polypropilene tubes	Corning Life Sciences	MCT-150-C
Microcentrifuge	Any supplier
RNAlater solution for RNA stabilization	Life Technologies	AM7020
RNAqueous total RNA isolation kit	Life Technologies	AM1912
Molecular Biology Grade Ethanol	Any supplier
RNA 6000 Nano Kit	Agilent Technologies	5067-1511
2100 Electrophoresis Bioanalyzer Instrument	Agilent Technologies	G2939AA
Truseq RNA Sample Preparation Kit v2	Illumina	RS-122-2001/RS-122-2002